Results 1 to 8 of 8

Thread: 95 F-body Fuel Pump with 95 B-Body Engine/Tank

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Carb and Points!
    Join Date
    Apr 2015
    Posts
    4

    95 F-body Fuel Pump with 95 B-Body Engine/Tank

    I'm new to this forum, but was hoping for some help from the experts here.
    I'm building a 37 Buick Roadmaster using a 95 Roadmaster LT1 donor car.
    Looks like I can fit the 95 Fuel tank, but I would like to upgrade the fuel pump.
    From pictures on the internet, it appears the B-body fuel pump does not have a return line that feeds into pump can. (See 1st picture).
    Have read that it is recommended to keep B-body gas tank 1/3 full to keep fuel pump cool.
    The F-body fuel pump appears to have return line feed into the pump can which would cool the pump. (See 2nd picture)
    1) Can anyone confirm that these pictures are typical of the fuel pumps found on these cars?
    2) Does the F-body gas just spill out of the top after it is forced into the pump can?
    3) Does anyone know if I could swap put the B-body pump assy for a F-body?
    Thanks

  2. #2
    Super Moderator Six_Shooter's Avatar
    Join Date
    Feb 2011
    Posts
    2,968
    There's 3 lines on that B-body pump assembly picture, feed, vent and return. I'm not sure what the 4th line on the F-body pump assembly is for, other than being an additional vent possibly.

    IIRC, the return tube on the Body assembly is also support for the pump, where that spring is wrapped around in the picture. This is common, to get the return end down into the fuel to eliminate or at least reduce aeration, and reduce parts cost. Using the return tube to also support the pump is just clever engineering.
    The man who says something is impossible, is usually interrupted by the man doing it.

  3. #3
    Carb and Points!
    Join Date
    Apr 2015
    Posts
    4
    Quote Originally Posted by Six_Shooter View Post
    There's 3 lines on that B-body pump assembly picture, feed, vent and return. I'm not sure what the 4th line on the F-body pump assembly is for, other than being an additional vent possibly.

    IIRC, the return tube on the Body assembly is also support for the pump, where that spring is wrapped around in the picture. This is common, to get the return end down into the fuel to eliminate or at least reduce aeration, and reduce parts cost. Using the return tube to also support the pump is just clever engineering.
    1) So on the B-body the return fuel goes down the tube into the can?

    2) Does it then spill out of the top of the can?

    Thanks

  4. #4
    Super Moderator Six_Shooter's Avatar
    Join Date
    Feb 2011
    Posts
    2,968
    I don't recall the details of the B-Body assembly specifically, but some will fill the pump reservoir (too make sure it stays full even at low fuel levels), some will pour out under it.
    The man who says something is impossible, is usually interrupted by the man doing it.

  5. #5
    Carb and Points!
    Join Date
    Apr 2015
    Posts
    4
    Quote Originally Posted by Six_Shooter View Post
    I don't recall the details of the B-Body assembly specifically, but some will fill the pump reservoir (too make sure it stays full even at low fuel levels), some will pour out under it.
    Thanks fro your help.

  6. #6
    Fuel Injected!
    Join Date
    Oct 2013
    Posts
    1,022
    The return by itself won't fill the canister since any fuel that comes out of the return had to "leak" into the fuel pump area. You're simply looking at a baffled tank. A fuel pump canister with a little hose coming off the pump uses it to feed a venturi that actually does fill the canister.

Similar Threads

  1. LT4 HOTCAM 93 F BODY BIN
    By MYLTWON in forum TunerPro Tuning Talk
    Replies: 2
    Last Post: 11-22-2013, 08:44 AM
  2. holley throttle body
    By bonnieclyde100 in forum Introductions
    Replies: 12
    Last Post: 03-22-2013, 10:21 AM
  3. W-body(?) pinout for 1227727?
    By dyeager535 in forum GM EFI Systems
    Replies: 23
    Last Post: 07-19-2012, 07:28 AM
  4. GM body list
    By historystamp in forum Gear Heads
    Replies: 18
    Last Post: 01-26-2012, 10:25 PM
  5. MPI throttle body options
    By JeepsAndGuns in forum GM EFI Systems
    Replies: 43
    Last Post: 01-19-2012, 03:57 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •