Troubles starting up with Ostrich 2.0

[trippyjoey]

So I was installing the Ostrich 2.0 on my 95 TBI, I have the right bin, mask, everything and I tried turning the truck on but I got no spark. I disconnected the ostrich 2.0 from my laptop and tried to start it and it runs but if I try datalogging it just says "DA Connecting" and it never connects. If I plug the ostrich 2.0 While it's running the truck turns off. I removed the Ostrich 2.0 and installed my memcal back in there and it runs fine and I can Datalog

I'm stuck here any suggestions?

[Six_Shooter]

This may seem like a silly question, but I've seen people miss this step in the past.

Have you uploaded the bin to the Ostrich?

[dave w]

I'll start with the basics:
The attached pictures show how the Ostrich 2.0 is correctly installed with a Moates.net G1 adapter into the PCM.

Are we good so far?

dave w

[trippyjoey]

I've correctly installed the the ostrich 2.0 to the g1 adapter with Memcal attached then secured it to the ecm until the clips clicked. I did upload a new bin and I noticed right away the difference cause the new bin had the PE and DFCO turned off but as I said it would only run if the usb from the ostrich wasn't connected to my laptop.

[trippyjoey]

And I did change the mask ID to AA

[Six_Shooter]

Ok, so it's the USB that needs to be disconnected, that wasn't clear in your first post. It sounded to me like it was the ribbon cable that was being disconnected, which would allow LHM (Limp Home Mode) to run the engine.

That's an issue I have not seen.

Have you tried turning emulation on or off and see any difference in running?

[trippyjoey]

I did and I can't start the truck as long as the usb is connected to the laptop even if the turn the emulation on or off
I'm gonna try getting an older driver from moates and trying again in a bit once the rain calms down.

[dave w]

I've correctly installed the the ostrich 2.0 to the g1 adapter with Memcal attached then secured it to the ecm until the clips clicked. I did upload a new bin and I noticed right away the difference cause the new bin had the PE and DFCO turned off but as I said it would only run if the usb from the ostrich wasn't connected to my laptop.

Ok, Just checking. I just found an additional picture I wanted to put in my first post. I think it's possible someone in the future might find the pics helpful.

I've used the Ostrich 2.0 "stand alone" (not connected to a Laptop) countless times. Maybe try using the Ostrich 2.0 stand alone?

dave w

[Six_Shooter]

The only thing that comes to mind is a com port conflict, where two programs are trying to access the same port when you connect the Ostrich via USB.

You could try manually changing the com port assigned to the Ostrich.

[trippyjoey]

I don't mind using it but still I need to be able to catalog and I can't right now.

[Six_Shooter]

If you can't datalog that means that the truck is in LHM.

Just to make sure: You do have a separate datalogging cable, correct? The Ostrich does not have a datalogging feature. There is a hit tracing feature, but that is a different animal.

[trippyjoey]

If you can't datalog that means that the truck is in LHM.

Just to make sure: You do have a separate datalogging cable, correct? The Ostrich does not have a datalogging feature. There is a hit tracing feature, but that is a different animal.

I do have a separate datalogging cable, what is LHM?

[buddrow]

LHM is Limp Home Mode. It runs a default code to get you home, or somewhere safe, in case of PROM error.

Buddrow

[trippyjoey]

Well I feel stupid now............. I rechecked my connections and noticed I put the ostrich 2.0 on the adapter backwards

It's running perfect now. Thanks everyone.

[buddrow]

I wasn't trying to belittle you. no need to feel stupid. :)

Buddrow