Results 1 to 10 of 10

Thread: 1990 chevy 2500 computer issues

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Carb and Points!
    Join Date
    Apr 2014
    Age
    50
    Posts
    5

    1990 chevy 2500 computer issues

    I purchased a non running 1990. Rebuilt the motor and cant get it to run right. I've found evidence that the computer has been changed or tampered with. It's a 1228747. I've been reading that this model doesn't support knock sensor and ESC. Both of which I have on this motor. I need help figuring out what computer was original to this truck.

    I've replaced the distributor, map, TPS, knock, TBI, plus/wires, O2(twice). It seems to run Ok with spout disconnected while cold. When it warms up it Idles high then low then high. With spout connected it misses on idle runs ok at high rpms. seems like when the computer takes over, it craps out!
    Last edited by tbitrouble; 04-26-2014 at 08:01 PM. Reason: more info

  2. #2
    Fuel Injected! jim_in_dorris's Avatar
    Join Date
    Dec 2011
    Posts
    803
    1228747 is original to truck, what BCC is it running. What the ??? is a spout? Hunting idle is usually (but not always) a vacuum leak.
    Square body stepsides forever!!!

  3. #3
    Carb and Points!
    Join Date
    Apr 2014
    Age
    50
    Posts
    5
    It's the single wire timing connector. Sorry, I've heard it refered to as a spout. I don't know what BCC is. So does the 1228747 support knock and ESC? Dealer also lists this as stock to the VIN.

    Also, I've just found carbon crammed in my EGR not sure where it came from. (Crossing fingers, hope this is it.)

  4. #4
    RIP EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    64
    Posts
    10,477
    Spout is usually a Ford term... yes that truck cam with a 122778747 ECM in 3/4 ton models with TH400!

    The BCC is Broad Cast Code and GM name for the four letter chip code that came on your chip. WHen you buy a replacement ECM it does not come with a Chip. You use your old one. It would be good at this point to open your ECM and read the BCC from top of chip to see what this thing really is and make sure the BCC matches 1228747 and not 1227747 ECM.

    Carbon filled passages on EGR is common and needs to be cleaned and blown out. Can cause your vacuum leak if EGR is not closing properly.

    When ECM takes over it is usually going Closed Loop, before that Open Loop. Only real change is fueling correction.

    Watch your CEL when Key on? Should come on, blink and stay on till engine starts then goes off!

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  5. #5
    Carb and Points!
    Join Date
    Apr 2014
    Age
    50
    Posts
    5
    Mine has the sm465. BCC is AKWH

  6. #6
    Carb and Points!
    Join Date
    Apr 2014
    Age
    50
    Posts
    5
    So I cleared the EGR valve and still have issues. I've searched long and hard for a vacuum leak and have not found one. How common is it for the intake to leak or crack on the underside?

Similar Threads

  1. LS computer ('0411) running a Small Block Chevy
    By dave w in forum GM EFI Systems
    Replies: 39
    Last Post: 10-19-2016, 11:06 PM
  2. L29 1996–1999 Chevrolet Suburban 2500 crank trigger
    By delcowizzid in forum GM EFI Systems
    Replies: 3
    Last Post: 07-11-2014, 10:09 AM
  3. GM MEFI Computer / Crate 502 Engine Computer
    By dave w in forum OBDII Tuning
    Replies: 29
    Last Post: 04-29-2014, 11:53 PM
  4. Replies: 58
    Last Post: 08-07-2013, 09:20 PM
  5. 1994 chevy 2500 5.7cid erratic timing
    By TRBBenicia in forum GM EFI Systems
    Replies: 3
    Last Post: 06-06-2013, 08:00 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •