Results 1 to 9 of 9

Thread: Make your own carb to TBI adapter

  1. #1
    Carb and Points!
    Join Date
    Jun 2015
    Age
    75
    Posts
    4

    Make your own carb to TBI adapter

    Make your own carb to tbi adapter for an inline 6. Use your gaskets as the templates. The upper and lower plates are 3/8" thick. The side pieces are 1/8" thick. cut a 1 3/4" pipe at 172 degrees, 1 7/8" long and then split the pipe and flip one side and you have the 2 sides, cut the triangle pieces to fill in the voids. It ends up at 2 1/4" tall. Thread the upper plate for the tbi unit. I used my drill press to keep my tap square to the plate. I used a regular 1 3/4" hole saw at slow speed with plenty of cutting fluid to cut the holes. Hope this helps.
    Attached Images Attached Images

  2. #2
    Fuel Injected!
    Join Date
    Sep 2012
    Location
    washington indiana
    Age
    69
    Posts
    884
    them are handy, if eagle mark was here he would say commiting adultry

  3. #3
    Carb and Points!
    Join Date
    Jun 2015
    Age
    75
    Posts
    4
    Label me confused. I don't have the slightest clue of what your reply means

  4. #4
    Fuel Injected!
    Join Date
    Sep 2012
    Location
    washington indiana
    Age
    69
    Posts
    884
    eaglemark was a narriator in 2012,showed a lot of gearheads help for shore

  5. #5
    Super Moderator Six_Shooter's Avatar
    Join Date
    Feb 2011
    Posts
    2,968
    Quote Originally Posted by ony View Post
    eaglemark was a narriator in 2012,showed a lot of gearheads help for shore
    He actually started this site. He's greatly missed.
    The man who says something is impossible, is usually interrupted by the man doing it.

  6. #6
    Electronic Ignition!
    Join Date
    Dec 2022
    Age
    59
    Posts
    11
    Nice Work.

  7. #7
    Carb and Points!
    Join Date
    Jun 2015
    Age
    75
    Posts
    4

    Thank you

    el Jefe;96833]Nice Work.

    Thank you, It's running great. I used the pcm, harness and hardware from an S10 4.3 engine

  8. #8
    Fuel Injected!
    Join Date
    May 2014
    Age
    41
    Posts
    149
    nice work, but if you know how to weld why not open up that intake manifold to breath more air ?

  9. #9
    Fuel Injected!
    Join Date
    Mar 2023
    Posts
    64
    Which inline is this for? Looks like it would fit my 59 235 intake. How much to make another? lol

Similar Threads

  1. How to make an XDF file
    By custodian in forum OBDII Tuning
    Replies: 3
    Last Post: 02-21-2022, 05:37 AM
  2. How to make XDF file
    By exceedbeyond in forum OBDII Tuning
    Replies: 11
    Last Post: 08-29-2020, 01:46 AM
  3. How do I make dis work from dizzy?
    By f85gtron in forum GM EFI Systems
    Replies: 5
    Last Post: 06-30-2016, 11:17 PM
  4. Can't seem to make a signature
    By troutdog311 in forum GearHead EFI Forum Support
    Replies: 1
    Last Post: 10-09-2015, 12:22 AM
  5. Can you make TBI squirt fuel like carb
    By joegreen in forum GM EFI Systems
    Replies: 12
    Last Post: 07-15-2014, 07:29 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •