94-95 $EE xdf (EEXTRA)

[dzidaV8]

Here's my updated EEXTRA, maybe you'll find something new in it :) I have added some parameters for evaporator temperature sensor and A/C low charge.

[jthompson122183]

Here's my updated EEXTRA, maybe you'll find something new in it :) I have added some parameters for evaporator temperature sensor and A/C low charge.

Thank you for the contribution to the xdf. Ill have it added in with credit for source of information.

[jthompson122183]

@Kur4o

Do you have any updated ida diss files?

[kur4o]

These are the most recent I have.
I am still trying to list all the different operating systems used on 96-97 bins.
I got some bins from the forum, but still far from complete list.

[jthompson122183]

I am still trying to list all the different operating systems used on 96-97 bins.

here is a list of 96-97 cal ids supported by tunercat vdf.

[jthompson122183]

I got some bins from the forum, but still far from complete list.

add another to your list

[jthompson122183]

@Kur4o

You must be popular, your inbox is full.

[kur4o]

You can try now. I always forget to clear some space.

[jthompson122183]

OP updated with V0.002

a bunch of auto trans related stuff has been labeled. It's massive!! Over 1mb!!

[kevinodb1]

Hi there,

Good to see some works being done on 96 vehicles.

I have a 94 Vette Manual using EEHACK and a 1996 Grandsport Manual using LT1Edit(Hmmm), Having been tuning them both for some time now and have raced both.

I have tried looking at definitions 002 and the latest vsn 3.2 but Tunerpro sais I dont have a late enough version even though I have downloaded the latest one? works ok with 001.

I also have a question on the 12df2 End Of Injection Target Table. I am assuming when it says TDC it is meaning on the firing stroke not the induction stroke?

6 degrees would seem to be a bad value to still be injecting, for a sequential system, because the intake valve is already closed, does anyone have any thoughts on this?

It would seem at high duty cycles that the 94 or 96 LT's sequential injection is more or less constant anyway...

As a comparison a Lucas Mechanical Injection System on a Triumph TR6 or 2500 PI times the Injector to start 20-45 degrees ATDC on the induction stroke, a Cosworth DFV is 30 Degrees ATDC and a Cosworth BDG is 80 ATDC Degrees. These systems have a very fast total injection time that only spans 52 degrees crank(Triumph 6 cylinders) So all the fuel is well on its way in plenty of time before the intake valve closes.

I am curious to know if anyone has tried different values in the table which at low pulse widths would at least affect the idle!?


Cheers and happy 2018!

Kevin
Wellington
New Zealand

[jthompson122183]

I have tried looking at definitions 002 and the latest vsn 3.2 but Tunerpro sais I dont have a late enough version even though I have downloaded the latest one? works ok with 001.

latest tunerpro version is 5.00.9130.00 ive uploaded a new version of eextra to the OP see if that works.

[jthompson122183]

ive added v0.003 to the OP, fixed some e-side locations per dzidav8 information from another thread.

[jthompson122183]

the End of injection table if from the TC definition


Capture2.JPG




i dont have specifics related to this pcm, maybe @Kur4o will post what he has learned.


here is some info ive found about injector timing

https://www.hptuners.com/forum/showt...njector-Timing

https://www.hptuners.com/forum/showt...ight=injection

[kevinodb1]

the End of injection table if from the TC definition


Capture2.JPG

Yes thats the same values as a 1994 Y car manual in Tunerpro, but Tunerpro has a "DEG SPK BTDC" label which may not be correct if its for INJ...

Ive got the new version of Tunerpro working now by reinstalling and rebooting TNX.

Cheers
Kevin

Kevin

[jthompson122183]

Yes thats the same values as a 1994 Y car manual in Tunerpro, but Tunerpro has a "DEG SPK BTDC" label which may not be correct if its for INJ...

Ive got the new version of Tunerpro working now by reinstalling and rebooting TNX.

Cheers
Kevin

Kevin

that was labeling mistake, its taking care of now.

i dont know what TC is referring to "Location" is. From reading those links i would say its some kind of offset before the injector is fired?