bank 2 (red) & lean bank 1 (yellow)

[30bird]

I am a noob first swap learning on the go so if I say something ignorant it is because I have never done this before.
I am running a 12212156.bin (from BoredTruckOwner) I customized with a licensed copy of TuneProRT flashed with LS Droid and a OBDXpro.
1. The truck runs rough at cold start with the 12212156 tune

2. I keep getting lean bank 2 (red) & lean bank 1 (yellow) not sure what is going on but I am thinking it is the 12212156 tune

When I run the original LM7 9373372 tune it lifter rattles at start but runs smooth
I get no lean codes (I do get O2 bank 1 sensor 2)
Since 12212156 is written for a stock 2002 LM7 and this is a stock 1999 LM7, Maybe there are differences in the fuel systems?

other changes
unchecked B1901 - Maximum Allowed Engine Torque under toque limiting


P1638 Alternator ‘F’ terminal -circuit malfunction Wiring open circuit/short circuit to ground, alternator, ECM
P1638 3 0 Battery light on Message center Not present in 1999

Oxygen sensor
P0137 Heated oxygen sensor (HO2S) 2, bank 1 -low voltage Exhaust leak, wiring short to earth, H025, ECM
P0138 Heated oxygen sensor (HO2S) 2, bank 1 -high voltage Wiring short to positive, H025, ECM
P0139 Heated oxygen sensor (HO2S) 2, bank 1 -slow response Heating inoperative, wiring, H028
P0140 Heated oxygen sensor (HO2S) 2, bank 1 no activity detected Wiring, heating inoperative, H028, ECM
P0141 Heated oxygen sensor (HO2S) 2, bank 1 heater control circuit malfunction Wiring, H025, ECM
P0157 Heated oxygen sensor (HO2S) 2, bank 2 -low voltage Exhaust leak, wiring short to earth, H028, ECM
P0158 Heated oxygen sensor (h025) 2, bank 2, -high voltage Wiring short to positive, HO2S, ECM
P0160 Heated oxygen sensor (H025) 2, bank 2 -no activity detected Wiring, H028, ECM
P0161 Heated oxygen sensor (HO2S) 2, bank 2, heater control -circuit malfunction Wiring, HO2S, ECM
P0167 Heated oxygen sensor (HO2S) 3, bank 2, heater control circuit malfunction Wiring, HO2S, ECM

EVAP

P0442 Evaporative emission (EV AP) system -small leak detected Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve
P0443 Evaporative emission (EVAP) canister purge valve circuit malfunction Wiring, EVAP canister purge valve, ECM
P0444 Evaporative emission (EVAP) canister purge valve open circuit Wiring open circuit, EVAP canister purge valve, ECM
P0446 Evaporative emission (EVAP) system, vent control -circuit malfunction Wiring, EVAP canister purge valve, ECM
P0449 Evaporative emission (EVAP) system, vent valve circuit malfunction Wiring, EVAP canister purge valve, ECM
P0452 Evaporative emission (EVAP) pressure sensor -low input Wiring short to earth, EVAP pressure sensor, ECM
P0453 Evaporative emission (EVAP) pressure sensor high input Wiring short to positive, EVAP pressure sensor, ECM
P1410 Evaporative emission (EVAP) canister purge valve -circuit malfunction Wiring, poor connectios, EVAP canister vent valve, ECM
P1441 Evaporative emission (EVAP) system -leak detected Hose connection(s), EVAP canister, EVAP canister purge valve

[30bird]

solved
https://pcmhacking.net/forums/viewto...118001#p118001