Bringing TBI and Multi Port Fuel Injection to a New Level.     EFI Conversions and Tuning! Seattle to Portland! E-mail Tuning Consultant!
Results 1 to 14 of 14

Thread: 16188051 and 16181333 PCM Information $EE $EEB

  1. #1
    EFI GearHead ! EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    57
    Posts
    10,477

    16188051 and 16181333 PCM Information $EE $EEB

    16188051 and 16181333 PCM Information $EE was used in the 1994 - 1995 Y, F, B car and Cadillac 5.7L, LT1.

    $EEB was called Rev B and used in a few early 1994 vehicles

    *Work in Progress*

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  2. #2
    EFI GearHead ! EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    57
    Posts
    10,477

    1994 16188051 PCM Wiring diagrams.

    1994 16188051 PCM Wiring diagrams.
    Attached Images Attached Images

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  3. #3
    EFI GearHead ! EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    57
    Posts
    10,477

    1995 16188051 PCM Wiring diagrams.

    1995 16188051 PCM Wiring diagrams.
    Attached Images Attached Images

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  4. #4
    EFI GearHead ! EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    57
    Posts
    10,477

    1994 and 1995 95 5.7L Error Codes for 16188051 PCM used in LT1 engines.

    94-95 OBD I LT1 DTCs
    DTC 11 - Malfunction Indicator Lamp (MIL) Circuit
    DTC 13 - Bank I (Left) Heated Oxygen Sensor (HO2S) Circuit (Open Circuit)
    DTC 14 - Engine Coolant Temperature (ECT) Sensor Circuit ( Voltage Low, High Temp)
    DTC 15 - Engine Coolant Temperature (ECT) Sensor Circuit ( Voltage High, Low Temp)
    DTC 16 - Distributor Ignition System (Low Resolution Pulse)
    DTC 18 - Injector Circuit(s)
    DTC 21 - Throttle Position (TP) Sensor Circuit (Signal Voltage High)
    DTC 22 - Throttle Position (TP) Sensor Circuit (Signal Voltage Low)
    DTC 23 - Intake Air Temperature (IAT) Sensor Circuit ( Voltage High, Low Temp)
    DTC 24 - Vehicle Speed Sensor (VSS) Circuit
    DTC 25 - Intake Air Temperature (IAT) Sensor Circuit ( Voltage Low, High Temp)
    DTC 26 - Evaporative Emission (EVAP) Canister Purge Solenoid Valve Circuit
    DTC 27 - Exhaust Gas Recirculation (EGR) Vacuum Control Signal Solenoid Valve Circuit
    DTC 28 - Transmission Range (TR) Pressure Switch Assembly Fault
    DTC 29 - Secondary Air Injection (AIR) Pump Circuit
    DTC 32 - Exhaust Gas Recirculation (EGR)
    DTC 33 - Manifold Absolute Pressure (MAP) Sensor Circuit ( Voltage High - Low Vacuum)
    DTC 34 - Manifold Absolute Pressure (MAP) Sensor Circuit ( Voltage Low - High Vacuum)
    DTC 36 - Distributor Ignition System (Faulty High Res. or Extra Low Res. Pulse Detected)
    DTC 37 - Brake Switch Stuck "ON
    DTC 38 - Brake Switch Stuck "OFF
    DTC 41 - Ignition Control (IC) Circuit (Open Circuit)
    DTC 42 - Ignition Control (IC) Circuit (Shorted or Grounded Circuit)
    DTC 43 - Knock Sensor (KS) Circuit
    DTC 44 - Bank 1 (Left) Heated Oxygen Sensor (HO2S) Circuit (Lean Exhaust Indicated)
    DTC 45 - Bank 1 (Left) Heated Oxygen.Sensor (HO2S) Circuit (Rich Exhaust Indicated)
    DTC 46 - PASS-Key Circuit
    DTC 47 - Knock Sensor (KS) Circuit or Module Missing
    DTC 48 - Mass Air Flow (MAF) Sensor Circuit
    DTC 50 - System Voltage Low
    DTC 51 - EEPROM Programming Error
    DTC 53 - System Voltage High
    DTC 55 - Fuel Lean Monitor
    DTC 58 - Transmission Fluid Temperature (TFT) Sensor Circuit Low (High Temp )
    DTC 59 - Transmission Fluid Temperature (Low Temperature Indicated)
    DTC 61 - A/C System Performance
    DTC 63 - Bank 2 (Right) Heated Oxygen Sensor (HO2S) Circuit (Open Circuit)
    DTC 64 - Bank 2 (Right) Heated Oxygen Sensor (HO2S) Circuit (Lean Exhaust Indicated)
    DTC 65 - Bank 2 (Right) Heated Oxygen Sensor (HO2S) Circuit (Rich Exhaust Indicated)
    DTC 66 - A/C Refrigerant Pressure Sensor Circuit (Open or Shorted)
    DTC 67 - A/C Refrigerant Pressure Sensor Circuit (Pressure Sensor Activity)
    DTC 68 - A/C Relay Circuit (Shorted Circuit)
    DTC 69 - A/C Clutch Circuit
    DTC 70 - A/C Clutch Relay Driver Circuit
    DTC 71 - A/C Evaporator Temperature Sensor Circuit
    DTC 72 - Vehicle Speed Sensor Loss
    DTC 73 - Pressure Control Solenoid (PCS) Circuit (Current Error)
    DTC 74 - Traction Control System(TCS)CircuitLow
    DTC 75 - Transmission System Voltage Low
    DTC 77 - Cooling Fan Relay Control Circuit
    DTC 78 - Fan control PCM terminal A10
    DTC 79 - Transmission Fluid Overtemp
    DTC 80 - Transmission Component slipping
    DTC 81 - Transmission 2- 3 Shift Solenoid Circuit
    DTC 82 - Transmission 1-2 Shift Solenoid Circuit
    DTC 83 - Reverse Inhibit System (Manual Transmission) <<<<<<<<<select>>>>>>
    DTC 83 - TCC/PWM (Auto Trans)
    DTC 84 - Automatic Transmission 3-2 Control Solenoid Circuit <<<select>>>>>>
    DTC 84 - Skip Shift Solenoid Circuit (Manual Transmission Only)
    DTC 85 - Transmission TCC Stuck "ON
    DTC 90 - Transmission TCC Solenoid Circuit
    DTC 91 - Skip Shift Lamp Circuit
    DTC 97 - VSS Output Circuit
    DTC 99 - Tach Output Circuit

    ---------------------------------------

    GM
    1994 and 1995 95 5.7L Error Codes for 16188051 PCM used in LT1 engines.

    NOTE: This is a complete list. Not all are specific for each car. There may be more or less depending on vehicle like Corvette, Camaro, Firebird, Impala SS, Caprice and RoadMaster that came with the LT1 engine

    11 Malfunction indicator lamp circuit voltage was wrong for 26 seconds.
    13 Oxygen sensor voltage stays between 0.35 and 0.55 volts for 60 seconds. Engine was at normal operating temperature and had been running for at least 2 minutes after start with a throttle angle above 5%.
    14 Coolant temperature sensor signal indicates a temperature of over 284 F.
    15 Coolant temperature sensor signal indicates a temperature colder than -40 F.
    16 A low resolution pulse was not detected by ECM within 720 high resolution timing pulses.
    18 Injector driver circuit voltage to PCM was wrong for 4 seconds.
    21 TPS voltage was above 2.5 volts for 3 seconds when the engine was running, or when the TPS was above 4.8 volts at any time.
    22 TPS voltage was under 0.23 volts when the engine was running.
    23 Inlet air temperature sensor signal showed an air temperature below -31 F for 60 seconds after the engine has been running for 4 minutes.
    24 Vehicle speed was 0 MPH when engine speed was between 900 and 3000 RPM and throttle position angle was less than 2% for 5 seconds.
    25 Inlet air temperature sensor signal showed an air temperature over 302 F for 12 seconds after the engine has been running for 4 minutes.
    26 ECM detected the wrong potential voltage at the #1 quad-driver module circuit for 20 seconds.
    27 ECM detected the wrong potential voltage at the #2 quad-driver module circuit for 3 seconds.
    28 ECM detected the wrong potential voltage at the #3 quad-driver module circuit for 3 seconds.
    29 Secondary air injection pump circuit voltage was wrong for 26 seconds.
    32 EGR open command did not change the fuel mixture when the command was given during off idle operation. EGR opening should cause the mixture to be slightly richer because of the low oxygen content of the exhaust gas.
    33 MAP sensor signal voltage was too high (low vacuum) for 1 second when throttle opening was under 20% and engine speed was above 1250 RPM.
    34 MAP sensor signal voltage was too low (high vacuum) when engine speed was under 700 RPM, or when TPS was greater than 20% with an engine speed above 700 RPM.
    36 ECM detected less than 40 high resolution timing pulses between each low resolution pulse for 5 consecutive cycles.
    41 EST circuit voltage was above 4.6 volts when engine speed was under 1500 RPM.
    42 PCM did not detect any EST signal within 84 crankshaft revolutions.
    43 One or both of the knock sensors were either open or grounded for 5 seconds.
    44 Left oxygen sensor voltage was under 0.2 volts for 50 seconds of closed loop operation.
    45 Left oxygen sensor voltage was over 0.7 volts for 50 seconds when the throttle angle was above 4% during closed loop operation.
    47 Knock sensor signal was not present.
    48 There was no MAF signal when engine was on.
    50 PCM detected an ignition voltage of less than 8.0 volts.
    51 PROM error.
    52 Engine oil temperature was below -31 F after engine had been running for 30 minutes.
    53 ECM detected a battery voltage above 17.1 volts.
    55 ECM detected a lean oxygen sensor voltage for 8 seconds during the power enrichment modes of operation.
    62 Engine oil temperature sensor indicated an oil temperature above 284 F after engine had been running for 30 minutes.
    63 Right oxygen sensor was open showing a steady voltage between 0.35 and 0.55 volts for 60 seconds after the engine had been running for at least 2 minutes with a throttle angle above 5%.
    64 Right oxygen sensor voltage was below 0.2 volts for 50 seconds of closed loop operation.
    65 Right oxygen sensor voltage was above 0.7 volts for 50 seconds of closed loop operation when the throttle angle was above 4%.
    66 A/C pressure sensor circuit was either open or shorted showing a voltage below 0.12 volts or above 4.86 volts for 10 seconds.
    67 ECM did not detect an A/C system pressure change of more than 9 psi when A/C clutch was engaged.
    68 ECM detects voltage on the A/C status line for more than 20 seconds after ECM has disengaged the A/C relay.
    69 ECM did not detect any voltage on A/C status line for 20 seconds after ECM had commanded A/C ON.
    70 A/C clutch relay circuit showed incorrect potential voltage at PCM for 26 seconds.
    72 Transmission output speed changed more than 1000 RPM for 2 seconds when vehicle was in gear, or transmission output speed changed more than 2048 RPM when vehicle was in park or neutral.
    73 Pressure control solenoid return amperage was more than 0.16 amp different than the commanded amperage for 1 second.
    74 Traction control system active signal input was 0 volts for more than 2 seconds when vehicle was in park or neutral.
    75 Ignition voltage was less than set value for 4 seconds when engine speed was above 1000 RPM.
    77 Cooling fan relay #1 control potential voltage at PCM was incorrect for 26 seconds.
    78 Cooling fan relay #2 and #3 control potential voltage at PCM was incorrect for 26 seconds.
    79 Transmission fluid temperature signal indicated a temperature higher than 295 F for 30 minutes, or higher than 306 F at any time.
    81 Transmission 2-3 shift solenoid voltage stayed high for 2 seconds after commanded ON by PCM, or the voltage stayed at zero for 2 seconds after commanded OFF by PCM.
    82 Transmission 1-2 shift solenoid voltage stayed high for 2 seconds after commanded ON by PCM, or the voltage stayed at zero for 2 seconds after commanded OFF by PCM.
    83 TCC PWM solenoid voltage stayed high for 2 seconds after commanded ON by PCM, or the voltage stayed at zero for 2 seconds after commanded OFF by PCM.
    84 Transmission 3-2 shift solenoid voltage stayed high for 5 seconds after commanded ON by PCM, or the voltage stayed at zero for 5 seconds after commanded OFF by PCM.
    85 TCC solenoid remained ON for 4 seconds after commanded OFF by PCM 90 TCC solenoid voltage stayed high for 2 seconds after commanded ON by PCM, or the voltage stayed at zero for 2 seconds after commanded OFF by PCM.
    91 One to Four up-shift lamp control signal showed incorrect potential voltage at PCM for 26 seconds.
    97 VSS output signal showed incorrect potential voltage at PCM for 26 seconds.
    98 Tach output signal showed incorrect potential voltage at PCM for 26 seconds.

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  5. #5
    EFI GearHead ! EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    57
    Posts
    10,477

    $EE Hack

    Disassembly of $EE
    Attached Files Attached Files

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  6. #6
    EFI GearHead ! EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    57
    Posts
    10,477

    LT1 Bin Files

    Here's a collection of LT1 bin files for 1994 and 1995.

    94 vs. 95 code

    If you install 95 code in a 94 you need to disable DTC 83 and copy over the TCC apply/release rate tables from your old bin.
    Attached Files Attached Files

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  7. #7
    EFI GearHead ! EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    57
    Posts
    10,477

    LT1 Bin Files

    Here's a few more
    Attached Files Attached Files

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  8. #8
    EFI GearHead ! EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    57
    Posts
    10,477

    WOT BLM Locker for LT1

    WOT BLM Locker for LT1. This little program locks BLM to 128 at WOT with the 1994 and 1995 LT1 engines. I have run this on a chip and tested and it does just that. Then adjust your WOT AFR up 20% and your right about 12.9 to 1 AFR. Made a big difference in my car!
    Attached Files Attached Files

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  9. #9
    EFI GearHead ! EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    57
    Posts
    10,477

    LT1 Speedometer Calibration for tire and gear change to tune PCM!

    Two tools.

    Spreadsheets to use with Data logging BLM in tunerPro for BLM VE tables in Open Office and Microsoft Excel.

    MPH calculator, here's a little tool to calculate the right numbers to enter into your bin file if you have changed tires and gears on a $EE 1994 1995 and been told it's the same for OBDII 1996 1997 LT1 engines but have not checked that myself. It does work for OBDI !
    Attached Files Attached Files

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  10. #10
    EFI GearHead ! EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    57
    Posts
    10,477

    TunerPro $EE adx and XDF Improved versions

    steveo has taken on the $EE mask and improving the TunerPro RT XDF file. Great work!
    http://www.gearhead-efi.com/Fuel-Inj...223-new-EE-xdf

    It is recommeded that this XDF file is used. All data tracing is still in tact for use with $EE-16188051-V3.8.adx

    Until they are completer here is a link to where the latest files will be at:
    http://resfilter.net/files/carstuff/...DF_CURRENT.zip
    Thanks for sharing your work steveo!


    The ADX and XDF files below was built from scratch and a much improved version then what was available which also work on B body cars as well as F and Y body. Some people get a bad connection first time. I have tried this on three cars and found the same thing. Disconnect and second connection is always good solid data. If I can work this problem out I will update ADX file.

    The V3 files or higher version work together for Data Tracing as well in TunerPro V5 RT

    EEB.xdf is for early 1994 Rev B chips which are very rare. You can reflash PCM with newer bin if you want? It is recommended to reflash using an $EE file.
    Attached Files Attached Files

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  11. #11
    Super Moderator
    Join Date
    Mar 2011
    Location
    Camden, MI
    Age
    28
    Posts
    3,021
    and since it's been asked multiple times, this seems like a good place for it.

    http://www.gearhead-efi.com/Fuel-Inj...for-95-LT1-PCM

    blue/gray = T-side
    red/black = E-side
    1995 Chevrolet Monte Carlo LS 3100 + 4T60E


  12. #12
    Banned
    Join Date
    Aug 2013
    Age
    48
    Posts
    219

    1994 Calibration ID's

    Mark you can move these and delete this thread is you would like.

    EDIT EagleMark:Thanks AJ! I just moved the post here to $EE info thread.

    1994 Camaro 1


    1994 Camaro 2


    1994 Camaro 3


    1994 Camaro 4


    1994 Camaro 5


    1994 Camaro 6


    1994 Firebird 1


    1994 Firebird 2



    1994 Firebird 3



    1994 BL


    1994 BN


    1994 DW


    EDIT EagleMark: Added Calibration ID spreadsheet!
    Attached Files Attached Files
    Last edited by Caleditor; 01-29-2014 at 09:25 AM.

  13. #13
    EFI GearHead ! EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    57
    Posts
    10,477
    $EE Ve SpreadSheet by Dave W.
    Attached Files Attached Files

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  14. #14
    Super Moderator
    Join Date
    Mar 2011
    Location
    Camden, MI
    Age
    28
    Posts
    3,021
    Steveo's updated EE BIN archive.

    EDIT:

    Quote Originally Posted by steveo View Post
    that's good but can you add this cause its not clear what it contains

    "contains most current factory bin files for all vehicle types by part number, and an index spreadsheet to identify them."
    Attached Files Attached Files
    Last edited by RobertISaar; 10-05-2014 at 12:43 PM.
    1995 Chevrolet Monte Carlo LS 3100 + 4T60E


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •