The newer LS style engines have a longer, larger diameter input shaft and the V8 converters are much larger in diameter. My old 2.8 had like a 9.5" converter and my 350 was atleast 12". The newer stuff is atleast 11". If the colorado and trailblazer share converters it likely will not even fit in the 2.2 bellhousing.
93-94 were non-pwm TCC apply whereas the 95 and up are all pwm. I usually eliminate the pwm function and revert back to a simple on-off TCC. The pwm TCC was instituted for a few reasons such as converter lock-up feel especially with different tcc clutch lining materials used for different vehicles with different holding capacity. Depending on the application you can eliminate the pwm function without worry of anything more than a firmer tcc lockup.
If it don't fit force it, if it don't force fit f&%@ it!
If it don't fit force it, if it don't force fit f&%@ it!
Ya, I'm still working on the controller. Need to line out a few more items before its ready for the road and time is not my friend at the moment. Still waiting on Steveo to send me the updated code for review. Anywho, here's the thread on my controller project if you're interested or just curious.
http://www.gearhead-efi.com/Fuel-Inj...ion-controller
Buddrow
If it don't fit force it, if it don't force fit f&%@ it!
Yes the 60* v6 input shaft and converter, is all its own, similar to the 2.2L 4 cyl stuff.
As for the 60E stuff into your pcm, its doubful it will be easy to accomplish. As mentioned earlier, I am working on a controller for the 60E as well as the 80E. It is in development currently with no determined time to market. May be 2 weeks, may be 2 months. If you can stand the wait, hang out and follow my thread and we will get you going with the 60E. Bear in mind that the 60E is marginal as an off-road trans without some internal upgrades.
if you are in a hurry you might check out the Megashift controller from the guys at Megasquirt.
Buddrow
If it don't fit force it, if it don't force fit f&%@ it!
You might also be able to find an ECM that will controll the 60E and the engine and swap that in place of your current ECM.
The man who says something is impossible, is usually interrupted by the man doing it.
awesome, I can wait a couple months, I know the 60e isnt the best option but the 30s worse lol the 60 atleast has the aftermarket support. Looks like ill be looking into making the colo 60 into 60° bell housing a little further. Ill prob be getting a 2.2 trans not just housing so may just swap the input shaft over, not simple but very doable
Last edited by Rodeo; 04-10-2014 at 01:59 AM.
If you get the 2.2L trans you shouldn't have to swap input shafts. The I6/L5 trailblazer/colorado bellhousings and converters are specific to those engines so I would look for either the 2.2 or V6 bell/converter setup. The trans is going to have to be gone through to change the output shaft for a 4wd unless you find a 2.2L 4wd S-10 trans. And you will have to procure the t-case adapter from the colorado trans if you're wanting to use the isuzu tcase. You might also look at Isuzu Hombre trucks for trans. may have just the setup you're looking for.
Buddrow
If it don't fit force it, if it don't force fit f&%@ it!
The hombre is the sameas a s10, just diffrent grill. I want to use the colorado trans because it has a diffrent valve body and pan that create clearance for the front drive shaft, if I swap tail shafts and use the s10 trans the front shaft will hit the pan. I esentially need to use the colorado trans with the 60° inpur shaft, bell housing and tourque converter. I needed to get both trannys ayway so its just a little more work than expected to adapt it
You won't need the Colo valvebidy just the pan and filter. The bell is gonna have to be from a 60* v6 or 4cylinder. The I5 and L6 engines are different than the v6. The L6 has the starter hump in a different location and I assume the I5 does as well not to mention the bolt pattern to block is different.
Buddrow
If it don't fit force it, if it don't force fit f&%@ it!
Bookmarks