Results 1 to 8 of 8

Thread: 94 lt1 tunerpro xdl

  1. #1
    Electronic Ignition!
    Join Date
    Sep 2013
    Posts
    10

    94 lt1 tunerpro xdl

    have XDF file EEX 2.4\EEX xfd | ADX file $EE-16188051-V3.8 adx.
    file has transmission data tables abs,malf codes,trans codes, and more. this is way cool.
    only one problem I only get engine data on tables list.
    hope there is a file here when I post this
    Thanks to steveo and mark
    Last edited by 1badcell; 01-28-2014 at 07:06 AM.

  2. #2
    Electronic Ignition!
    Join Date
    Sep 2013
    Posts
    10
    noob
    Last edited by 1badcell; 01-28-2014 at 07:01 AM.

  3. #3
    Electronic Ignition!
    Join Date
    Sep 2013
    Posts
    10

    94 lt1 tunerpro xdl with attachment

    log file?
    I didn't hit upload button
    I'm tarded.

    trans am 2.2.xdl
    Last edited by 1badcell; 01-28-2014 at 07:00 AM.

  4. #4
    RIP EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    63
    Posts
    10,477
    I moved your other post with attachment to this thread.

    To log other then Engine Data you have to change the ADX file. Go to Acquisition, Edit Definition and choose the Connection and Monitor that you wish to use.

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  5. #5
    Electronic Ignition!
    Join Date
    Sep 2013
    Posts
    10
    ok mark, you are some kind of superhero for all us noobs
    so I see my connection commands. engine,transmission,ABS and clear codes. I have to look at each 1 individually?

    ADX file has tabs in items list , so I only can see engine data now.
    I can just change command to transmission data or ABS, if that's what I want see,
    or change to clear codes(separate engine,trans,ABS)
    can we change commands while logging?

    Thanks for helping all us noobs out!
    Last edited by 1badcell; 01-29-2014 at 01:47 AM.

  6. #6
    RIP EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    63
    Posts
    10,477
    Well you don't have to look at each one individual but that's the way I built it because of complications when changing vehicles. Like F body to B body and most of what people use is engine first then trans second maybe. I just did ABS because someone was curious and so was I to see if I could do it.

    Clear codes while monitoring can be done with out Edit Definition if you have View Toolbars, Data Aquisition Send command showing.

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  7. #7
    Electronic Ignition!
    Join Date
    Sep 2013
    Posts
    10
    have tomorrow off will try it out,
    wanted you to look at file, Looking at it seems like some bad data/missing?
    cable works on all other programs(12pin-usb chip jumper) Log has good connection speed
    car started hard on way home from work just outa the blue boggy till temp hit 160 then ran fine

    need to install permanent laptop datalogger in this car
    Last edited by 1badcell; 01-29-2014 at 03:14 AM.

  8. #8
    RIP EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    63
    Posts
    10,477
    The only thing I see that may need attention is Ignition voltage was only 12.80 ish... should be 14.2 when alternator is charging... along with your start issue it may have weak Batt or alternator?

    Other then that needs the WOT locker patch as your going into PE at 134, so a little VE tuning, but if fuel pump had 14.2 volts it may be why your a little short on fuel up there.

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •