Page 2 of 5 FirstFirst 12345 LastLast
Results 16 to 30 of 74

Thread: Towing with T56

  1. #16
    Fuel Injected!
    Join Date
    Oct 2013
    Posts
    1,022
    Why don't you enlighten everyone and explain how your single experience towing 100 odd miles has proven that a T56 won't prematurely fail if you tow with it without some kind of data showing it was operating safely? For example, temperature data, wear data or oil analysis data that proves nothing wasn't being hurt during the tow.

  2. #17
    Fuel Injected! CDeeZ's Avatar
    Join Date
    May 2012
    Location
    Jokelahoma
    Posts
    422
    I'm sorry. It's not my duty to enlighten you.

    I have towed MANY things with my truck since T56 swapping it. Did I bother to catalogue each instance with a full reportoire of data for you to review? No.

    These are facts:

    My fullsize truck, that wasn't supposed to have a T56 from the factory, now has it.

    Scored a USED T56 on craiglist and installed it.

    FIVE years later, after much daily driving and spirited driving ( I haven't been nice to my T56), and some occasional towing, still going strong with no sign of failure. That's not good enough of course. Not space age technology......




    You're the one with the labratory obviously, why don't we use that for your uber scientific analysis?



    Mrplow did a T56 swap before alot of us:

    http://www.fullsizechevy.com/forum/general-discussion/technical-maintenance/95731-t56-6-speed-swap-2.html
    But that's worthless too, there is no official NASA spec printout with special congressional authorization to verify it so yeah it's no good......

  3. #18
    Fuel Injected!
    Join Date
    Oct 2013
    Posts
    1,022
    And you are still continuing with the insulting bullying tactics. But then attacking the other person is the typical response from someone who can't argue facts...

    Do you have any proof on how quickly the oil was being broken down?
    Do you have any proof that the transmission wasn't overheating?
    Do you have any proof you didn't cause some damage to a bearing or other internal part that will now fail prematurely?
    Do you have any proof you didn't break through the oil film between the 6th gear set and cause a little gear face damage that will propagate into a failure?

    You want to discuss some of the wording in your first post? Your opening claim was that you can tow with a T56. You posted that any internet post that says you can't tow with a T56 was BS. So, since you know these internet posts are myths you must know what is it capable of towing. So can you tow 10,000lbs 100 odd miles but only that much weight and that far? Can you tow 10,000lbs every day for thousands and thousands of miles if you wanted? Can you tow any weight any distance? What about the service interval? Do you change the oil at 1/2 the recommended service interval? At 1/4? At 1/10? What about which gears you should use for the weight you are towing vs the power the engine has? What about ambient temperature? Can it tow 10,000lbs without failing when it's 110*F out or only when it's 70*F out?

    At the end of the day, all you proved was you were able to tow 10,000 lbs 100 odd miles without being broken down on the side of the road due to a transmission failure. Nothing more. Any claim you make beyond that is just as much speculation by you as the internet posts you insulted in your first post.

    As for MrPlow. What gear does he tow in? Using 4th would be WAY easier on the transmission then 6th. Even 5th would be easier on it then 6th. He mentions a pump and oil cooler. So, does he have one or not? That would make a HUGE difference on the towing capacity of the transmission.
    Last edited by lionelhutz; 12-14-2013 at 12:21 PM.

  4. #19
    Fuel Injected! CDeeZ's Avatar
    Join Date
    May 2012
    Location
    Jokelahoma
    Posts
    422
    It's called sarcasm. Maybe you should learn to recognize it. And then maybe not take yourself so seriously?
    Let me restate this yet again
    "
    These are facts:

    My fullsize truck, that wasn't supposed to have a T56 from the factory, now has it.

    Scored a USED T56 on craiglist and installed it.

    FIVE years later, after much daily driving and spirited driving ( I haven't been nice to my T56), and some occasional towing, still going strong with no sign of failure. That's not good enough of course. Not space age technology......

    You're the one with the labratory obviously, why don't we use that for your uber scientific analysis?"

    I think you grossly misinterpreted my post. Some of that might not be your fault beacuse this deal is a lot like text messaging. There is no context when you're not talking face to face.
    Ang again here we go copying and pasting: that is not the only time I have towed with the T56 since swapping it. It was the MOST RECENT instance. So get off the 100 odd miles of towing like it's the only towing this trans has done.
    The reccommended service interval for the T56 staight from GM is to only ever top off the trans if needed, not to ever change the fluid. Myself? I change it every 5,000 - 10,000 miles. Does it need it? Probably not. But I have the peace of mind of knowing that for a few bucks in fluid the trans should live that much longer.
    At the end of the day people like you will always nitpick some little trivial detail and try to blow the whole thing wide open, because you have nothing better to do.
    I have said multiple multiple times: unfortunately the only data I have on this one is real world experience. By itself it's not the be all end all but it does give an indication of what you can realistically do in the real world. It is, one piece of the puzzle figuratively speaking.
    Mr Plow speaks of a pump and cooler. AFAIK, he never used one, just commented to the effect like "hey if you're going to run a T56 in a 6,000 LB bus like my suburban, and you want to do towing regularly of things in the neighborhood of 13,000 LBS; a cooler and a pump would be a good idea". Not sure what gear he towed in, I'm assuming he made use of either of the double ODs.
    Torque multiplication is key
    . If you gear your axle properly to match the deep ratios of the T56 and the tall tires typical of trucks, you can tow anythign WITHIN REASON. Before I had the 4.88s I run now, I had 3.08s from when the truck was an auto, and with the T56 and 3.08s: you had to slip the clutch alot in 1st to get going, and 6th was all but useless, and forget about towing with those 3.08s cuz it's not happening.
    The T56 is not a towrig transmission. Noone has tried to say it should be used in semis and 1 tons and combines. But it is a beefy trans that can hadle alot of what is thrown at it, if you're smart about it.
    I drive at least 200 miles every week for my job, if not even more than that. It was a little over a month ago that I drug this truck back. So IF, something was hurt from towing, I think it would have already reared it's ugly head.

  5. #20
    Fuel Injected!
    Join Date
    Jan 2013
    Posts
    31
    So whats the point of the thread? Are you recomending that people will have no issues towing heavy loads with the t-56? Or is it a thread saying I towed with my T-56? The 4.88 gear might help save the t56. But who wants to tow with 4.88 gears? I could tow 6 times the rated capacity with my old nv1500 as well. At least it has a towing rating. No data to back up any claim you are trying to make, without at least LONG term towing is not really that helpfull. If you are doing it to just mess around an see what it can take then thats cool. But to get your feelings hurt when someone is challenging your finding especially when their statement is that no full size truck came with one for towing is a bit rediculous. All kinds of data would be helpfull from exact combo you are running to the fuel mileage your getting, to a serious longevity test.
    Last edited by S10LS; 12-16-2013 at 06:23 PM.

  6. #21
    Fuel Injected!
    Join Date
    Jan 2013
    Posts
    31
    "Torque multiplication is key". Probably the key to keeping it together. Keep the thread updated so we can see how it does.
    Last edited by S10LS; 12-16-2013 at 06:37 PM.

  7. #22
    Fuel Injected! CDeeZ's Avatar
    Join Date
    May 2012
    Location
    Jokelahoma
    Posts
    422
    The point of the thread was just to show what I did. I'm not reccommending anyone do anything other than use common sense.

    The 4.88s are perfect for a vehicle with a deep gearspread in the trans (T56) and tall tires 29" or above.

    "But who wants to tow with 4.88 gears" Elaboration????

    The fact that the T56 was not given a towing rating is kinda irrelevant I think, a simple quick search on google will turn up plenty of people who have towed with a T56, including Mrplow in his 6,000 lb tank.

    There is data in the form of real world experience. I have towed a pile of axles, motorcycles, engines, etc. This was the most recent and probably the heaviest tow so I chose to report it. When did real world experience become "not-data"?


    Like I said I've been beating on this craigslist T56 for 5 years and have done some occasional towing during that period so I think if towing was going to break this T56 it would have done that in the course of 5 years.


    And as far as the oil analysis data and everything else you guys are talking about. Great idea. Do either of you work at Conoco or something because I don't have access to anything like that.


    Fullsize trucks did come with the T56 , the SRT10. GM toyed with a concept truck that also used the T56 in a stripped down, vinyl floormat fullsize truck. (Never made full production unfortunately).


    The drivetrain combo is a 350 TBI that I screwed together maybe 6 or 7 years ago. ~ 300-350 HP and 400-450 LB/FT est. Elgin cam, ported and polished heads, Ultimate TBI mods, AFPR, TBI and pod spacers, .060 over, HVOP, midlength headers with H pipe and full dual 3" pipes, ported and relieved oil return holes in lifter valley, 7427 PCM swap and DIY tuning. T56 trans obviously. 14 bolt semi floating 9.5" ring gear with 4.88s and Detroit TrueTrac. 3/4 ton brakes all around.
    Last edited by CDeeZ; 12-16-2013 at 10:03 PM.

  8. #23
    RIP EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    63
    Posts
    10,477
    Watching trans oil temps while towing in 4th, 5th and 6th gear would at least say a lot of what the trans is doing with the load and if oil is being heated past it's tolerance.

    Oil analysis can be mailed in by anyone to various companies for engines, not sure who does trans? Diesel shops regularly use analysis at service intervals to see what is wearing in motor.

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  9. #24
    Super Moderator
    Join Date
    Mar 2011
    Location
    Camden, MI
    Age
    35
    Posts
    3,026
    im'ma just do some math here, because i'm curious about this myself:

    T56(no model specified, so i'll assume a 95ish LT1 F-body unit for gearing purposes):


    NV4500(i'll assume another 95 unit, MT8 RPO):


    it's too bad the graph function isn't working at the moment.... it's nice to visualize it as well.

    but those are with the same 4.88 gears(and 28" tire). as far as the highway(55MPH) is concerned, 5th in both is 2350-2400 RPM, but the T56 has the option of 6th gear when possible, RPM would drop to just over 1600.

    to match the same RPM as the T56 6th gear, the NV4500 would need to use 3.35 final gears. i don't know if this is realistic/normal or not.


    anyways, from a purely mathematical perspective..... the T56 gear spacing is VERY nice, has fairly consistent ratio changes, which would certainly help keep the engine in its powerband at any time. the NV4500: not so much. shifting at 3000 will land you anywhere from under 1500 to 2200 in the next gear. some gears, you would need to wind it out a lot further than others to keep the engine from dropping to too low of a speed in the next gear.



    as far as the hardware holding up, i won't speak of it, neither the T56 or the NV4500 is anything i have experience with nor knowledge of. i'm much more interested in seeing how to stuff a T56 into a 4WD S10 chassis with a heavily boosted V6 in front of it for my personal use.
    1995 Chevrolet Monte Carlo LS 3100 + 4T60E


  10. #25
    Fuel Injected! CDeeZ's Avatar
    Join Date
    May 2012
    Location
    Jokelahoma
    Posts
    422
    I would think that any place that analyzes oil should be able to do trans fluid as well, it's still oil after all, just with some hydraulic fluid mixed in as well.
    My T56 is the 95+ model with the 2.66 1st. I believe that is the most common gear spread for T56s, not sure on that one though.
    As that shows, the NV4500 has that short 1st gear which would be very helpful in getting a very heavy load moving, and as you pointed out, 5th is nearly identical.
    "
    anyways, from a purely mathematical perspective..... the T56 gear spacing is VERY nice, has fairly consistent ratio changes, which would certainly help keep the engine in its powerband at any time. the NV4500: not so much. shifting at 3000 will land you anywhere from under 1500 to 2200 in the next gear. some gears, you would need to wind it out a lot further than others to keep the engine from dropping to too low of a speed in the next gear."
    The same closely spaced gears that are enjoyable to just drive/hot rod around in are also helpful when towing because as you stated, it will help keep the engine in the fat spot of the powerband each and every time you shift.
    The NV and T56 are both great gearboxes. Just depends on what you want to do the most. Do you want mainly fun cruising from a brick-shithouse-tough trans that shifts like a sports car and can still do some occasional towing. OR, do you want a true truck trans with that granny 1st gear to really get the load moving. The NV is a wonderful box and certainly has it's place, but it will never have the shift feel and shift throws of a T56 (obviously). Don't anyone misunderstand me, the NV is a great box.
     
    There are/have been/will be some companies offering 4wd T56, not sure if it's available yet? Anyways I have thought much about a 4wd T56 myself, and I know there are people out there who have done it; I believe it usually involves running a divorced T case but check this out
    http://www.google.com/url?sa=i&rct=j&q=&esrc=s&source=images&cd=&cad=rja &docid=9Wt6w2tujfFoNM&tbnid=Lrp-I4q_SnSRUM:&ved=0CAUQjRw&url=http%3A%2F%2Fgrassroo tsmotorsports.com%2Fforum%2Fgrm%2Fcyclonetyphoon-clone-on-a-budget%2F22144%2Fpage1%2F&ei=LWWvUpqZGfTTsAStp4CgD A&bvm=bv.57967247,d.eW0&psig=AFQjCNHrmxo31kDBz7PBX 5FU3MmghzvSBQ&ust=1387311334351554

  11. #26
    LT1 specialist steveo's Avatar
    Join Date
    Aug 2013
    Posts
    4,007
    i can stab my tire with a knife several times without it failing, does that mean

    - it definitely wouldn't fail in short order if i keep doing it?
    - someone else with a different knife might puncture it on the first try?
    - you were perhaps, even subconsiously, stabbing it like a wuss trying to prove your point?

    using the thought process "i've done it a few times and it hasn't broken yet" as a metric for component strength and longevity...... is that good?

    just sayin'

  12. #27

  13. #28
    RIP EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    63
    Posts
    10,477
    Please don't make me delete this thread!

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  14. #29
    Fuel Injected! CDeeZ's Avatar
    Join Date
    May 2012
    Location
    Jokelahoma
    Posts
    422
    4+ years later..... I finally had to take the T56 out to take it apart. But not for any reason related to towing with it, which many internet "experts" say you simply cannot do. The stock stamped steel 3-4 slider keys finally broke, a common problem with T56s that can happen at any time. When this happens it gets stuck in 4th gear. Everything else inside the gearbox looks perfect, bearings, tooth contact patterns, races, synchros etc.

    I bought this used T56 secondhand on CL 8 years ago, beat the shit out if it in this pickup behind a SBC for years. Lately, I have been thrashing it some more behind my S475 turbocharged LQ4 (still in the same heavy AF truck). I also towed with this trans in the truck a few dozen times after the original post, didn't get to run it over a CAT scale every time but it was always around the ballpark of 11,000+ pounds based on the occasions that I did hit a scale.

    Since I'm in the gearbox to replace the broken slider keys I'm bulletproofing it at the same time, building a T56 hybrid. Credit for this info goes to this guy here:
    https://www.eecis.udel.edu/~davis/z2..._Fbody_T56.pdf

    SSR 32 spline mainshaft, solid billet slider keys, bronze fork pads, triple/double cone synchros, TH400 slip yoke. I'm also going to TIG weld a -6AN fitting onto the case for a fluid/sprayer pump. This will eventually get hooked up to a pump which will spray oil directly at the headset gears. Should be a good addition when I start to crank up the boost in this heavy groundpounder.



    The trans on the bench ready for teardown



    Everything inside looks perfect. It's just the goofy stock stamped steel keys that forced me to take it apart.




    The F-body gearset is sticking in the bench. Corvette input in the front cover, F-body laying next to it. Corvette and F-body clutsters laying next to each other.



    SSR oil seal, bronze fork pads, and billet keys. Also a 3/16 loose ball bearing for the upgraded 1/2 snychro retainer.



    SSR mainshaft, VSS reluctor, 1/2 synchro retainer, small input bearing, TH400 yoke, and steel Viper 3/4 fork.



    Not a lick of unusual wear anywhere in the whole thing.



    The C5 Corvette donor trans for the hybrid build.



    Corvette and Fbody T56 torn down. There is a 3rd T56 floating around the shop somewhere haha.
    Last edited by CDeeZ; 02-28-2018 at 02:52 AM.

  15. #30
    Fuel Injected! woody80z28's Avatar
    Join Date
    Nov 2011
    Location
    Walton, NY
    Age
    38
    Posts
    242
    Pretty cool. I've had my FWD 5spd apart a million times but haven't opened up my T56.

    Glad to hear about the towing. The NV4500 in my truck is a beast, but it's good to know I can tow tools and tires if I ever do Drag Week in the Camaro.

    And as far as ratios, the T56 is heaven compared to the NV4500. The splits on the 5spd drive me crazy. Pulling hills with a trailer it always wants to be between 4th and 3rd. And you really do have to wind out the first few gears so the next one doesn't fall on its face. Although the granny low can be nice sometimes. I even put a rocker switch in the front axle actuator so I can have 2LO. Just let the clutch out and it creeps.
    80 Camaro Z28 - 550hp AFR 383 / T56 6spd (Holley HP EFI)
    91 Beretta "SS" - 260hp 3400 MPFI / HM282 5spd (7730/$A1) sold! for crazy money...but I miss it
    94 Silverado Z71 - 300hp Vortec 357 TBI / NV4500 5spd (7427/$0D) gone but not forgotten
    96 Beretta "T56" - 4.8 LS RWD swap / 6spd (0411/2156)
    01 Silverado 2500HD - stock Vortec 8.1 / ZF6 6spd (0411/8322)
    https://www.youtube.com/c/GEARHEADdezign

Similar Threads

  1. Tuning for towing?
    By dyeager535 in forum GM EFI Systems
    Replies: 13
    Last Post: 04-10-2012, 09:18 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •