Page 2 of 2 FirstFirst 12
Results 16 to 23 of 23

Thread: red devil blue tooth problem

  1. #16
    Fuel Injected! MQQN28's Avatar
    Join Date
    May 2016
    Location
    Melbourne Australia
    Age
    76
    Posts
    65
    Dom

    Try this adx file and see if it works.
    With ALDL Droid when you press connect ECU button it switches the 10k resistor and the data stream should start. The blue led will be flashing and then change to green yel/red.
    If ALDL droid indicates no data stream check if the CEL light is flashing , probably look like it is full on. This will tell you if the data stream has at least started.
    If this works your data may be a bit off due to this file, but we just want to see if the data stream starts.
    If this doesn't work it may be another problem other than the ADX file or both.


    Dom
    sorry I put up the wrong file. I will change it and put the right one up in the morning.

    MOC
    Attached Files Attached Files
    Last edited by MQQN28; 09-07-2017 at 12:36 AM.
    Ford 28 Roadster Pick Up
    Ford Flathead 51 8BA. Balanced, ported,3/4 cam, Edelbrock 59A heads, C4 trans, 8" diff 3.55 narrowed 40mm /side.
    Fuel injection by Flatattack racing, 60mm Holden TB.
    ECM Delco 1227808 160 baud.

  2. #17
    Fuel Injected! MQQN28's Avatar
    Join Date
    May 2016
    Location
    Melbourne Australia
    Age
    76
    Posts
    65
    Dom

    try this one. Sorry about that busy day

    MOC
    Attached Files Attached Files
    Ford 28 Roadster Pick Up
    Ford Flathead 51 8BA. Balanced, ported,3/4 cam, Edelbrock 59A heads, C4 trans, 8" diff 3.55 narrowed 40mm /side.
    Fuel injection by Flatattack racing, 60mm Holden TB.
    ECM Delco 1227808 160 baud.

  3. #18
    Fuel Injected!
    Join Date
    Apr 2015
    Location
    Albuquerque, NM
    Posts
    52
    I tried the 2nd file witch has the correct ECM number and I get a [connected waiting for ECM data] message. Never gets data.
    1993 Chevy Blazer TBI Vortec long block 5.7
    16168625 BDJZ 46mm TB 18 PSI fuel
    Camshaft, Hydraulic Roller Tappet, Advertised Duration 288/308, Lift .431/.451
    Chevrolet Performance Vortec TBI Intake Manifold
    shorty's, y-pipe and 3" full boar muffler

  4. #19
    Fuel Injected! MQQN28's Avatar
    Join Date
    May 2016
    Location
    Melbourne Australia
    Age
    76
    Posts
    65
    Dom

    Maybe back to basics

    It's either the sensor state is not sending the message or the unit is not seeing the data.

    Check pins A eth, B sensor, M 8192 data, G the blue tooth powers from this. This tag is fuel pump power
    Is pin M actually in the right spot in the ALDL socket. When you get the message not seeing data is the CEL light flashing. If no the data has not started, if yes the data pin M is a problem.

    I did read some where in the instructions from red devil that you may have to start the data by manually putting the 10k resistor in. This is a nuisance but if the data starts and works you know where you are. When working properly you connect the leds flash, press connect ECU the blue flashes then the other colors flash it connects and the data starts.

    MOC
    Ford 28 Roadster Pick Up
    Ford Flathead 51 8BA. Balanced, ported,3/4 cam, Edelbrock 59A heads, C4 trans, 8" diff 3.55 narrowed 40mm /side.
    Fuel injection by Flatattack racing, 60mm Holden TB.
    ECM Delco 1227808 160 baud.

  5. #20
    Fuel Injected!
    Join Date
    Apr 2015
    Location
    Albuquerque, NM
    Posts
    52
    just tried and now not even Tuner Pro RT is not working.
    1993 Chevy Blazer TBI Vortec long block 5.7
    16168625 BDJZ 46mm TB 18 PSI fuel
    Camshaft, Hydraulic Roller Tappet, Advertised Duration 288/308, Lift .431/.451
    Chevrolet Performance Vortec TBI Intake Manifold
    shorty's, y-pipe and 3" full boar muffler

  6. #21
    Fuel Injected! MQQN28's Avatar
    Join Date
    May 2016
    Location
    Melbourne Australia
    Age
    76
    Posts
    65
    Are you using the original ADX file for tuner pro?
    Ford 28 Roadster Pick Up
    Ford Flathead 51 8BA. Balanced, ported,3/4 cam, Edelbrock 59A heads, C4 trans, 8" diff 3.55 narrowed 40mm /side.
    Fuel injection by Flatattack racing, 60mm Holden TB.
    ECM Delco 1227808 160 baud.

  7. #22
    Fuel Injected!
    Join Date
    Apr 2015
    Location
    Albuquerque, NM
    Posts
    52
    Thank You MQQN28
    I am giving up. I need to install an WB O2 sensor with gauge I can monitor that plus tune.
    1993 Chevy Blazer TBI Vortec long block 5.7
    16168625 BDJZ 46mm TB 18 PSI fuel
    Camshaft, Hydraulic Roller Tappet, Advertised Duration 288/308, Lift .431/.451
    Chevrolet Performance Vortec TBI Intake Manifold
    shorty's, y-pipe and 3" full boar muffler

  8. #23
    Fuel Injected! MQQN28's Avatar
    Join Date
    May 2016
    Location
    Melbourne Australia
    Age
    76
    Posts
    65
    Dom
    Sorry to hear that. I know mine was a battle at times but I got it, your initial query got me going again.
    I'm at adjusting the ADX file at the moment but a little transmission problem has sidelined me. I will see the transmission man on the way home today.

    When that problem is fixed I will be asking questions also.

    MOC
    Ford 28 Roadster Pick Up
    Ford Flathead 51 8BA. Balanced, ported,3/4 cam, Edelbrock 59A heads, C4 trans, 8" diff 3.55 narrowed 40mm /side.
    Fuel injection by Flatattack racing, 60mm Holden TB.
    ECM Delco 1227808 160 baud.

Similar Threads

  1. Looking for a disassembly of 12613246 OS Green Blue PCM
    By james_adams2006 in forum GM EFI Systems
    Replies: 5
    Last Post: 02-19-2021, 04:51 PM
  2. 7730 ecm 40 tooth tone ring
    By misterpat in forum GM EFI Systems
    Replies: 9
    Last Post: 05-13-2017, 03:04 AM
  3. Red/blue connectors
    By myburb in forum GM EFI Systems
    Replies: 0
    Last Post: 10-17-2015, 04:56 AM
  4. 40 tooth vss sensor gap/clearance
    By JeepsAndGuns in forum Gear Heads
    Replies: 7
    Last Post: 01-07-2015, 03:11 AM
  5. Strange issue using red devil river and aldl droid
    By davidgoodin in forum GM EFI Systems
    Replies: 11
    Last Post: 11-21-2014, 03:35 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •