Results 1 to 6 of 6

Thread: Lean hesitation with cold engine TBI

  1. #1
    Fuel Injected!
    Join Date
    May 2014
    Posts
    23

    Lean hesitation with cold engine TBI

    Guys I need help with a lean hesitation, for a tbi 305. Has 081 tpi heads, lt1 cam and some other mods. Runs good when started cold till the temp gauge gets to about 140 degrees then hesitates. Once warmed up to 200 degrees runs good again. I get a hesitation when accelerating the more throttle the bigger the hesitation. I have the fuel pressure and blms tuned close to ideal. What table should I adjust to get rid of that hesitation. I am using a painless harness and 7747 ecm.

  2. #2
    Fuel Injected!
    Join Date
    Feb 2013
    Location
    DFW, TX
    Posts
    2,393
    Quote Originally Posted by 92TBIVentura View Post
    Guys I need help with a lean hesitation, for a tbi 305. Has 081 tpi heads, lt1 cam and some other mods. Runs good when started cold till the temp gauge gets to about 140 degrees then hesitates. Once warmed up to 200 degrees runs good again. I get a hesitation when accelerating the more throttle the bigger the hesitation. I have the fuel pressure and blms tuned close to ideal. What table should I adjust to get rid of that hesitation. I am using a painless harness and 7747 ecm.
    The TBI head tunes run a good bit leaner than the TPI head tunes through warmup despite being TBI. Might add some fuel to the coolant temp vs MAP table in the temperature range you are experiencing issues in. Also might need more MAP and TPS AE in those coolant temperature ranges. Is it in open or closed loop when this happens?

  3. #3
    RIP EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    64
    Posts
    10,477
    At those temps it's probably not a fuel table and it's Closed loop by then. As Fast mentioned it may be AE TPS and AE MAP.

    One thing that helps and some people still overlook Stoich AFR! With E fuel it's 14.12 and when we had none E fuel it's 14.7... this is all it takes for a lean warm up issue!

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  4. #4
    Fuel Injected!
    Join Date
    May 2014
    Posts
    23
    I have a 3 wire o2 sensor on it, so probably closed loop, unless there are some other factors involved for it to go closed loop. Thanks for the reply

  5. #5
    Fuel Injected!
    Join Date
    May 2014
    Posts
    23
    I am running gas with 10 percent ethanol that is what is available mostly unless you get premium at some stations. I'll try bumping up those ae map & ae tps values. Should I start with one or do both at the same time? Thank You

  6. #6
    LT1 specialist steveo's Avatar
    Join Date
    Aug 2013
    Posts
    4,081
    if you dont have a stoich setting for it to go off of, you can just bump your injector constant or base injector whateverthehell, its pretty much the same, that's what i did with EE.

    drives me nuts trying to get it close here on any vehicle, i have a variation of 0% to 15% ethanol in our local pump gas, which is fine if im near home (i've determined which station is 0% in the premium pump), but if i fill up somewhere else i can feel the difference.

    only real solution is to run it a bit rich and just let 'er trim for cruising economy when its running 0%. it's not like it minds a bit of extra fuel in other situations anyway.

Similar Threads

  1. Engine temp vs Engine efficiency
    By sciroc in forum GM EFI Systems
    Replies: 2
    Last Post: 05-17-2014, 02:51 AM
  2. Replies: 9
    Last Post: 03-21-2014, 07:13 AM
  3. 7165 ECM only communicates when cold
    By eseibel67 in forum GM EFI Systems
    Replies: 1
    Last Post: 05-05-2013, 05:34 PM
  4. Replies: 3
    Last Post: 07-28-2012, 05:10 AM
  5. Looking for Nitrous Engine Damage on LS1 engine?
    By EagleMark in forum Gear Heads
    Replies: 11
    Last Post: 07-26-2012, 06:22 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •