AutoProm ADC Interface Channels Set up in TunerPro!

[EagleMark]

Are there other errors in the log of other parameters that match in time with those errors?

What he said...

Did the adx file work without glitch before this? What adx?

[T2000]

I certainly havent noticed the glitch or error in other logged data... certainly not the usual suspects anyway (RPM,MAP,TPS,SPARK etc)

The XDF and ADX is OSE_12P which if you are interested is documented in detail here: http://delcohacking.net/forums/viewtopic.php?f=27&t=356

I have attached the complete OSE_12P package which has the XDF & ADX.
OSE12P can be run on any '808, '165 or '3082 ECM & supports 2-8 cyl.

I run my own variation of the 1BAR Petrol ADX which gives me different dash's and the WB (I'm at work atm so dont have access to it)


I would be interested to know your theories in the meantime. You question re other errant data at the same point in time... indicative of something which you have seen before?

For the purpose of my previous experiment the APU1 was not connected to the ECM at all! I isolated the APU1 and just fed a known voltage to the ADC.

Thanks for your time gents

[EagleMark]

We have our first tester of this and it works on dash board as I showed above. But it is not showing up in data log?

[EagleMark]

The XDF and ADX is OSE_12P which if you are interested is documented in detail here: http://delcohacking.net/forums/viewtopic.php?f=27&t=356

I have attached the complete OSE_12P package which has the XDF & ADX.
OSE12P can be run on any '808, '165 or '3082 ECM & supports 2-8 cyl.

I run my own variation of the 1BAR Petrol ADX which gives me different dash's and the WB (I'm at work atm so dont have access to it)


I would be interested to know your theories in the meantime. You question re other errant data at the same point in time... indicative of something which you have seen before?

For the purpose of my previous experiment the APU1 was not connected to the ECM at all! I isolated the APU1 and just fed a known voltage to the ADC.

Thanks for your time gents

Probably interesting read, but what is this for? Which of the adx files did you use from that zip?

[T2000]

Probably interesting read, but what is this for? Which of the adx files did you use from that zip?

"OSE_$12PV111_1BAR - Petrol.adx"
&
"OSE12P V111 - 1,2 and 3 bar.xdf"


& I have tried both (on separate vehicles):

"OSE $12P V111 APNX V6.bin"
"OSE $12P V111 BLCF V8.bin"

Currently testing on Australian GM (Holden) vehicles with '808 ECM's and Buick v6 and Holden v8


It is almost as if the Offset has some how changed between packets and then reverts back ??? if that makes sense?

Cheers, Chris

[EagleMark]

Your not from this side of the pond are you?

I got it on my list to look at in AM. Got no experiance with these but will see if I notice something that may be affecting it.

Right now the big issue is this works on dash board but does not save in data log xdl file?

[T2000]

Your not from this side of the pond are you?

I got it on my list to look at in AM. Got no experiance with these but will see if I notice something that may be affecting it.

Right now the big issue is this works on dash board but does not save in data log xdl file?

Yeah last time I looked there is a big ditch full of water right between my place & your place

Strange I am sure that my attempts at WB02 and ADC1/2/3 logging saved in the xdl file.

I will confirm asap as that might help you to track the problem.

Thanks again for your efforts,


Regards, Chris

[EagleMark]

I have not had any luck getting the data showing to be in log but have only been working on a 160 Baud on test bench, works fine just can't get it in log?

Do you have the ADX with the AutoProm stuff installed? the files you had above in Zip don't seem to? This glitch I have not found, always solid data in dash, wish was in log...

[wsherrard]

I may have missed it and this may be a dumb question but... is all this the same for the LM-2?