Page 1 of 2 12 LastLast
Results 1 to 15 of 26

Thread: Is it worth it?

  1. #1
    Fuel Injected! BLG355's Avatar
    Join Date
    Feb 2014
    Location
    Elizabethtown, PA
    Age
    41
    Posts
    220

    Is it worth it?

    I am curious, at what point is it worth upgrading beyond the OEM TBI parts, for getting air in and out? Now, I know this can be a loaded question, so if anyone can answer it using my build, I'd appreciate it. Here is what I have going through my head. I originally build my truck to pass PA emissions, which for that year is a visual check, which it does, but I will now be under 5,000 miles per year and qualify for exemption, so I can modify.

    Here the details:
    1995 K1500 with 350, bored .030" over and now at 9.6:1 compression with 72cc dart s/s heads (165 intake). I used the Edelbrock 3704 intake because it retains the EGR Valve I needed. I have heard good and bad about this intake, but for me, at the time, it worked. Will I gain by going with a carb intake and an adapter plate? My cam is pretty much over at 5200 rpm. I also am running stock diameter throttle body have is shaved down. I thought about upgrading to a 454 TB or boring mine to 2" and making new throttle plates, but this would require something other than the 3704 intake. I just want to know if I am wasting time on this or if it would be worth it for up to 5200rpm. I am currently running stock manifolds, but they are going away for long tube ceramic headers this summer...so getting air back out is covered. I see so many different numbers about what the stock 5.7 TB flows, I don't want to be leaving untapped power on the curb. Any feedback is greatly appreciated. Thanks.

    BLG

  2. #2
    LT1 specialist steveo's Avatar
    Join Date
    Aug 2013
    Posts
    4,007
    as far as throttle body size, for power bigger can be better, but throttle response can quickly become non-linear as you go 'too far', you end up a throttle that goes from closed plates to WOT at like 1/2 throttle, which is twitchy, and obviously any calculations that use tps will be out to lunch too

    this is why guys that put bigass throttle bodies on electronic transmissions can have a hell of a time... and tv driven transmissions suffer an equally deadly fate.. since you're pulling WOT air but your tv cable is only partially cracked open... yipe

    in my limited experience with tweaking big engines and too-small throttle bodies, without doing any math, monitoring vacuum under WOT with a fairly accurate meter can tell you if your TB is too restrictive

    if there's restriction at the bores, you'll be pulling some amount of vacuum there when it should be damn near atmospheric (might want to do this test with the air filter off too... dirty air filter will give you lower than atmos. pressure at wot too..)

    now im just learning about TBI, but from what i'm seeing... tbi looks pretty restrictive overall, i mean hell half of the bore is full of injector, so perhaps i'd go for broke...

  3. #3
    Fuel Injected! BLG355's Avatar
    Join Date
    Feb 2014
    Location
    Elizabethtown, PA
    Age
    41
    Posts
    220
    [QUOTE=steveo;40081]
    in my limited experience with tweaking big engines and too-small throttle bodies, without doing any math, monitoring vacuum under WOT with a fairly accurate meter can tell you if your TB is too restrictive

    if there's restriction at the bores, you'll be pulling some amount of vacuum there when it should be damn near atmospheric (might want to do this test with the air filter off too... dirty air filter will give you lower than atmos. pressure at wot too..)
    QUOTE]

    Awesome info right there. I looked at one of my data logs and I can see it in the log, KPA drops into high 80's at MAX RPM and WOT, so I do have room to grow.

    Thanks,

    BLG

  4. #4
    Fuel Injected! Roadknee's Avatar
    Join Date
    Dec 2013
    Location
    North Central Washington
    Age
    54
    Posts
    245
    The stock TB flows under 500 cfm at 1.5" Hg. On a 350 it's pretty well done by 4,500 rpm. A larger TB on the stock style 2 bbl intake will help some, but they are very limited by plenum volume. A good dual plane with an adapter would provide more plenum volume and better top end without much loss in low speed torque. I would even consider either an open spacer or milling the center divider out of the dual plane.

    Years ago I saw a thread where fast355 had some experience running a VicJr 2bbl with a TB and claimed it ran very well. Folks with experience with than manifold claimed it would ice up when the ambient temp dropped below about 40F. I think this is because the VicJr has no heat crossover and the TB injectors don't do a good job of vaporizing fuel. This is probably why the stock intake routes hot water under and around the plenum. Point being if you go to an aftermarket intake, be sure to get one with exhaust crossover passages.

  5. #5

  6. #6
    Fuel Injected!
    Join Date
    Oct 2013
    Posts
    1,022
    Where is your MAP plugged in and what are the specs on your cam?

    When I was playing with TBI on a 350, I cut the ring around the injectors off the top of unit and smoothed the top of the TBI into the bores. I was running a Edebrock Performer intake with an adapter plate. The cam was a 220* duration, about 0.45" lift unit . It never logged anything on the MAP values that would suggest it was pulling a vacuum at higher rpm's.

  7. #7
    Fuel Injected! KidTurbo's Avatar
    Join Date
    May 2014
    Age
    56
    Posts
    27
    Quote Originally Posted by BLG355 View Post
    I thought about upgrading to a 454 TB or boring mine to 2" and making new throttle plates, but this would require something other than the 3704 intake. I just want to know if I am wasting time on this or if it would be worth it for up to 5200rpm.
    I'd find a bigger throttle body for certain. Nothing cuts the power like limiting the air intake. NASCAR used the restrictor plate rule for two decades, because it works. No matter what you do to the rest of the engine, that stock TBI is gonna be your power limiter based on CFM's.

    Not my specialty by any means, but what options are out there in small 4brl throttle bodies these days? My friend runs the largest FASS setup on a big CI Roush motor in his truck, but isn't there some more affordable options out there? I'd try to get in the 650-730 cfm range base on cubic inches alone. And as listed below, a good dual plane intake under it. Then those header will have something to flow..

  8. #8
    Fuel Injected! brian617's Avatar
    Join Date
    Apr 2013
    Location
    Arkansas
    Age
    45
    Posts
    711
    Barry, what kind of air inlet/snorkle/air filter set up you running?
    89 K1500 Scottsdale 5.7L 5spd 3:42 RamJet cam Dart iron TBI heads 427 PCM swap
    95 C2500 Cheyenne 6.5L turbo diesel 4L80e 4:10 DB2-4911 Manual pump conversion 0411 PCM trans control 2Bar COS
    05 Outback XT 2.5L turbo gas auto

  9. #9
    Fuel Injected!
    Join Date
    Feb 2013
    Location
    Euless, TX
    Posts
    2,308
    Quote Originally Posted by Roadknee View Post
    The stock TB flows under 500 cfm at 1.5" Hg. On a 350 it's pretty well done by 4,500 rpm. A larger TB on the stock style 2 bbl intake will help some, but they are very limited by plenum volume. A good dual plane with an adapter would provide more plenum volume and better top end without much loss in low speed torque. I would even consider either an open spacer or milling the center divider out of the dual plane.

    Years ago I saw a thread where fast355 had some experience running a VicJr 2bbl with a TB and claimed it ran very well. Folks with experience with than manifold claimed it would ice up when the ambient temp dropped below about 40F. I think this is because the VicJr has no heat crossover and the TB injectors don't do a good job of vaporizing fuel. This is probably why the stock intake routes hot water under and around the plenum. Point being if you go to an aftermarket intake, be sure to get one with exhaust crossover passages.
    You are describing gasoline (and alcohols) latent heat of vaporization. If you took a pie pan of gasoline and set it in your driveway on a 100*F day, the pie pan would become very cool to the touch.

    I never experienced icing, even in the middle of a snow/ice storm. But that being said, it was in an engine compartment that was very enclosed. I also had such an effective cooling system, that I had over 3/4 of the radiator blocked off by cardboard stuffed in between the radiator and condenser. The MAF picked up air right behind the radiator as well, not many choices for intake configuration on a fullsize G20 Van. I also played with running the system with the stock air cleaner housing and using the factory style hot air heat riser from the header tube. Really didn't make much difference either way in my application. It always took a 10+ minutes for the engine to warm up, idle down, and lean out anyway.

  10. #10
    Fuel Injected! BLG355's Avatar
    Join Date
    Feb 2014
    Location
    Elizabethtown, PA
    Age
    41
    Posts
    220
    Quote Originally Posted by steveo View Post
    80kpa? damn, are you near sea level?

    that's a pretty big restriction
    88kpa. less than 400ft elevation. at lower rpm's and WOT it's mid to high 90's, like 96 or so, and as RPM's increase to shift point at 5300 it's down to 88 or so.

  11. #11
    Fuel Injected! BLG355's Avatar
    Join Date
    Feb 2014
    Location
    Elizabethtown, PA
    Age
    41
    Posts
    220
    Quote Originally Posted by brian617 View Post
    Barry, what kind of air inlet/snorkle/air filter set up you running?
    It is all stock, except i have the Hypertech salad bowl into the air cleaner housing, which i am going to cut the housing back to match the bowl but haven't yet. I also removed the choke in the inlet of the housing, but i am running a stock air filter, no high flow or anything like that yet.

  12. #12
    Fuel Injected! BLG355's Avatar
    Join Date
    Feb 2014
    Location
    Elizabethtown, PA
    Age
    41
    Posts
    220
    Quote Originally Posted by lionelhutz View Post
    Where is your MAP plugged in and what are the specs on your cam?

    When I was playing with TBI on a 350, I cut the ring around the injectors off the top of unit and smoothed the top of the TBI into the bores. I was running a Edebrock Performer intake with an adapter plate. The cam was a 220* duration, about 0.45" lift unit . It never logged anything on the MAP values that would suggest it was pulling a vacuum at higher rpm's.
    The MAP is plugged into the back of the throttle body. I have the top of the throttle body smoothed out pretty good. I am thinking if it isn't in the throttle body itself, it may be in the filter or stock filter housing setup. I'm not 100% sure the cam is actually done at my current shift points, even though its way in the upper end of what that cam can do, but the engine is definitely done, whether it's cam or air flow. I've used similar cams in the past and they pulled harder than this up to 5500, even 5800 rpm, so i think i have some kind of restriction somewhere. Here is cam specs, I have a .480" / .496" lift due to 1.6 roller rockers.

    PART NUMBER: 211252/257 GRIND NUMBER: RR-252/257
    ENGINE INFO: CHEVY SMALL BLOCK V8 305-350 CU.IN. 1988-UP APPLICATION:
    SPECIAL REMARKS: HYDRAULIC ROLLER PRODUCT USE: STREET
    RPM RANGE: 1200-5000
    Valve lift is calculated with zero lash and rocker ratio of 1.5
    INTAKE TIMING
    DURATION:
    252 deg.
    OPEN: 14 BEFORE TDC
    CLOSE: 58 AFTER BDC
    CAM LIFT: .30"
    VALVE LIFT: .450"
    VALVE LASH: . HOT

    . COLD
    EXHAUST TIMING
    DURATION: 257 deg.
    OPEN: 60.5 BEFORE BDC
    CLOSE: 16.5
    AFTER TDC
    CAM LIFT: .310"
    VALVE LIFT: .465"
    VALVE LASH: . HOT

    . COLD

    LOBE CENTER:
    112 deg. OVERLAP: 30.5 deg. CAM ADVANCE: 0 deg.
    THE ABOVE TIMING IS CHECKED AT
    .020
    (OPEN) LIFTER RISE

    .020 (CLOSE)
    The following timing is taken at .050" lifter rise and gives a more accurate determination of camshaft position.
    INTAKE
    DURATION: 204 deg.
    OPEN: -10 BEFORE TDC
    CLOSE: 34 AFTER BDC
    EXHAUST
    DURATION: 209 deg.
    OPEN: 36.5 BEFORE BDC
    CLOSE: -7.5 AFTER TDC
    Last edited by BLG355; 05-30-2014 at 04:21 PM.

  13. #13
    Fuel Injected!
    Join Date
    Oct 2013
    Posts
    1,022
    That's a good low-mid range power cam and your throttle body should work fine with it. I'd try pulling the stock air intake off and then see what the MAP signal does.

  14. #14
    Fuel Injected! brian617's Avatar
    Join Date
    Apr 2013
    Location
    Arkansas
    Age
    45
    Posts
    711
    Quote Originally Posted by BLG355 View Post
    It is all stock, except i have the Hypertech salad bowl into the air cleaner housing, which i am going to cut the housing back to match the bowl but haven't yet. I also removed the choke in the inlet of the housing, but i am running a stock air filter, no high flow or anything like that yet.
    I'm also running the Hypertech bowl but my air cleaner bottom is cut open to match. I'm also running the factory snorkle with divorced heat riser and choke. One other trick I did to mine is use the early 90's flex tube and pull the hour glass center out of the fender mounted baffle. When looking around I noticed the 94-95 set ups are more restrictive. Easy trick to eliminate snorkle and baffle would be just to flip the air cleaner lid and record another WOT.
    89 K1500 Scottsdale 5.7L 5spd 3:42 RamJet cam Dart iron TBI heads 427 PCM swap
    95 C2500 Cheyenne 6.5L turbo diesel 4L80e 4:10 DB2-4911 Manual pump conversion 0411 PCM trans control 2Bar COS
    05 Outback XT 2.5L turbo gas auto

  15. #15
    Fuel Injected! jim_in_dorris's Avatar
    Join Date
    Dec 2011
    Posts
    803
    Nice cam, I would have gone with the RR257/265 grind, but then I am a torque junky.
    Square body stepsides forever!!!

Similar Threads

  1. Is it really worth the extra work to build a 383?
    By jim_in_dorris in forum Gear Heads
    Replies: 27
    Last Post: 11-23-2012, 08:27 AM
  2. Replies: 14
    Last Post: 10-01-2012, 04:53 PM
  3. Hi from Fort Worth
    By 57210 in forum Introductions
    Replies: 3
    Last Post: 05-18-2012, 02:50 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •