Page 1 of 3 123 LastLast
Results 1 to 15 of 34

Thread: GM V6 PCM pinouts

  1. #1
    Fuel Injected!
    Join Date
    May 2013
    Posts
    174

    GM V6 PCM pinouts

    I posted this info in my intro thread, but I figured it would be more useful here...

    I've made a pinout sheet for GM obd2 V6 PCMs, I'm working on editing out the typos here and there, so please bare with me. So far, I've used this pinout, along with a L36 5 speed Fbody bin to make my 5 speed 3500 swap work correctly(hopefully...)

    the PCM's these pinouts are derived from support a variety of systems and accessories, including:

    FWD and RWD automatic Transaxles/Transmissions
    Manual Transmissions (3.8 F body)
    DIS (3100, 3400 and, 3800 equipped vehicles)
    Coil per cylinder (3.5 Shortstar)
    DBW throttle (3.8 F body)
    forced induction (3800 supercharged vehicles)
    Dual bank fuel control (3.8 F body)
    dual bank knock sensors (3.8/3800 cars)

    as with all forum info, please use at your own risk.

    the PCM P/N's:

    16236757

    09356741

    09357034

    09361735

    09374997

    09378702

    09380717

    12209614

    12209624


    GM OBD2 V6 PCM pinout chart. USE AT OWN RISK!

    there are 34 totally unused pins

    Blue 2000 grand am 2001 olds aurora Montana 1998 firebird 3.8 2002 firebird 3.8 98-02 L67
    1 Trans temp ground Low Ref Sensor ground - TFT sensor ground
    2 - - - Second gear start indicator Service TCS indicator -
    3 - - - Fuel level indicator - Fuel level indicator
    4 1-2 shift solenoid 1-2 shift solenoid 1-2 shift solenoid 1-2 shift solenoid 1-2 shift solenoid 1-2 shift solenoid
    5 High speed fan High speed fan High speed fan High speed fan High speed fan High speed fan
    6 Low speed fan Low speed fan Low speed fan Low speed fan Low speed fan Low speed fan
    7 Cam position signal Cam position signal Cam position signal Cam position signal Cam position signal Cam position signal
    8 3x crank pos ref high Crank pos 2 signal 3x crank pos ref high 3x crank pos ref 3x crank pos ref 3x crank pos ref
    9 24x crank pos high Crank pos 1 Signal 24x crank pos high 18x crank pos ref 18x crank pos ref 18x crank pos ref
    10 MAP 5v ref MAP 5v ref MAP 5v ref - - MAP 5V ref
    11 - - - - - -
    12 - - - ECT ground Low ref ECT res low
    13 MAP/ECT ground MAP/ECT ground MAP/ECT ground MAP ground Low ref MAP ref low
    14 - - - - UART serial data(secondary -
    15 - - - Serial data UART serial data(Primary) UART serial data
    16 PCM ground PCM ground PCM ground PCM ground PCM ground PCM ground
    17 IAT ground IAT ground IAT ground IAT ground Low reference ECT ground
    18 - - - - - -
    19 IGN + IGN + IGN + IGN + IGN + IGN+
    20 B+ B+ B+ B+ B+ B+
    21 - - - - -
    22 Trans fluid pressure switch A Trans fluid pressure switch A Trans fluid pressure switch A Trans fluid pressure switch A Trans fluid pressure switch A Trans fluid pressure switch A
    23 - - - - - -
    24 - - - - - -
    25 - - - - - -
    26 - - - - -
    27 - - - Bank 1 HO2S 1 low Bank 1 HO2S 1 low -
    28 HO2s 2 Low HO2s 2 Low HO2s 2 Low Bank 1 HO2S 3 low Bank 1 HO2S 3 low HO2S sensor 2 low
    29 HO2s 1 Low HO2s 1 Low HO2s 1 Low Bank2 HO2S 1 low Bank2 HO2S 1 low HO2S sensor 1 low
    30 TCC brake input TCC brake input TCC brake input TCC brake input TCC brake input TCC brake input
    31 EGR pintle position ground EGR pintle position ground EGR pintle position ground Sensor ground Low ref EGR pintle pos ground
    32 EGR valve control EGR valve control EGR valve control EGR valve ground Egr solenoid control EGR IGN+
    33 Knock sensor Knock sensor Knock sensor Bank1 KS Bank1 KS Bank 1 KS
    34 - - - Bank 2 KS Bank 2 KS Bank 2 KS
    35 - - - - -
    36 - - - Generator control - Charge warning light
    37 - - - - -
    38 IAC valve B high IAC valve B high IAC valve B high IAC valve B high - IAC B High
    39 - - - - - Fuel pump speed control
    40 - - - - - -
    41 - - - - - -
    42 - - - - - -
    43 Fuel injector #1 Fuel injector #6 Fuel injector #1 Fuel injector #6 Fuel injector #6 Fuel injector #6
    44 2-3 shift solenoid 2-3 shift solenoid 2-3 shift solenoid Shift solenoid B control 2-3 shift solenoid 2-3 shift solenoid control
    45 AIR valve control AIR valve control AIR valve control - - AIR control solenoid ground
    46 Fuel injector #3 Fuel injector #2 Fuel injector #3 Fuel injector #4 Fuel injector #4 Fuel injector #4
    47 Fuel injector #2 Fuel injector #1 Fuel injector #2 Fuel injector #5 Fuel injector #5 Fuel injector # 5
    48 3x crank position ref Low ICM low ref 3x crank position ref Low 3x crank position ref Low 3x crank position ref Low 3x crank position ref low
    49 - Coil 1 control - - - -
    50 - Coil 2 control - - - -
    51 - Coil 6 control - - - -
    52 - Coil 5 control - - - -
    53 Bypass control Coil 4 control Bypass control Bypass control Bypass control Bypass control
    54 Ignition control Coil 3 control Ignition control Ignition control Ignition control Ignition control
    55 Vehicle speed signal output Vehicle speed signal output Vehicle speed signal output Vehicle speed signal output Vehicle speed signal output Vehicle speed signal output
    56 PCM ground PCM ground PCM ground PCM ground PCM ground PCM ground
    57 PCM ground PCM ground PCM ground PCM ground PCM ground PCM ground
    58 Class II serial Class II serial - - - -
    59 - Class II serial Class II serial Class II serial Class II serial Class II serial
    60 PCM ground PCM ground PCM ground PCM ground PCM ground PCM ground
    61 TPS ground TPS ground TPS ground TPS ground - TPS ground
    62 Input shaft speed low Input shaft speed low Input shaft speed low - - Input shaft speed low
    63 Input shaft speed high Input shaft speed high Input shaft speed high - - Input shaft speed high
    64 VSS high VSS high VSS high VSS high VSS high VSS high
    65 VSS low VSS low VSS low VSS low VSS low VSS low
    66 - - - - -
    67 - - - - -
    68 Transaxle range switch B Transaxle range switch B Transaxle range switch B - - Trans range switch B
    69 MAF signal MAF signal MAF signal MAF signal MAF signal MAF signal
    70 - - - Theft deterrent fuel enable Theft deterrent fuel enable Theft deterrent fuel enable
    71 - Requested torque signal Requested torque - Requested torque Requested torque
    72 Cruise inhibit control Cruise inhibit control Cruise inhibit control Cruise inhibit control - Cruise inhibit control
    73 Fuel injector #5 Fuel injector #4 Fuel injector #5 Fuel injector #2 Fuel injector #2 Fuel injector #2
    74 - - - - -
    75 - - - - Engine hot lamp
    76 Evap purge valve control Evap purge valve control Evap purge valve control Evap purge valve control Evap purge valve control Evap purge valve control
    77 - - - - -
    78 - - - - -
    79 Fuel injector #6 Fuel injector #5 Fuel injector #6 Fuel injector #1 Fuel injector #1 Fuel injector #1
    80 AC pressure sensor ground AC pressure sensor ground AC pressure sensor ref low - - AC pressure sensor ref low






    clear 2000 grand am 2001 olds aurora Montana 1998 firebird 3.8 2002 firebird 3.8 98-02 L67
    1 - - - - - -
    2 EVAP vent solenoid control EVAP vent solenoid control EVAP vent solenoid control EVAP vent solenoid control EVAP vent solenoid control EVAP vent solenoid control
    3 Fuel pump relay control Fuel pump relay control Fuel pump relay control Fuel pump relay control Fuel pump relay control Fuel pump relay control
    4 EGR valve IGN + EGR valve IGN + EGR valve IGN + EGR valve control EGR valve control EGR valve control
    5 SES light SES light SES light SES light SES light SES light
    6 - - Low oil level light Low oil level light - Low oil level light
    7 IAC valve A high IAC valve A high IAC valve A high IAC valve A high - IAC valve A high
    8 - Engine speed signal - - Engine speed signal Tach control
    9 - Delivered torque signal Delivered torque signal - Delivered torque signal Delivered torque signal
    10 HO2s 1 signal HO2s 1 high signal HO2s 1 signal Bank 2 HO2S 1 signal Bank 2 HO2S 1 signal HO2s 1 signal
    11 HO2s 2 signal HO2s 2 high signal HO2s 2 signal Bank 1 HO2S 3 signal Bank 1 HO2S 3 signal HO2s 2 signal
    12 - - Bank 1 HO2S 1 signal Bank 1 HO2S 1 signal -
    13 - - - - -
    14 - - - - -
    15 - - - - -
    16 Transaxle range switch P Transaxle range switch P Transaxle range switch Parity PNP switch Neutral safety switch signal Transaxle range switch P
    17 Trans fluid pressure switch C Trans fluid pressure switch C Trans fluid pressure switch A Transmission range C (4L40E) Transaxle fluid pressure switch C Transaxle fluid pressure switch C
    18 Transaxle range switch A Transaxle range switch A Transaxle range switch A Cruise control/clutch anticipate switch CPP switch signal Transaxle range switch A
    19 Oil pressure input - Oil pressure input - - -
    20 - - - - - -
    21 - - - 2nd gear start signal Traction control switch signal Performance switch input
    22 - - AC request AC request AC request AC request
    23 - Crank voltage crank Crank signal Crank signal -
    24 IGN+ IGN+ IGN+ - Cruise control release signal -
    25 MAP signal MAP signal MAP signal MAP signal MAP signal MAP signal
    26 ECT signal ECT signal ECT signal ECT signal ECT signal ECT signal
    27 AC pressure signal AC pressure signal AC pressure signal AC pressure signal AC pressure signal AC pressure signal
    28 EGR pintle position signal EGR pintle position signal EGR pintle position signal EGR pintle position signal EGR pintle position signal EGR pintle position signal
    29 Generator F terminal monitor Generator field duty cycle signal - - - -
    30 EGR 5v Ref EGR 5v Ref EGR 5v Ref - - EGR 5V ref
    31 - B+ - - - -
    32 FTP 5v ref FTP 5v ref - - - -
    33 TPS 5v ref TPS 5v ref TPS 5v ref TPS 5v ref 5v ref TPS 5v ref
    34 AC pressure 5v ref B AC pressure 5v ref B AC pressure 5v ref B AC pressure 5v ref B 5v ref AC pressure 5v ref B
    35 FTP/fuel level ground FTP/fuel level ground Sensor ground Sensor ground Low ref Sensor ground
    36 - - - - - Change oil lamp control
    37 - HO2s heater low control sensor 1 - - - -
    38 - - - - - -
    39 AC relay control AC relay control AC relay control AC relay control AC relay control AC relay control
    40 - - - - - -
    41 - - - - - -
    42 Fuel injector #4 Fuel injector #3 Fuel injector #4 Fuel injector #3 Fuel injector #3 Fuel injector #3
    43 - - - - - -
    44 IAC valve A low IAC valve A low IAC valve A low IAC valve A low - IAC valve A low
    45 Pressure control solenoid high Pressure control solenoid high Pressure control solenoid high Pressure control solenoid high Pressure control solenoid high Pressure control solenoid high
    46 Pressure control solenoid low Pressure control solenoid low Pressure control solenoid low Pressure control solenoid low Pressure control solenoid low Pressure control solenoid low
    47 - - - - - -
    48 - HO2s low heater control bank 1 sensor 2 - 3-2 control solenoid control 3-2 control solenoid control -
    49 IAC valve B low IAC valve B low IAC valve B low IAC valve B low - IAC valve B low
    50 IAT signal IAT signal IAT signal IAT signal IAT signal IAT signal
    51 - - - - - -
    52 - - - - - -
    53 - Oil pressure signal - - - -
    54 - - - - - -
    55 FTP signal FTP signal FTP signal FTP signal FTP signal FTP signal
    56 Transaxle range switch C Transaxle range switch C Transaxle range switch C - - Transaxle range switch C
    57 Trans fluid pressure switch B Trans fluid pressure switch B Trans fluid pressure switch B Transmission range B (4L60E) Trans fluid pressure switch B Trans fluid pressure switch B
    58 Oil level switch input Oil level switch input Oil level switch input Oil level switch input Oil level switch input Oil level switch input
    59 Cruise status Cruise status Cruise status Cruise status - Cruise status
    60 - Extended travel brake switch signal - - - -
    61 Generator L terminal control Generator on signal Generator control - Generator turn on signal Generator L terminal control
    62 - - - - - -
    63 TCC brake input TCC brake input TCC brake input - - TCC brake input
    64 - - - - - -
    65 - - - - - -
    66 TPS signal TPS signal TPS signal TPS signal - TPS signal
    67 - - - - - -
    68 Trans fluid temp signal Trans fluid temp signal Trans fluid temp signal Trans fluid temp signal Trans fluid temp signal Trans fluid temp signal
    69 Fuel level input Fuel level input Fuel level input Fuel level input Fuel level input Fuel level input
    70 24x crank pos B+ 12 volt ref Crank/Cam pos ground - - -
    71 - 12 volt ref - - - -
    72 Cam pos B+ 12 volt ref Crank/Cam pos B+ - - -
    73 Cam pos ground Low reference Crank/Cam pos ground - - -
    74 24x crank pos ground Low reference Crank/Cam pos B+ - - -
    75 AIR relay control AIR relay control AIR relay control - - AIR relay control
    76 - Starter relay coil control Starter relay coil control Starter relay coil control Starter relay coil control -
    77 - - - - Boost control solenoid control circuit
    78 TCC PWM solenoid control TCC PWM solenoid control TCC PWM solenoid control TCC PWM solenoid control TCC PWM solenoid control TCC PWM solenoid control
    79 - - - TCC enable solenoid control TCC enable solenoid control -
    80 - Low ref - - -

    GM 12200411 PCM pinouts S10 Vs typical V8. Use at own risk.



    blue 2002 S-10 4.3 Typical V8 0411
    1 ground ground
    2 12v ref 12V reference
    3 - Fuel injector #3
    4 Fuel injector #4 Fuel injector #2
    5 - -
    6 - -
    7 - -
    8 5v ref -
    9 Knock sensor signal -
    10 - -
    11 - KS #2 signal
    12 Crank pos signal Crank position signal
    13 - Requested torque signal
    14 - UART serial data secondary
    15 - UART serial data tertiary
    16 - -
    17 Trans fluid pressure switch signal B Trans fluid pressure switch signal B
    18 Trans fluid pressure switch signal C Trans fluid pressure switch signal C
    19 IGN+ IGN+
    20 B+ B+
    21 Low ref Low ref
    22 - -
    23 Low ref Low ref
    24 - -
    25 HO2S low bank2 sensor 1 HO2S low bank2 sensor 1
    26 HO2S low bank2 sensor 2 HO2S low bank2 sensor 2
    27 - -
    28 HO2S low signal bank 1 sensor 2 HO2S low signal bank 1 sensor 2
    29 HO2S low signal bank 1 sensor 1 HO2S low signal bank 1 sensor 1
    30 Coolant level switch signal Coolant level switch signal
    31 - -
    32 Transmission range signal A Transmission range signal A
    33 TCC brake switch signal TCC brake switch signal
    34 Transmission range switch signal P Transmission range switch signal P
    35 CPP switch signal CPP switch signal
    36 Fuel injector #1 Fuel injector #1
    37 Fuel injector #3 Fuel injector #6
    38 - Damping lift/dive signal
    39 - -
    40 ground ground
    41 - Low ref
    42 - -
    43 Fuel injector #5 Fuel injector #7
    44 - Fuel injector #5
    45 - FTP 5V ref
    46 5v ref TPS 5V ref
    47 - MAP 5V ref
    48 5v ref EGR 5V ref
    49 Low ref -
    50 - -
    51 - KS bank 1 signal
    52 - -
    53 Low ref (RPO M30 only) Low reference
    54 Low ref Low reference
    55 - EGR valve position signal
    56 - -
    57 B+ B+
    58 Class II serial Class II serial
    59 Class II serial Class II serial
    60 Low ref Low ref
    61 Low ref Low ref
    62 - -
    63 HO2S low ref Low ref
    64 - -
    65 - HO2S high signal bank 2 sensor 2
    66 HO2S High signal HO2S high signal bank 2 sensor 1
    67 - -
    68 HO2S high signal HO2S high signal bank 1 sensor 2
    69 HO2S high signal HO2S high signal bank 1 sensor 1
    70 - Oil level switch
    71 - -
    72 Trans range switch signal B Trans range switch signal B
    73 Cam position signal Cam position signal
    74 ECT signal ECT signal
    75 B+(RPO M30 only) B+
    76 Fuel injector #3 Fuel injector #5
    77 Fuel injector #6 Fuel injector #8
    78 - -
    79 3-2 shift solenoid control 3-2 shift solenoid control
    80 Low ref Low ref




    Red 2002 S-10 4.3 Typical V8 0411
    1 Ground Ground
    2 TCC PWM solenoid control TCC PWM solenoid control
    3 - Secondary fuel pump relay control
    4 - -
    5 - Delivered torque signal
    6 PC solenoid high control (A) PC solenoid high control (A)
    7 - EGR supply voltage
    8 PC solenoid low control(A) PC solenoid low control(A)
    9 Primary fuel pump relay control Primary fuel pump relay control
    10 Engine speed signal Engine speed signal
    11 - AC high pressure recirc switch signal
    12 - -
    13 Cruise status Cruise status
    14 - -
    15 Generator turn on signal Charge indicator control
    16 4wd low signal 4wd low signal
    17 AC request AC request
    18 - -
    19 Axle switch signal Axle switch signal
    20 VSS low VSS low
    21 VSS high VSS high
    22 - ISS high
    23 - ISS low
    24 TPS signal -
    25 IAT signal IAT signal
    26 IC timing signal Coil 1 control
    27 - Coil 7 control
    28 -- Coil 6 control
    29 - Coil 4 control
    30 - -
    31 MAF signal MAF signal
    32 MAP signal MAP signal
    33 - Recirc actuator control
    34 EVAP purge control EVAP purge control
    35 - -
    36 - AIR pump relay
    37 - -
    38 - -
    39 12V ref 12V ref
    40 ground ground
    41 - EGR solenoid control
    42 TCC solenoid control TCC solenoid control
    43 AC relay control AC relay control
    44 - -
    45 EVAP vent control EVAP vent control
    46 SES light SES light
    47 2-3 shift solenoid 2-3 shift solenoid
    48 1-2 shift solenoid 1-2 shift solenoid
    49 Vehicle speed signal Vehicle speed signal
    50 VSS signal VSS signal
    51 Trans fluid temp signal Trans fluid temp signal
    52 Generator field duty cycle signal Generator field duty cycle signal
    53 - -
    54 Low ref Fuel level signal(primary)
    55 AC low pressure switch signal AC low pressure switch signal
    56 - -
    57 Low ref Low ref
    58 - -
    59 - -
    60 - Low ref
    61 - Low ref
    62 Trans range switch signal C Trans range switch signal C
    63 Trans pressure switch signal A Trans pressure switch signal A
    64 STP pressure signal STP pressure signal
    65 - -
    66 - Coil 8 control
    67 - Coil 2 control
    68 - Coil 5 control
    69 - Coil 3 control
    70 - -
    71 - -
    72 HO2S heater low control bank 2 sensor 1 HO2S heater low control bank 2 sensor 1
    73 - Fuel level signal (secondary)
    74 HO2S heater high control bank 2 sensor 1 HO2S heater high control bank 2 sensor 1
    75 - -
    76 IAC coil B high control IAC coil B high control
    77 IAC coil B low control IAC coil B low control
    78 IAC coil A low control IAC coil A low control
    79 IAC coil A high control IAC coil A high control
    80 HO2S heater low ref Low ref

    2008 Trailblazer 4.2 I6

    PIN FUNCTION COLOR NOTES
    1 CRANK VOLT PPL TO STARTING/CHARGING SYS
    2 TCC BRAKE SW PPL ANTI LOCK BRAKE SYS
    3
    4 4WD LO SIG GRY/BLK TRANSMISSION SYSTEMS
    5
    6
    7 CHMSL CTRL LT BLU CRUISE CONTROL SYSTEMS
    8
    9 LO REF BLK FUEL TANK PRESSURE/FUEL PUMP AND SENDER ASSEMBLY
    10
    11
    12 MIL CTRL BRN/WHT TO INSTRUMENT CLUSTER MIL
    13 FUEL PMP RLY CRTL DKGRN/WHT
    14
    15
    16 CLASS 2 SER DATA DKGRN COMPUTER DATA LINES SYS
    17
    18 IGN VOLT PNK IGN D FUSE (REAR FUSE BLOCK)
    19 IGN VOLT PNK ECM 1 FUSE (UNDERHOOD FUSE CENTER)
    20 BATT POS VOLT ORG ECM FUSE (UNDERHOOD FUSE CENTER
    21 ACCEL SW SIG GRY/BLK CRUISE CONTROL SYSTEM
    22 CRUISE CTRL SET DK BLU CRUISE CONTROL SYSTEM
    23
    24
    25 ENG SPD SIG WHT INSTRUMENT CLUSTER
    26
    27
    28
    29
    30 CRUISE ON SW SIG GRY CRUISE CONTROL SYSTEM
    31
    32
    33 5V REF WHT/BLK ACCELERATOR POSITION SENSOR
    34 5V REF GRY FUEL TANK PRESSURE SENSOR
    35 5V REF GRY ACCELERATOR POSITION SENSOR
    36 LO REF BRN ACCELERATOR POSITION SENSOR
    37 LO REF PPL ACCELERATOR POSITION SENSOR
    38
    39 VEHICLE SPD SIG DK GRN/WHT INSTRUMENT CLUSTER
    40 PWETRAIN RLY CTRL YEL POWERTRAIN RELAY
    41
    42
    43
    44 FUEL LVL SENS SIG PPL FUEL TANK PRESSURE/FUEL PUMP AND SENDER ASSEMBLY
    45
    46
    47 APP SENS 1 SIG DK BLU ACCELERATOR POSITION SENSOR
    48 FUEL TANK SENS DKGRN FUEL TANK PRESSURE SENSOR
    49 APP SENS 2 SIG ACCELERATOR POSITION SENSOR
    50
    51 AIR INJECTION CTRL PNK/BLK AIR SOL RELAY
    52
    53 A/C CLUTCH RLY DK GRN/WHT AIR CONDITIONING SYSTEM
    54
    55 EVAP SOL CTRL WHT EVAP CANISTER VENT
    56 STARTER RLY CTRL YEL/BLK STARTING/CHARGING SYS



    PIN FUNCTION COLOR NOTES
    1 IC 1 CTRL PPL IGN COIL 1 PIN B
    2 HO2S LO SIG TAN PIN A HO2S 1
    3 HO2S HI SIG PPL/WHT PIN B HO2S 2
    4 HO2S HI SIG PPL/WHT PIN B HO2S 1
    5 HO2S LO SIG TAN/WHT PIN A HO2S 2
    6 KS 2 SIG LT BLU PIN A KNOCK SENSOR 2
    7 KS 2 SIG GRY PIN B KNOCK SENSOR 2
    8 KS 1 SIG DK BLU PIN A KNOCK SENSOR 1
    9 KS 1 SIG GRY PIN B KNOCK SENSOR 1
    10
    11 TAC MOTOR CTRL 1 YEL THROTTLE BODY PIN B
    12 TAC MOTOR CTRL 2 BRN THROTTLE BODY PIN A
    13 IGN VOLT PNK
    14 CAMSHAFT JI CTRL BRN PIN A CAMSHAFT ACTUATOR SOLENIOD ASSEMBLY
    15
    16
    17 IC 5 CTRL DK GRN IGN COIL 5 PIN B
    18
    19
    20
    21
    22
    23 LO REF PNK/BLK CAMSHAFT POSITION SENSOR PIN B
    24 LO OIL PRES SW SIG PPL OIL PRESSURE SWITCH PIN B
    25
    26
    27 LO REF BLK CRANKSHAFT POSITION SENSOR PIN B
    28
    29 LO REF BLK/WHT THROTTLE BODY PIN C
    30
    31
    32 FUEL INJ 6 CTRL YEL/BLK
    33 IC 3 CTRL LT BLU IGN COIL 3 PIN B
    34 IC 4 CTRL DK GRN/WHT IGN COIL 4 PIN B
    35
    36
    37
    38
    39 12V REF RED CAMSHAFT POSITION SENSOR PIN A
    40
    41
    42 LO REF BLK MAF SENSOR PIN D
    43 STARTER RLY CTRL DK BLU
    44 5V REF GRY THROTTLE BODY PIN E
    45
    46 LO REF BLK PIN B CAMSHAFT ACTUATOR SOLENIOD ASSEMBLY
    47
    48 FUEL INJ 6 CTRL BLK/WHT
    49 FUEL INJ 4 CTRL LT BLU/BLK
    50
    51
    52 FUEL INJ 2 CTRL LT GRN/BLK
    53 IC 6 CTRL LT BLU/WHT IGN COIL 6 PIN B
    54 IC 2 CTRL RED/WHT IGN COIL 2 PIN B
    55
    56
    57
    58
    59 CMP SENS SIG BLK PIN C CAMSHAFT POSITION SENSOR
    6O
    61
    62 IAT SENS SIG TAN MAF SENSOR PIN E
    63 CKP SENS SIG BRN/WHT PIN C CRANKSHAFT POSITION SENSOR
    64 TP SENS 1 SIG DK GRN THROTTLE BODY PIN D
    65
    66 TP SENS 2 SIG PPL THROTTLE BODY PIN F
    67 MAF SENS SIG YEL MAF SENSOR PIN A
    68 HO2S HTR LO CTRL DK GRN PIN E HO2S 1
    69 HO2S HTR LO CTRL BLK/WHT PIN E HO2S 2
    70
    71 FUEL INJ 3 CTRL PNK/BLK
    72 FUEL INJ 1 CRTL BLK
    73 GND BLK




    PIN FUNCTION COLOR
    1
    2
    3
    4
    5
    6
    7 GEN REGU CTRL PPL STARTING/CHARGING SYS
    8
    9 AIR PUMP RLY CTRL BRN SECONDARY A.I.R. PUMP RELAY
    10
    11
    12 DELIVERED TORQ SIG TAN/BLK
    13
    14
    15
    16
    17 REQUEST TORQ SIG ORG/BLK
    18
    19
    20
    21 LO REF BRN A/C SYS
    22
    23 LO REF ORG/BLK MAP SENSOR PIN 2
    24
    25
    26 AIR INJECTION CTRL DK BLU/WHT SECONDARY A.I.R. PUMP RELAY PIN 1
    27
    28
    29
    30
    31
    32
    33 HISPD DATA BUS- TAN
    34
    35 LO REF BLK ECT SENSOR PIN A
    36
    37 5V REF GRY A/C SYS
    38
    39 5V REF GRY MAP SENSOR PIN 1
    40
    41
    42 AIR INJECTION CTRL BRN/WHT SECONDARY A.I.R. PUMP RELAY PIN 3
    43
    44
    45
    46
    47 PNP SW SIG ORG/BLK STARTING/CHARGING SYS
    48 EVAP CANISTER CTRL DK GRN/WHT PIN B EVAP CANISTER PURGE SOLENIOD
    49
    50
    51
    52
    53 HI SPD DATA BUS+
    54
    55 ECT SENS SIG YEL ECT SENSOR PIN B
    56
    57 A/C PRESS SENS RED/BLK A/C SYS
    58
    59 MAP SENS SIG LT GRN MAP SENSOR PIN3
    6O
    61
    62 SEC AIR INJ SENS YEL SECONDARY A.I.R. PUMP RELAY PIN 2
    63
    64
    65 OIL PRESS SW SIG TAN/BLK ENGINE OIL PRESSURE SWITCH PIN A
    66 FRONT SIG HIGH TRANSMISSIONS SYS
    67
    68
    69
    70
    71
    72
    73
    Attached Files Attached Files
    Last edited by ericjon262; 02-06-2015 at 10:09 AM.

  2. #2
    RIP EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    63
    Posts
    10,477
    Well thanks for very useful first posts!

    What years or makes models on these pin outs and I will add to or start a thread for them?

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  3. #3
    Fuel Injected!
    Join Date
    May 2013
    Posts
    174
    Quote Originally Posted by EagleMark View Post
    Well thanks for very useful first posts!
    Your Welcome!


    Quote Originally Posted by EagleMark View Post
    What years or makes models on these pin outs and I will add to or start a thread for them?
    if you find anything else on it, feel free to post it here and I'll add it to it! when I get back in town I'll upload the PDF version too, along with a couple of other bins I have if they aren't already here.

    most of the info is from 1998-2002 V6 cars and minivans, including:

    1998 L36 F body
    2000 LA1 Grand Am
    1998 L67 Grand Prix
    1999 U body Van
    2000 U body Van

    I believe one pinout I have looked at has a typo, but I've been unable to verify 100% yet, and that is pin 58 on the blue connector.

    I have been finding new pins mostly by accident lately, I needed a new pigtail for my PCM and the pigtail I yanked out of a van had pins my car pigtail didn't....

    most of them were from comparing pinouts from cars with different parameters though.

    Example:

    L67 PCM will need pins for the Boost control circuit, where a LA1 wouldn't. RWD L36 PCM will have 3 o2 sensors, where a FWD L36/L67/LA1 would only have 2. this is also how I stumbled across the second knock sensor, and the clutch anticipate input. IIRC, this PCM also has capabilities to run a DBW TB, as the later L36 F bodies use DBW instead of a cable throttle, but I still need to verify that they use the same PCM first. To be honest though, ATM, it's very low on the list as I don't really care for DBW. the only thing that interests me about it is the additional inputs and outputs available.

    I've also found some interesting software anomalies that I have yet to be able to explain as easily, like how this PCM has only been used behind V6's, yet has codes for cylinder 7 and 8 misfire available to be turned on in the programming.... are there injector drivers for two more cylinders in there somewhere?

    tidbits like that make me wonder how hard it would be to get real coil per cylinder (Vs. DIS) on the V6 engines.

    I'm pretty excited about getting started on hacking these systems, but I am a total newb, I have a ton of learning to do before I'm ready to start digging too deep into it. hardware is easy, but getting it to work... lol!

  4. #4
    Fuel Injected!
    Join Date
    May 2013
    Posts
    174
    I found another application using one of the above mentioned part numbers, this time, it's the 3.5L "shortstar" engine that was most common in olds auroras. specific model years, 2001-2002. I also think I may have found where to get coil per cylinder ignition now...

    this could get interesting. anyone have a bin file laying around for a 2001-2002 olds aurora with a 3.5?

    Edit:

    so far, my info show the LX5 uses a single 24x crank position sensor instead of the dual arrangement the 60V6 uses, and uses a cam sensor setup much like the 3800.

    does anyone know if the cam position signal is the same between the 3800 and the 60V6?


    this could get interesting quick...
    Last edited by ericjon262; 05-10-2013 at 10:39 AM.

  5. #5
    Super Moderator
    Join Date
    Mar 2011
    Location
    Camden, MI
    Age
    35
    Posts
    3,026
    keep in mind the Intrigues had the same engine starting in 99.

    short version: PCM supplies individual signals for 6 coils, which are fed to two different ICMs.

    1 cam sensor, 3 wire(so likely hall-effect) and 1 crank sensor, dual pattern, 6 wire(so likely hall effect). both of which are fed directly to the PCM. system can run with 1 crank signal, but both are preferred. losing cam signal would likely either stop the system from functioning or revert the ICMs into waste-spark.
    1995 Chevrolet Monte Carlo LS 3100 + 4T60E


  6. #6
    Fuel Injected!
    Join Date
    May 2013
    Posts
    174
    a little update, what I thought was a typo with the grand am pinout probably isn't, as it has popped up again in the short* pinout, interesting tidbit though, the short* uses two class II serial outputs not one like most of the 60V6 or 90V6 pinouts I'd looked at... there are other differences, and I'll update the list later tonight when I have more time to work on it.

    I'm going to try to yank a PCM tomorrow at the JY from a short* so that maybe I can get a bin file to look at. I'd be very interested to see if any of the software I have will recognize it, and what parameters are available to tune.

  7. #7
    Super Moderator
    Join Date
    Mar 2011
    Location
    Camden, MI
    Age
    35
    Posts
    3,026
    according to the database in tinytuner, it MIGHT.
    1995 Chevrolet Monte Carlo LS 3100 + 4T60E


  8. #8
    Fuel Injected!
    Join Date
    May 2013
    Posts
    174
    Quote Originally Posted by RobertISaar View Post
    according to the database in tinytuner, it MIGHT.
    that would be awesome!

    anyone have instructions on how to make a bench to flash/ read a PCM on?

    doesn't seem like it would be that hard, 12V power supply, a DLC, and a switch. I have an old computer PS, and IIRC, they are 12V right?

  9. #9
    RIP EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    63
    Posts
    10,477
    I just looked up that PCM and it looks just like the 0411 which the Roadrunner is...

    http://www.hptuners.com/forum/showth...-Bench-Harness

    and the benchtop I made...
    http://www.gearhead-efi.com/Fuel-Inj...amming-harness
    Attached Images Attached Images

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  10. #10
    Fuel Injected!
    Join Date
    May 2013
    Posts
    174
    Quote Originally Posted by EagleMark View Post
    I just looked up that PCM and it looks just like the 0411 which the Roadrunner is...

    http://www.hptuners.com/forum/showth...-Bench-Harness

    and the benchtop I made...
    http://www.gearhead-efi.com/Fuel-Inj...amming-harness
    thats all I thought there was to it, thanks!

    as for the RR 0411Vs V6, they are the same case, but the chips are not in the same place on the inside.

  11. #11
    Fuel Injected!
    Join Date
    May 2013
    Posts
    174
    for your viewing pleasure, it's now a table, showing a couple of the main pinouts I've used to create this.

  12. #12
    Fuel Injected!
    Join Date
    May 2013
    Posts
    174
    still working on it, added the "0411" for shits and giggles, and also added in the L67 pinout. next will be the 99-02 firebird, it should be a little different, as it uses DBW. we'll see.

  13. #13
    Fuel Injected!
    Join Date
    May 2013
    Posts
    174
    ok, worked out a couple of typo's in the original chart, and added the 2002 firebird pinout. I also removed the 0411 from the original and created a second chart specifically for it. Next project will be to trace out all of the generic pin listings to get better definition.

  14. #14
    RIP EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    63
    Posts
    10,477
    It's not easy to format like that in the forums, nice work!

    You know you can upload spreadsheets here if that is easier for you to work with...

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  15. #15
    Fuel Injected!
    Join Date
    May 2013
    Posts
    174
    Quote Originally Posted by EagleMark View Post
    It's not easy to format like that in the forums, nice work!

    You know you can upload spreadsheets here if that is easier for you to work with...
    funny you would say that, I made a table in open office, then just did the old copy and paste. it works here, but not on any of the other forums I'm on.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •