Need help with my tuner pro

**Jwathen23** · 10-10-2015

Hey guys I finally got my ostrich 2.0 in the mail to tune my truck since I've put a marine intake and vortec heads on it... I'm on tuner pro rt and have my proper ald xds and bin files. But my blms at idle to about 1500 rpm are 140.. and I can't for the life of me find the ve tables or any fueling tables for that matter.. can someone please help.. I'm a newbie this is my first attempt at tuning

**buddrow** · 10-10-2015

What ecm/bin/adx are you using? In Tunerpro, there are parameter trees that pull down to display the deciphered calibration settings. The tall narrow box on the left of the screen, double click on an item and it should expand listing parameters, scalars, etc.

Buddrow

**Jwathen23** · 10-11-2015

Ok so I found the ve tables.. must of been tired last night... my bin is bjdr 94 c-g-k truck 5.7tbi 4l80e.bin XDF file E6_TPV5_v250.XDF adx file is A201_E6_v250.adx.... now I'm trying to tune my spark tables and I've heard you do it through knock counts.. well my knock counts read 24136.. somethings not right here.. can someone explain?

**Roadknee** · 10-11-2015

There's a little more to setting up timing tables than looking at knock counts. If the knock counts are rising during a given engine operation you may have too much timing in that area. However, knock counts do not necessarily mean you have too much timing. Several of us have encountered "false knock" with these TBI trucks and have disabled knock retard altogether.

Vortec heads require more timing than the TBI swirlports. I've attached a screenshot of a modified vortec timing table in a TBI truck I've had good luck with. It should be a good starting point for you. This particular engine is 10:1 and tickled the knock sensor at 1200-1600 rpm above about 60 kpa. Your engine might tolerate a little more timing in that area. Copy the same values into the idle spark table.

Zero out your PE spark as shown in the screenshot and if your marine intake deleted EGR, disable the EGR as shown too.

**Jwathen23** · 10-11-2015

Thanks man I'll try it out I'm the process of fooling with it now .. after I get the timing tables down will I have to fine tune the ve tables again?

**Jwathen23** · 10-11-2015

And also what's the best way to adjust the timing tables?.. here in a weeks I'm going to have a mild cam for it and I'd like to know the best ways to get this thing figured out.. it's a lot harder then I thought it was..

**Fast355** · 10-11-2015

Originally Posted by Roadknee

There's a little more to setting up timing tables than looking at knock counts. If the knock counts are rising during a given engine operation you may have too much timing in that area. However, knock counts do not necessarily mean you have too much timing. Several of us have encountered "false knock" with these TBI trucks and have disabled knock retard altogether.

Vortec heads require more timing than the TBI swirlports. I've attached a screenshot of a modified vortec timing table in a TBI truck I've had good luck with. It should be a good starting point for you. This particular engine is 10:1 and tickled the knock sensor at 1200-1600 rpm above about 60 kpa. Your engine might tolerate a little more timing in that area. Copy the same values into the idle spark table.

Zero out your PE spark as shown in the screenshot and if your marine intake deleted EGR, disable the EGR as shown too.

I do not like Zero'ing out the PE spark. There is good reason to keep it, especially if you keep the stock PE entry and delays. This is what I was running in a L31 suburban with long tubes and a F-car LT1 cam.

**Jwathen23** · 10-11-2015

Apparently I don't belong programing this thing.. I mean I know how a motor works I know everu thing about them.. I'm a dirt track racer and I'll tell you no computer is alot easier this this!! Trying to tune my ve tables now and can't get nothing to run right... I still have a retard knock of 9.5... can't figure out how to turn it off... I think I'll have a beer and try again in the morning