Results 1 to 3 of 3

Thread: Head Temperature Old School!

  1. #1
    RIP EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    63
    Posts
    10,477

    Head Temperature Old School!

    Just thought of something I used a long time ago on my Harley. It was a Ultra Classic with a side car, geared for sidecar, carbed, cammed and piped and would run 70-80 with ease. Had an oil cooler, switched to synthetic oil and tyranny fluid do to Yuma AZ heat.

    The Harley dealer was into building his own planes. Was on his second. Jim was his name, just a cool old gear head that had a small Harley shop on the border of Mexico. Full machine shop too.

    So he says why don't we watch the head temperatures? I say? He says theres head temperature gauges in the air plane magazines that are just run under spark plug. So he gets me one gauge with two sweeping handles! So we had both cylinders on one gauge.

    Now I know this was air cooled stuff but could these gauges lead to optimum cylinder temperatures? Isn't a key goal on timing watching Exhaust Gas Temperatures? Could they be correlated?

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  2. #2
    Super Moderator
    Join Date
    Mar 2011
    Location
    Camden, MI
    Age
    35
    Posts
    3,026

    Re: Head Temperature Old School!

    i don't know about optimum head temps, but it would give you a good idea of if you're running too close to the limit of your head's casted material. i think aluminum starts melting around 900*F?

    i'm fairly certain EGTs and head temps will rise and fall in similar situations, just the rate at which they do so may be different.
    1995 Chevrolet Monte Carlo LS 3100 + 4T60E


  3. #3
    Fuel Injected! gregs78cam's Avatar
    Join Date
    May 2011
    Location
    N. Idaho
    Posts
    767

    Re: Head Temperature Old School!

    6061 melts around 1100 degrees. HOWEVER, being a welder, I can tell you that a large thick chunk of aluminum will take quite a few seconds to form a puddle even with a 200 amp Tig torch pushing a 3000+ degree arc into it. So even a 1/4" thick combustion chamber with water running on the other side will transfer a LOT of heat out, without melting.
    1978 Camaro Type LT, 383, Dual TBI, '7427, 4L80E
    1981 Camaro Z-28 Clone, T-Tops, 350/TH350
    1981 Camaro Berlinetta, V-6, 3spd
    1974 Chevy/GMC Truck, '90 TBI 350, '7427, TH350, NP203, 6" lift, 35s

Similar Threads

  1. Uphill to school both ways
    By 1project2many in forum GM EFI Systems
    Replies: 19
    Last Post: 02-27-2012, 06:00 AM
  2. 4.0L HO Head and 2004 Tuned Port MPFI Intake DIS Distributor
    By EagleMark in forum Buy - Sell - Trade - Wanted
    Replies: 0
    Last Post: 09-09-2011, 11:20 PM
  3. Coolant Temperature Sensor Diagnostic Test CTS
    By EagleMark in forum GM EFI Systems
    Replies: 0
    Last Post: 03-28-2011, 04:33 AM
  4. Replies: 0
    Last Post: 02-19-2011, 04:54 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •