Results 1 to 4 of 4

Thread: Fuel Pump Relay Wiring

  1. #1
    RIP EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    63
    Posts
    10,477

    Fuel Pump Relay Wiring

    The practice of wiring the fuel pump through an external relay has two objectives:

    1.To protect the computer from over-current damage. (Some circuit traces inside may burn open if a pump or other component has problems. This is an expensive failure to repair).
    2.To minimize voltage drop to the fuel pump. (Small gauge wire, switches and/or long runs to the pump may cause a drop in the power needed to run at full output).
    Use a Bosch relay 0-332-204-150, or a standard 12V/30 amp. automotive style single pole, double throw with the terminals marked 30, 85, 86, 87, 87a.

    1.Mount the relay in a suitable place on the firewall. A socket for the relay is okay, or just use push-on terminals.
    2.Use the red fuel pump wire from the computer to activate the relay through pin 86. Ground pin 85 to the chassis.
    3.Find a +12V source capable of supplying at least 15 amps, such as a terminal block on the firewall, or even directly to the battery. Install an in-line fuse of 10-15 amps and attach to pin 30 of the relay using 12-10 gage wire.
    4.Attach a 12-10 gauge wire from pin 87 (the normally open contact) to the (+) terminal of the pump. Ground the pump (-) terminal to the chassis using 12-10 gage wire.
    The computer will turn the pump on and off as before, and allow it to run at full power.

    [attachment=0:id245ru2]fuelpump_relay_wiring.gif[/attachment:id245ru2]
    Attached Images Attached Images

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  2. #2
    Super Moderator
    Join Date
    Mar 2011
    Location
    Camden, MI
    Age
    35
    Posts
    3,026

    Re: Fuel Pump Relay Wiring



    on the V6 cars, there's actually a dedundant circuit that uses an oil pressure switch that will power the fuel pump whenever oil pressure is above 4PSI and the relay itself fails.
    1995 Chevrolet Monte Carlo LS 3100 + 4T60E


  3. #3
    RIP EagleMark's Avatar
    Join Date
    Feb 2011
    Location
    North Idaho
    Age
    63
    Posts
    10,477

    Re: Fuel Pump Relay Wiring

    Pretty sure that's how TBI engines are too. From factory. But this is what most people do with a conversion system. Deleting the oil pressure switch.

    1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
    1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
    -= =-

  4. #4
    Super Moderator dave w's Avatar
    Join Date
    Feb 2011
    Posts
    6,264

    Re: Fuel Pump Relay Wiring

    Quote Originally Posted by RobertISaar


    on the V6 cars, there's actually a dedundant circuit that uses an oil pressure switch that will power the fuel pump whenever oil pressure is above 4PSI and the relay itself fails.
    The redundant oil pressure switch is also used on V6 / V8 cars and pickups.

    dave w

Similar Threads

  1. Replies: 80
    Last Post: 09-25-2022, 08:24 PM
  2. Programable Fuel Pump Voltage Pressure
    By EagleMark in forum GM EFI Systems
    Replies: 1
    Last Post: 08-01-2011, 06:04 AM
  3. gm tbi with a Ford fuel pump?
    By rsgt in forum GM EFI Systems
    Replies: 7
    Last Post: 06-06-2011, 07:25 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •