Results 1 to 10 of 10

Thread: 7730 ecm 40 tooth tone ring

  1. #1
    Fuel Injected!
    Join Date
    Mar 2015
    Age
    48
    Posts
    26

    7730 ecm 40 tooth tone ring

    Hi all!

    Finally getting to the point of hooking all my fuel injection up. I started a previous thread on here about feeding a Jeep speedometer and the tpi ecm with the same sender.

    http://www.gearhead-efi.com/Fuel-Inj...R4-VSS-Options

    I decided to go a different route and do a full custom dash. So I can get a speedometer that will work with whatever I got.

    Now my question about feeding the ecm with the vss i got.

    With a 37" tire and 5.38 gears, my driveshaft will spin 3055.84 times a mile. Which will make 122233.6 pulses per mile.

    Looking through the ANJF bin in TunerPro RT in the scalars section on the bottom is Vehicle Speed Sensor. In there I can set the ppm to 115200 which is close.

    But will the ecm be able to use this type of input? I've been googling it, but no yes or no answer.

    vss.jpg

  2. #2
    Administrator
    Join Date
    May 2011
    Location
    Lakes Region, NH
    Age
    54
    Posts
    3,847
    What type of pulses are being supplied by the VSS? A/C or D/C? The 115200 value will work with an A/C sensor. The rules change with a D/C signal.

  3. #3
    Fuel Injected!
    Join Date
    Mar 2015
    Age
    48
    Posts
    26
    I think it is A/C. The sender I have is a DORMAN 917-616 which was used in many GM vehicles from 88 through 05 it looks according to rockauto's site.

  4. #4
    Administrator
    Join Date
    May 2011
    Location
    Lakes Region, NH
    Age
    54
    Posts
    3,847
    Yes, that's A/C.

  5. #5
    Fuel Injected!
    Join Date
    Mar 2015
    Age
    48
    Posts
    26
    Now I'm wondering. If this will work, but only be close, not right. Would I just be better off running a drac?

    EDIT:

    Can I even use a drac with the 7730 ecm? It outputs square wave, correct?
    Last edited by misterpat; 05-09-2017 at 03:28 AM.

  6. #6
    Super Moderator
    Join Date
    Mar 2011
    Location
    Camden, MI
    Age
    35
    Posts
    3,026
    you can feed a 7730 a square wave VSS signal, just need to move the VSS input wire to a different pin and change a flag. AFAIK, every mask run on the 7730 supports the "optical" VSS input.
    1995 Chevrolet Monte Carlo LS 3100 + 4T60E


  7. #7
    Fuel Injected!
    Join Date
    Mar 2015
    Age
    48
    Posts
    26
    Sounds easy enough. Anyone know what pin is for the square wave input?

    So I got this straight.

    1. Repin the VSS input to ??
    2. Re-jumper the drac for my proper multiplier.
    3. Change my bin to use the square wave input "optical" at 4000ppm.

    Correct?

    Thanks!

  8. #8
    Administrator
    Join Date
    May 2011
    Location
    Lakes Region, NH
    Age
    54
    Posts
    3,847
    Yes. Pin C6. Set up the DRAC to produce 2000 pulse per mile. Clear the "magnetic VSS present" bit 6 @ 0x0018. The speed sensor pulse per mile divider will no longer be used.

  9. #9
    Fuel Injected!
    Join Date
    Mar 2015
    Age
    48
    Posts
    26
    Awesome, Thanks! So once that "magnetic VSS present" is cleared, the "Road Speed Constant" at 0x15 is irrelevant? Or does it need to be set to 2000ppm as done here:

    http://www.gearhead-efi.com/Fuel-Inj...-on-a-7730-ECM
    Last edited by misterpat; 05-13-2017 at 02:27 AM.

  10. #10
    Administrator
    Join Date
    May 2011
    Location
    Lakes Region, NH
    Age
    54
    Posts
    3,847
    The RSS affects the signal sent from the ecm to the instrument cluster.

Similar Threads

  1. Need a little 7730, S_AUJP, LC-1 help please.
    By Dewayne_S in forum GM EFI Systems
    Replies: 3
    Last Post: 09-15-2016, 05:28 AM
  2. TCC Lock w/saw-tooth tach input [7060 or 7427]
    By dubwise in forum GM EFI Systems
    Replies: 4
    Last Post: 03-11-2015, 05:54 AM
  3. 40 tooth vss sensor gap/clearance
    By JeepsAndGuns in forum Gear Heads
    Replies: 7
    Last Post: 01-07-2015, 03:11 AM
  4. '7730 ECM - Pin F8 Question
    By 84Elky in forum GM EFI Systems
    Replies: 10
    Last Post: 11-18-2013, 09:50 PM
  5. 40-toothed VSS tone-wheel
    By romac55 in forum GM EFI Systems
    Replies: 2
    Last Post: 06-28-2012, 06:28 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •