Results 1 to 4 of 4

Thread: Advice on how to disable TCC lockup vs TPS on 7060 PCM

  1. #1
    Electronic Ignition!
    Join Date
    Feb 2013
    Posts
    19

    Advice on how to disable TCC lockup vs TPS on 7060 PCM

    I'm looking for some advice on how to disable the TCC at say above 80% TPS... I see in the XDF I have there is a Torque Converter Release/Engage vs TPS table which seems to be triggered off MPH, however the highest I can set it is to 127.5mph. I've seen other threads saying that it may be possible to set it to 255mph but whenever I enter that number in it defaults back to 127.5mph.

    I'm using the stock 7060 PCM to control a 4L80E trans, however its powered by a blown big block 540 at the moment, so I'm anticipating I may have a trap speed of >127MPH in the 1/4mi so I'd rather not risk having the TCC lockup under that sort of power.

    Any suggestions on how I disable the TCC lockup under a certain threshold (that's above 127mph or >%80 TPS?).. Would setting it to 0 mph disable the TCC at those parameters?

  2. #2
    Super Moderator dave w's Avatar
    Join Date
    Feb 2011
    Posts
    6,264
    Bluecat Transmission Table Software could be helpful with TCC Tuning: https://forum.hptuners.com/showthrea...Table-Software

    dave w

  3. #3
    Electronic Ignition!
    Join Date
    Feb 2013
    Posts
    19
    Quote Originally Posted by dave w View Post
    Bluecat Transmission Table Software could be helpful with TCC Tuning: https://forum.hptuners.com/showthrea...Table-Software

    dave w

    Thanks! Ya I have the bluecat software and have been using it successfully. The issue seems to stem from a limitation of the "127.5mph" deal as bluecat tells me basically to enter 255mph for certain WOT thresholds, however for some reason when I enter that in tunerpro it changes it to 127mph ??? I'm sure it stems from the fact this is an older PCM and perhaps that's a limitation of it (?)

    Unless anyone has any suggestions on how to do this in the tune, I could always interrupt the brake pedal switch for the TCC when doing a WOT run via a switch I suppose..

  4. #4
    Super Moderator dave w's Avatar
    Join Date
    Feb 2011
    Posts
    6,264
    In the link listed below shows a factory TH400 Kickdown switch. The kickdown switch can be wired through a 5 pin relay to interrupt TCC power at WOT.

    http://www.gearhead-efi.com/Fuel-Inj...ll=1#post23185

    dave w

Similar Threads

  1. Lockup control e-13 on 16197427
    By bar0403 in forum GM EFI Systems
    Replies: 2
    Last Post: 08-28-2018, 01:43 AM
  2. Question on TC Lockup with 94 454
    By kevinvinv in forum GM EFI Systems
    Replies: 1
    Last Post: 10-26-2016, 09:38 PM
  3. 700R4 Lockup Control w/ TBI
    By matt2491 in forum GM EFI Systems
    Replies: 64
    Last Post: 07-14-2015, 01:00 AM
  4. TCC lockup delay
    By damanx in forum GM EFI Systems
    Replies: 1
    Last Post: 04-01-2015, 03:23 PM
  5. 4L80E+decel lockup
    By gregs78cam in forum GM EFI Systems
    Replies: 1
    Last Post: 08-05-2011, 06:29 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •