Hi,
You should probably start with copying injector flow, offset and short pulse compensation tables from stock 3.4 bin. Tuning injectors with measured AFR is not the best way...
Hi,
You should probably start with copying injector flow, offset and short pulse compensation tables from stock 3.4 bin. Tuning injectors with measured AFR is not the best way...
Hello
problem is actually that I cannot find the injector pulse tables at first sight in the XDF file I have.......
can I assume that all the bin files for the different engines that use the 1227730 ECU have them on the same location in the memory chip?
grtz, D
Hello
Is there someone who can set me on the right track.....
I was expecting to simply find a table map/RPM/injector time and TPS/RPM/injector time, like on a lot of other programs I worked with....
Seems like this setup is using volumetric efficiency, to determine the volume of air in the cilinders, and calculate how much fuel must be added....
I already found the value for the flow rate of the injectors
I am probable looking wrong, but for now I am searching for a value to change the volume of each cilinder (for the bigger engine: 3.1 => 3.4 )
I presume If that is adjusted, I will need to change the VE values, until the desired AFR is reached without adjustments of the ECM
Is that correct?
grtz, D
hello
maybe I was a little bit too fast with my prevoius questions ...
Done a lot of reading here on the forum and elsewhere on the internet, and I think I am a step further now....
For the moment, I am still using te AZTY bin from gearefi, together with the 88 mask complete 1.01 from Robert Saar, and the 88ADX.
Entered the correct flowrate of the injectors in the bin (18 lb/hr) (KDISFS).
The flowrate for Alpha-N seems not possible to be changed, but I guess that is not an issue for now.. (It resets every time to 0.16)
Made some historytables (BLM vs RPM vs MAP)
After running some log files, notice that the BLM is somewhere between 100 and 110, but it changes a lot...
Could this be by the bigger volume of the engine?
What value should I opprox add to the VE table for lets say each value of 5 that is short in the BLM?
grtz, D
Hello
Got the fuel ok by now bit by bit...
First the low throttle, now started to the higher throttle...
Almost all the BLM's between 126 and 130....
Noticed that when I go full throttle, the ecm goes into open loop....
Could someone tell me if it is possible to add conditions to the history tables....
That way, I could ignore the values when goes out of closed loop.....
Searched for it on this forum and on the internet, but didn't find any of this.....
And one more question, but the car did this since I got it... (even with the 3.1 engine)
When the engine is hot, it somethimes struggle to get it started....
Seems like I hear a little 'ping' sometimes too....
Advance is pre-set to 10°, starter engine is new, and also the cable from the battery to the starter is new..
Battery is good.
Only this that stays the same is the distributor... (cap and rotor is new, cables and plugs also new)
So I guess I could narrow it to the ignition module....
Could this be faulty? What should be the other symptoms then?
grtz, D
@ Robert...
You mentioned before that you switched to $A1
I believe that is to use the DIS-system correct?
Could you tell me what cables I have to reconnect/change to use the DIS?
grtz, D
any of the MPFI 60V6 masks will run DIS or a distributor pretty easily, I think only 3 values need changed in the calibration. as far as wiring, I've never had to do it, all of mine have been DIS already, but it can't be more than the couple of wires that run to the ICMs. they use the same signaling scheme over 4 wires (EST, EST bypass, 3X high, 3X low) that connect to the ECM.
Bookmarks