2002 TunerPro Bin Files
2002 TunerPro XDF 12212156 OS
2002 TunerPro Bin Files
2002 TunerPro XDF 12212156 OS
1990 Chevy Suburban 5.7L Auto ECM 1227747 $42!
1998 Chevy Silverado 5.7L Vortec 0411 Swap to RoadRunner!
-= =-
'02Grand Prix GTP L67 os12223462.bin (512.0 KB) 2002 Malibu 3.4L osid 12588234.bin (512.0 KB)
'02 Chevy 2500 4x4 8.1 L18 os12216125.bin (512.0 KB)
'02 Chevy K1500 5.3L os12216125.bin (512.0 KB)
I can't open this in TunerPro because I don't have the definition file for it (27_06).
But I can open it in TunerCat, it uses definition 27_06.
Hi, im trying to download the bin file for 5.3 manual trans and it keeps coming through as a adobe document, I need it as a XDF file. any help?? thanks, Mark
Good night friend, I am very very new to tunerpro and I would like to learn a bit I have downloaded a bin file right now but I see that it is asking me for the XDF file which I do not have, I did not know I am in the right direction asking for help in this way or in estge forum place
The question is where do I get the XDF from, do I have to ask for it exactly for each ecu?
Hello all. We are performing a PCM upgrade for a customer from a 1996 black box Vortec PCM to a 2002 "0411" OS 12212156. Mainly to accommodate tire/gear changes, etc. Anywho. The project truck is fitted with a 5.0L Auto setup. Big deal right? Who cares about a 5.0L? Well, this customer does and we accommodate. I searched and was unable to locate a good 5.0L bin, especially for a 2002 OS. I broke down and "bought" a bin from GM via SPS2, flashed a spare PCM and voila, 2002 5.0L bin. Since I could not find a good 5.0L .bin, I am sharing the one I have with the world. Enjoy. I make no warranty expressed or implied, it is a stock GM binary.
Bill
edit: This binary is originally from a 2002 Express van 5.0L 2wd.
If it don't fit force it, if it don't force fit f&%@ it!
Can’t get the 2002 5.0L bin file to download. Any other way to get this file?
Last edited by a_a_ron.g556; 03-01-2022 at 08:19 PM.
I have a 411 PCM and I used PCM Hammer to update it to the 2156 OS. I am swapping a Gen 3 5.3 V8 with 4L80 into a Dodge. I would like to segment swap the 4L80 portion since that combo was never sold by GM. I see the only 2156 file with a 4L80 here is for a pre-LS (L31) Express van. Can I use that file for the segment swap?
Thanks.
UPDATE
I used LS Droid to segment swap the Van 4L80 file (see below), and PCM Hammer to write it to my 411 PCM- no errors. I did the transmission and transmission diagnostics. The base file was the 2002 Silverado 5.3 DBC no EGR from post #8, I modified it by changing the tach output from 6/6 to 3/3 and disabled some MIL codes for the rear O2 sensors. I'll update here if it works, I'm still a ways from starting my swapped engine. I'm attaching the new bin file.
UPDATE #2
When I checked the segment swapped file with HP Tuners, it showed as backwards- the engine was a 5.7 not 5.3, and the trans was a 4L60, not 4L80. As such, I don't think this file is usable as-is.
UPDATE #3
I found my error was in LS Droid. I presumed the green button meant you were swapping that function, and the red one meant you were not. That's backwards. I deleted the file until I can fix it.
UPDATE #4 11/7/20
Updated file attached. My truck developed a mechanical problem (oil leak), but the tune allowed it to run OK. As I recall, it has a number of MIL codes disabled such as EGR and secondary O2 sensors, AC and VATS are disabled, and the tach hi/low resolutions were modified. I was not able to drive the truck to verify the trans shifted properly, so use at your own risk. It did show up as a 5.3/4L80 in HP Tuners though.
Last edited by 95_C4; 11-08-2020 at 01:41 AM. Reason: Attached corrected file
Bookmarks