I would suspect that putting the 87 parts onto the engine and then use the ownership from that truck and the visual proof of the swap in the completed motorhome would get you the approval as a EFI transplant.
Once that far, changing the PCM and add the transmission later. I expect they just do a visual of the engine smog equipment and a tailpipe sniff.
Almost finished stripping the TBI parts off the Suburban.
Di I need the fuel pipes that come up to the TB?
I'd keep them, the ends at the tb are hard to duplicate. You can always shorten them later.
If it has the braided lines then definitely keep em. They're hard to find.
68 Cadillac, 472 & TH400 w/7.4L TBI and EBL **sold**
93 K1500 short step, 5.7 & NV4500 and EBL
68 C10 LQ4/TKO swapped
The fuel lines can be made, however, they use a special fitting that GM liked to use them (It's called a Sawginaw fitting). Usually this requires fairly expensive flaring tools to make this fitting. Mine cost me about $350 on a deal. So you may want to pull the lines and have them handy to use.
On the flip side many parts stores sell "repair ends" with these fittings and can be used in a swap situation like this. They come in various lengths from 6" to 18".
The man who says something is impossible, is usually interrupted by the man doing it.
Good info, I will pull them if I can.
So, I am taking the TBI unit, Harness(marked every wire or left parts attached), sensors, Air filter, air injection setup(not the exhaust manifolds), smog pump, EGR, pipes and valves.
I managed to remove the whole TBI setup, except the coolant pipe that comes out of the back of the TBI unit... could not budge the fitting and could not release the hard pipe from the back of the head, so I cut it.
Removed the whole front accessories setup inc pulleys, alternator, smog pump, AC compressor, and brackets.
Chased all of the wiring thru the firewall on the pass side and released it from the ECU and pulled it back thru the firewall cleanly. Took the ECU out.
Could not get the wires out from the ECU to ALDL out, so I cut them each end as long as I could. I think I would have to lengthen that anyway.
Couple of questions...
Should I remove the Knock sensors? There looks to be 2...
I removed the harness as far as the fuse block on the drivers side firewall... how do I release that, or can I cut it off????
1994 3500 Dually , 502 (509) , 264HR , Edelbrock MPFI , PFI '7427
1992 S-10 434 SBC/Tremec - '7427
1986 Monte Carlo SS
1984 S-10 , SAS, 496/700R4/205 , D44/14BFF -'7427
1980 Z-28 496/700R4
1979 Corvette 496/700R4
1977 Olds 98 Regency 403/700R4
So, am in the ongoing march toward the TBI/4L80E swap.
Was at the Junkyard on halfprice day, and grabbed this... for $18...
16197427 BJYL ecu and about as much wiring as I could reach from a "95 Suburban.
Did I get the right one... a TBI/4L80E controller?
Will this run a 454 TBI from 1987/1990?
I know I will need more stuff, like the plug for the 4L80E too, but I was looking for the DRAC, and could not find it!
Where is teh DRAC???
Do you already have the 4L80e? The '91-93 is a bit different than the later versions and should be used with the '7060 ECM, any others would use the'7427 you grabbed. It's much easier to start with a complete 4l80e harness to rework rather than trying to build it from scratch.
1973 K-5 Blazer, TBI 350, TH400, 1 ton axles & 38" SSRs'
1975 280Z, TBI 350, 700R4
1953 M-38A1, TBI Buick 231
1951 Ford Panel, 5.3 with 4L80E
I have the 4l80E, but i do not know what year it is... see my original post on page 1.
I am aware of the "Force Motor" difference, so will keep that in mind when I rebuild it.
So what's the difference in the force motor that would cause one to need to change to a different PCM?
The man who says something is impossible, is usually interrupted by the man doing it.
I forgot that you're here in California. As suggested earlier, it's probably best to go with the '7747 setup with the original trans to get it though the referee as an engine swap. Once you've jumped those hurdles, you can go back and swap in the '7427 and 4L80E.
1973 K-5 Blazer, TBI 350, TH400, 1 ton axles & 38" SSRs'
1975 280Z, TBI 350, 700R4
1953 M-38A1, TBI Buick 231
1951 Ford Panel, 5.3 with 4L80E
Bookmarks