Results 1 to 13 of 13

Thread: New guy with 3400

  1. #1
    Fuel Injected!
    Join Date
    Jul 2016
    Age
    62
    Posts
    52

    New guy with 3400

    I have converted a fwd 3400 to rwd and using an ecm from a 93 camaro. 16172693. Not really wanting to get into tuning but I would like be able to plug in and see whats going on. I have downloaded Tuner pro and looked it over, do I need a bin file, XDF and ADX just to see the encine parameters?

  2. #2
    Fuel Injected! mmigacz's Avatar
    Join Date
    Oct 2013
    Location
    Sheboygan Falls, WI
    Age
    50
    Posts
    161
    Quote Originally Posted by dbuster View Post
    I have converted a fwd 3400 to rwd and using an ecm from a 93 camaro. 16172693. Not really wanting to get into tuning but I would like be able to plug in and see whats going on. I have downloaded Tuner pro and looked it over, do I need a bin file, XDF and ADX just to see the encine parameters?
    Yes, you will need to download the XDF, ADX and a starter bin. This tread would be helpful http://www.gearhead-efi.com/Fuel-Inj...rmation-P66-V6
    1986 ski centurion boat, 351W, gt40P heads, edelbrock performer rpm, 1227747 ecm, 72 lb/hr injectors (@18 PSI fuel pressure), .490/.490 lift, intake 278 duration, exhuast 282 duration, 112 lobe separation

    1969 camaro, 355ci, performer RPM intake, camel hump heads, 1227747 ecm, 454 throttle body (@18 PSI fuel pressure),

    2016 Chevy Cruz

    2014 Chevy Silverado

  3. #3
    Fuel Injected!
    Join Date
    Jul 2016
    Age
    62
    Posts
    52
    Thanks, I have those down loaded. Says the XDF covers all revision 3 bins but not 93 F bodys which is what I have. I am still in the early stages of this project, would I be better off using a different ECM?

  4. #4
    Super Moderator
    Join Date
    Mar 2011
    Location
    Camden, MI
    Age
    35
    Posts
    3,026
    running a manual or automatic? if manual, you should be able to use a 94-95 calibration without any changes that I know of.

    if you have an automatic, you're looking at a very one-off situation.... the XDF that would be needed is specific only to the 93 3.4 calibration, which I didn't create due to every other 3.4/3100 application being covered by a single XDF.
    1995 Chevrolet Monte Carlo LS 3100 + 4T60E


  5. #5
    Fuel Injected!
    Join Date
    Jul 2016
    Age
    62
    Posts
    52
    I will be running a manual trans but I'm not sure what trans was in the donor car, I think it may have been an auto. Thanks for the response.

  6. #6
    Super Moderator
    Join Date
    Mar 2011
    Location
    Camden, MI
    Age
    35
    Posts
    3,026
    donor car won't really matter if you're going to run a manual. you SHOULD be able to upload a 94-95 manual calibration into the 93 PCM, but if not, you'll need to pick up any 94-95 3100/3.4RWD PCM and upload a manual calibration into it.

    since it's sounding like you're doing a transplant, you'll need to disable or workaround VATS and other little things that likely aren't in your destination car.
    1995 Chevrolet Monte Carlo LS 3100 + 4T60E


  7. #7
    Fuel Injected!
    Join Date
    Jul 2016
    Age
    62
    Posts
    52
    Thanks, I'll give it a try. The way I understand VATS controls fuel pump operation, my car (79 MGB) has an electric fuel pump so I plan on using that circuit to control the new fuel pump.

  8. #8
    Fuel Injected!
    Join Date
    Jul 2016
    Age
    62
    Posts
    52
    Ok it's been awhile, not sure if I should have started a new post or continue this one. I was able to to down load an XDF , ADX and a bin that would work for me. back in Feb. or march I had the PCM programed to remove VATS (it controls more than the fuel pump) EGR and other uneeded items. I finally have everything installed and running, on three cylinders! The injectors for cylinders 3,4 and 5 are are not receiving a ground from the pcm. I have checked the wiring and see no problems. Not sure where to go from here, is there anything I should check before replacing the pcm.

  9. #9
    Fuel Injected!
    Join Date
    Jun 2015
    Age
    36
    Posts
    354
    check the connector at the back of the intake, it may be open circuit.

  10. #10
    Fuel Injected!
    Join Date
    Jul 2016
    Age
    62
    Posts
    52
    Thanks, circuit is good from pcm to injectors. I can ground each injector at the pcm plug and they all actuate.

  11. #11
    Fuel Injected!
    Join Date
    Jul 2014
    Posts
    5
    Quote Originally Posted by dbuster View Post
    Thanks, I have no idea what this says.
    Gibberish... Forum has been spammed by a bunch of these.

  12. #12
    Fuel Injected!
    Join Date
    Jan 2013
    Age
    77
    Posts
    132
    It seems the site has been hacked. It maybe that the responses have been translated into French phrases/language.

  13. #13
    Super Moderator Six_Shooter's Avatar
    Join Date
    Feb 2011
    Posts
    2,968
    Not hacked, just spam. It's been removed.
    The man who says something is impossible, is usually interrupted by the man doing it.

Similar Threads

  1. V6 3400 vs 3800
    By NISANDA in forum Other EFI systems and related topics
    Replies: 1
    Last Post: 02-27-2014, 10:06 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •