Bringing TBI and Multi Port Fuel Injection to a New Level.     EFI Conversions and Tuning! Seattle to Portland! E-mail Tuning Consultant!
Results 1 to 8 of 8

Thread: Injectors pulsing when engine is OFF?!

  1. #1
    Fuel Injected! CDeeZ's Avatar
    Join Date
    May 2012
    Location
    Jokelahoma
    Posts
    364

    Injectors pulsing when engine is OFF?!

    I built a pretty stout TBI and have not been able to work the bugs out until recently.... The engine will start easy and idle well and have good throttle response some times.... But other times it won't start, or if it does it is hard to start and runs poorly......

    I recently discovered that with the KEY ON but ENGINE OFF, you can open the throttle and the injectors go crazy and start pulsing..... That can't be right..... THe oil has gasoline in it and the one plug I pulled out was wet with gasoline.......

    At the 5:50 mark of this video you can hear that the engine starts right up and idles well and has good throttle response....... So the video shows what this thing SHOULD be like........ Then randomly without warning, it runs poorly..... I'm thinking the plugs being wet must be the problem and I'm also thinking the problem must stem from the issue I describe with the fuel injectors........ Anyone got any insight into this?

    https://www.youtube.com/watch?v=RBFBryKSTYs

  2. #2
    Administrator
    Join Date
    May 2011
    Location
    Lakes Region, NH
    Age
    49
    Posts
    2,989
    I have never seen nor heard of that. IMO there should be an RPM signal before that pulsing occurs. Custom code or a setting that was incorrectly changed? Possible loose memcal? Hard to say if the connection between this and the good/bad running just might be related.

  3. #3
    Fuel Injected! CDeeZ's Avatar
    Join Date
    May 2012
    Location
    Jokelahoma
    Posts
    364
    Yeah me either. It has me stumped. No custom code, at least that I'm aware of lol. If I EVER find the cause, I will post back with the cause. Everything else checks out so I really don't know.

  4. #4
    Administrator
    Join Date
    May 2011
    Location
    Lakes Region, NH
    Age
    49
    Posts
    2,989
    I installed a used 7427 into my truck a couple of years ago that whould show MAP sensor fluctuations of 15-20 kPa on the scantool during KOEO. The voltages at the sensor and at the ecm were steady. I put it in a pile of "fix me someday" ecm's and installed another.

  5. #5
    Fuel Injected! CDeeZ's Avatar
    Join Date
    May 2012
    Location
    Jokelahoma
    Posts
    364
    Did that make the MAP issue on the scantool go away? I will drag out another one of my 7427s and slap it in there.

  6. #6
    Administrator
    Join Date
    May 2011
    Location
    Lakes Region, NH
    Age
    49
    Posts
    2,989
    Yes. After swapping PCM's the scantool MAP reading behaved and the engine stopped surging.

  7. #7
    Fuel Injected!
    Join Date
    Sep 2012
    Location
    Huntsville, AL
    Posts
    124
    I once worked on an LT1 that had a bad wiring harness between the cam position sensor (optispark for you LT1 guys) and the computer. Just breathe on the wire and the injectors would all pulse and the ignition coil would start firing. We replaced the harness and the problem went away. Just my experience. But I'd try a PCM too.

  8. #8
    Fuel Injected! CDeeZ's Avatar
    Join Date
    May 2012
    Location
    Jokelahoma
    Posts
    364
    Thinking it was the PCM.... Was a junkyard find that probably got submerged in rain for a few months/years before I found it. Stabbed another JY 7427 in there and the weirdness seems gone.... For now....

Similar Threads

  1. 7747 TCC Signal Pulsing-700r4 Converter Will Not Lock
    By Opas69 in forum GM EFI Systems
    Replies: 1
    Last Post: 07-06-2018, 09:37 AM
  2. AE pulsing in DFCO
    By JeepsAndGuns in forum GM EFI Systems
    Replies: 11
    Last Post: 02-23-2014, 05:26 PM
  3. Injectors not pulsing...
    By mytmouz in forum GM EFI Systems
    Replies: 9
    Last Post: 01-06-2014, 12:43 AM
  4. Engine Dyno ? Fast 102 Intake MAF and 36 lb injectors
    By EagleMark in forum OBDII Tuning
    Replies: 27
    Last Post: 11-19-2013, 12:30 AM
  5. Replies: 8
    Last Post: 04-25-2012, 08:36 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •