Page 6 of 11 FirstFirst 1234567891011 LastLast
Results 76 to 90 of 156

Thread: Another option for $0D efan control

  1. #76
    RIP EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    63
    Posts
    10,477
    Quote Originally Posted by PJG1173 View Post
    I'll try again this afternoon. I'm connecting the positive lead from my volt meter to the cigarete outlet is there somewhere else I should be connecting?
    The cigarette/cigar/power outlet is an iffy place for a power source since the positive lead is center of bottom of socket and barrel is ground. Maybe find a dedicated source from fuse box...

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  2. #77
    Vintage Methane Ejector
    Join Date
    Apr 2011
    Posts
    194
    If you have the relays wired-up then just connect them. Double check to see if your on the correct pin.

  3. #78
    Fuel Injected! PJG1173's Avatar
    Join Date
    Nov 2011
    Location
    Jacksonville NC
    Age
    50
    Posts
    641
    would it matter that i am running a 16168625 that was previously running $e6?
    87 4Runner, 15" spring lift, 3" body, chevy vortec 355, 5.29 gears, 38.5x15.5x15" Boggers, 280hr, 16168625 running $0D
    93 S10, 36x12.5x15 TSL's, custom turbo headers, 266HR cam, p&p vortec heads, $0D Marine MPFI with 8psi boost.
    05 Silverado, 2' lift, 4" exhaust, Bully Dog programmer,

  4. #79
    Vintage Methane Ejector
    Join Date
    Apr 2011
    Posts
    194
    Not that I know of, but if need be, I can swap mine out for a 8625 and load your bin. Not gonna happen today though, it would be several days before I had time.

  5. #80
    Fuel Injected! PJG1173's Avatar
    Join Date
    Nov 2011
    Location
    Jacksonville NC
    Age
    50
    Posts
    641
    Quote Originally Posted by 93V8S10 View Post
    Not that I know of, but if need be, I can swap mine out for a 8625 and load your bin. Not gonna happen today though, it would be several days before I had time.
    I'm fixing to go out and wire in a couple lights the ecu and do some more testing. It was getting too cold last night to do the wiring.
    87 4Runner, 15" spring lift, 3" body, chevy vortec 355, 5.29 gears, 38.5x15.5x15" Boggers, 280hr, 16168625 running $0D
    93 S10, 36x12.5x15 TSL's, custom turbo headers, 266HR cam, p&p vortec heads, $0D Marine MPFI with 8psi boost.
    05 Silverado, 2' lift, 4" exhaust, Bully Dog programmer,

  6. #81
    Fuel Injected! PJG1173's Avatar
    Join Date
    Nov 2011
    Location
    Jacksonville NC
    Age
    50
    Posts
    641
    looks like my volt meter must not had enough resistance or something. it appears to be working with the relay hooked up.
    87 4Runner, 15" spring lift, 3" body, chevy vortec 355, 5.29 gears, 38.5x15.5x15" Boggers, 280hr, 16168625 running $0D
    93 S10, 36x12.5x15 TSL's, custom turbo headers, 266HR cam, p&p vortec heads, $0D Marine MPFI with 8psi boost.
    05 Silverado, 2' lift, 4" exhaust, Bully Dog programmer,

  7. #82
    Vintage Methane Ejector
    Join Date
    Apr 2011
    Posts
    194

  8. #83
    Fuel Injected! one92rs's Avatar
    Join Date
    Apr 2011
    Posts
    173
    now that is what i want to hear. glad you have it working. let us know the progress as i want to use the schematic i posted and have the ecm run the fans, engine, and the 60e.

  9. #84
    Vintage Methane Ejector
    Join Date
    Apr 2011
    Posts
    194
    Quote Originally Posted by one92rs View Post
    now that is what i want to hear. glad you have it working. let us know the progress as i want to use the schematic i posted and have the ecm run the fans, engine, and the 60e.
    With yours C1 will go to E3 (Fan A), this will be high speed with both fans running. Connect C2 to E7 (Fan B), this will be low speed with just the right fan running.

    If you want to use the soft start for high speed, then replace the Cool Fan 1 Relay with the Hella solid state relay. The relay connections will be like this:
    wire B1 to pin 86
    wire C3 don't use
    connect pin 85 to ground
    wire B3 to pin 30
    wire C1 to pin 87
    Last edited by 93V8S10; 02-27-2012 at 03:01 AM.

  10. #85
    Fuel Injected! one92rs's Avatar
    Join Date
    Apr 2011
    Posts
    173
    Quote Originally Posted by 93V8S10 View Post
    With yours C1 will go to E3 (Fan A), this will be high speed with both fans running. Connect C2 to E7 (Fan B), this will be low speed with just the right fan running.

    If you want to use the soft start for high speed, then replace the Cool Fan 1 Relay with the Hella solid state relay. The relay connections will be like this:
    wire B1 to pin 86
    wire C3 don't use
    connect pin 85 to ground
    wire B3 to pin 30
    wire C1 to pin 87
    you are the man. i have this saved to my camaro info folder. man i love this sight. but one question. in the diagram i posted when the first relay (or temp threshold is reached the fans come on low) the first relay hits the power on both fans but there is a croosover wire that causes them to run on about 50%, then when both relays ( second temp threshold is reached) both fans come on high. so will these grounds from the ecm come on consecutively, or is it one or the other.
    Last edited by one92rs; 02-27-2012 at 03:28 AM.

  11. #86
    Fuel Injected! PJG1173's Avatar
    Join Date
    Nov 2011
    Location
    Jacksonville NC
    Age
    50
    Posts
    641
    93V8S10 you are the man! this works great! I've attached how I wired everything up.
    Attached Images Attached Images
    87 4Runner, 15" spring lift, 3" body, chevy vortec 355, 5.29 gears, 38.5x15.5x15" Boggers, 280hr, 16168625 running $0D
    93 S10, 36x12.5x15 TSL's, custom turbo headers, 266HR cam, p&p vortec heads, $0D Marine MPFI with 8psi boost.
    05 Silverado, 2' lift, 4" exhaust, Bully Dog programmer,

  12. #87
    Vintage Methane Ejector
    Join Date
    Apr 2011
    Posts
    194
    Quote Originally Posted by one92rs View Post
    you are the man. i have this saved to my camaro info folder. man i love this sight. but one question. in the diagram i posted when the first relay (or temp threshold is reached the fans come on low) the first relay hits the power on both fans but there is a croosover wire that causes them to run on about 50%, then when both relays ( second temp threshold is reached) both fans come on high. so will these grounds from the ecm come on consecutively, or is it one or the other.
    They will come on consecutively, but you need to keep in mind that this code may not work the same as the original code. You will need to play around with is some if you want to try and match the original operation. You may be able to achieve something similar with creative use of the different parameters. Your options are all open, with one exception, if you want to use the soft start then you have to use the solid state relay in the Cool Fan 1 Relay position, controlled with Fan A.

  13. #88
    Vintage Methane Ejector
    Join Date
    Apr 2011
    Posts
    194
    PJG1173

    Thanks! I'm glad you got it working!

    I'm gonna steal your's and one92rs's schematics!

  14. #89
    Administrator
    Join Date
    May 2011
    Location
    Lakes Region, NH
    Age
    54
    Posts
    3,847
    Because the coolant flows through engine, out the back of the manifold, through the heater core, through the radiator, and finally back to pump, until the thermostat opens.
    This return provides the fastest warmup. Returning to radiator pulls even colder water into block. I have buses with oversized dual heaters so I have dealt with slow and poor warmup for years. OEM solution for mid '80s and '90s engines with aluminum wet flow intakes was to put heater connection in rear of manifold and ensure restrictors in intake gaskets covered rear coolant ports (coolant had to run from front of intake to rear before exiting) and to use heater outlet fitting with restrictor. I've brazed 3/8" washers to heater outlet fittings in the past to reduce coolant flow out of block. But if your intake gaskets are allowing coolant to enter manifold from rear of heads you'll never see proper warming.

  15. #90
    Fuel Injected!
    Join Date
    May 2011
    Location
    Pocono's PA.
    Age
    50
    Posts
    370
    Quote Originally Posted by 93V8S10 View Post
    Got the expanded fan code done for $E6 and $0D, $0E/$31 to come later. This should be able to run a wide variety of set-ups. I have tested the $0D for basic function, I'll leave the final testing up to you guys. Let me know if you find any problem and if you like/hate it. If you'll like it, then it may find it's way into the Advance v275.xdf.

    Enjoy:
    O.K , I give up , I typed all of the HEX included in the code above into the Hex editor in T/P for my .bin . How do I get the functions included in the fan control XDF that 93V8S10 provided to show up in my bin on the T/P parameter tree ?

    Am I just missing something ?

    Thanks

    TOM
    1994 3500 Dually , 502 (509) , 264HR , Edelbrock MPFI , PFI '7427
    1992 S-10 434 SBC/Tremec - '7427
    1986 Monte Carlo SS
    1984 S-10 , SAS, 496/700R4/205 , D44/14BFF -'7427
    1980 Z-28 496/700R4
    1979 Corvette 496/700R4
    1977 Olds 98 Regency 403/700R4

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •