Page 2 of 3 FirstFirst 123 LastLast
Results 16 to 30 of 31

Thread: 2005 TunerPro Bin Files

  1. #16
    Electronic Ignition!
    Join Date
    Dec 2015
    Age
    60
    Posts
    15
    Hi all;

    Didn't the SS use the LQ9 6.0L?

    Mike

  2. #17
    Carb and Points!
    Join Date
    Aug 2019
    Age
    46
    Posts
    7
    6.0l

  3. #18
    Fuel Injected!
    Join Date
    Nov 2017
    Location
    Californiacation
    Age
    57
    Posts
    811
    This one on first page: 05 Chevy 1500 4x4 MPV L59 12592618.bin (1.00 MB) says it's 4x4 but I just checked my buds 2004 SS 6.0L file and it has 4wd option enable too. It's a starting point :)
    -Carl

  4. #19
    Carb and Points!
    Join Date
    Aug 2019
    Age
    46
    Posts
    7
    The L59 is a 5.3L right not the 6.0l I was looking for

  5. #20
    Fuel Injected!
    Join Date
    Nov 2017
    Location
    Californiacation
    Age
    57
    Posts
    811
    Yep, you are correct, had to look it up. What about this one? 05 Chevy 1500 4X4 6.0L 12592618.bin (1.00 MB)
    -Carl

  6. #21
    Carb and Points!
    Join Date
    Mar 2021
    Age
    42
    Posts
    5
    need a little help, and of course it on my personal vehicle, a 2005 yukon xl SLT with air suspension "auto ride"
    the OS that came on the truck (not sure if the original OS, but the air works with it) is
    OS 12606961

    the reason i need to switch is that another person had a LQ4 in the truck that is no longer in the truck, so to put it back to a LM7 i am currently running a 2618 OS from a silverado.

    the question is, does anyone know how to enable the air suspension in the 2618 OS or have a clean copy of the 12606961 OS?

    thanks
    JCC

    edit -found out 9691 is the update OS for 2618, so ive grabbed an escalade os copy to attemp to get the autoride running
    Last edited by JCCARTER; 05-31-2022 at 06:06 AM.

  7. #22
    Fuel Injected! Pulse_GTO's Avatar
    Join Date
    Aug 2020
    Age
    45
    Posts
    174
    Quote Originally Posted by JCCARTER View Post
    need a little help, and of course it on my personal vehicle, a 2005 yukon xl SLT with air suspension "auto ride"
    the OS that came on the truck (not sure if the original OS, but the air works with it) is
    OS 12606961

    the reason i need to switch is that another person had a LQ4 in the truck that is no longer in the truck, so to put it back to a LM7 i am currently running a 2618 OS from a silverado.

    the question is, does anyone know how to enable the air suspension in the 2618 OS or have a clean copy of the 12606961 OS?

    thanks
    JCC

    edit -found out 9691 is the update OS for 2618, so ive grabbed an escalade os copy to attemp to get the autoride running
    I don't believe the air ride is controlled by the PCM, but by the BCM, Body Control Module, at least it was in my old 2003 H2. I think you'll need a Tech2 to figure out what's keeping it from working.

  8. #23
    Carb and Points!
    Join Date
    Mar 2021
    Age
    42
    Posts
    5
    Quote Originally Posted by Pulse_GTO View Post
    I don't believe the air ride is controlled by the PCM, but by the BCM, Body Control Module, at least it was in my old 2003 H2. I think you'll need a Tech2 to figure out what's keeping it from working.
    completely agree that the BCM is what eventually controls the air ride, but there is something in the PCM OS has something to do with it, i swapped over to the Escalade bin and segment swapped in the lm7 and 4l80e, and suddenly the air suspension works.
    even during writing the PCM the cluster starting displaying messages about "service ride control" and "stability control".
    so at some level the PCM OS has to call the BCM over the serial bus to tell it air ride is available.

    but either way, it works now and felt great. right up until the tail shaft bushing ate the slip yoke and tossed another seal, lol. (i swapped my spare trans in and reused the other tail housing) just glad i caught it before it spun the bushing. always a new challenge with a frankenstien.
    thank you for the reply

  9. #24
    Carb and Points!
    Join Date
    Jul 2022
    Age
    24
    Posts
    4
    I have the OS 12606961. I understand this is the updated 12592618 5.3L. Could I use xdf of 618 for 6961? The only difference is two transmission changes from gm. The truck is a 2005 crew cab 5.3 w/ 4l60e. I would just like to remove vats, rear O2 sensors, and change differential so tach will be correct.

    After reading pcm I received a reduced engine power message on dashboard this wouldn't have been the cause correct?

    Any help would be appreciated
    Attached Files Attached Files
    Last edited by Ttrain32; 07-30-2022 at 06:02 AM.

  10. #25
    Fuel Injected! Pulse_GTO's Avatar
    Join Date
    Aug 2020
    Age
    45
    Posts
    174
    Quote Originally Posted by Ttrain32 View Post
    I have the OS 12606961. I understand this is the updated 12592618 5.3L. Could I use xdf of 618 for 6961? The only difference is two transmission changes from gm. The truck is a 2005 crew cab 5.3 w/ 4l60e. I would just like to remove vats, rear O2 sensors, and change differential so tach will be correct.

    Any help would be appreciated
    Would you be able to post the bin file?

  11. #26
    Carb and Points!
    Join Date
    Jul 2022
    Age
    24
    Posts
    4
    Yes I would have to wait till Thursday evening to post

  12. #27
    Carb and Points!
    Join Date
    Jul 2022
    Age
    24
    Posts
    4
    I have the OS 12606961. I understand this is the updated 12592618 5.3L. Could I use xdf of 618 for 6961? The only difference is two transmission changes from gm. The truck is a 2005 crew cab 5.3 w/ 4l60e. I would just like to remove vats, rear O2 sensors, and change differential so tach will be correct.


    Any help would be appreciated
    Attached Files Attached Files

  13. #28
    Carb and Points!
    Join Date
    Nov 2022
    Posts
    5
    i have a 1993 c1500 2wd and doing a ls swap . 2005 tahoe 5.3 460le doner. pcm is p59 os id 12592618 .this is the Compleat unit from the 2005 i have not changed anything. and i used the gas pedal as well is there a bin i can rewrite over to get me up and running ? any help is appreciated
    Attached Files Attached Files
    Last edited by ric; 11-26-2022 at 08:49 PM.

  14. #29
    Carb and Points!
    Join Date
    Dec 2022
    Posts
    3
    Is the PCM serial number at 0x4000?

  15. #30
    Carb and Points!
    Join Date
    Dec 2023
    Age
    22
    Posts
    4
    how do i download this to my computer so i can use it for my ecu

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •