Search:

Type: Posts; User: Tom B.

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Thank you for picking up the ball after Moates...

    Thank you for picking up the ball after Moates put it down. I have purchased a lot of products from them over the years. I wish they would've given their customers a heads up.
  2. Replies
    5
    Views
    3,648

    I never saw the question. I would have done it...

    I never saw the question. I would have done it directly. I will do it asap. I couldn't do anything on this site for a week. Every time I attempted to post, i got the message asking me if I wanted to...
  3. Replies
    5
    Views
    3,648

    Here is a screen shot of what I am dealing with. ...

    Here is a screen shot of what I am dealing with. I've been trying to upload this for a week.
  4. Replies
    5
    Views
    3,648

    17046

    17046
  5. Replies
    5
    Views
    3,648

    MEFI5 Can Bus error

    In the MEFI 5 system does anyone what the [#220] error represents?
  6. Replies
    8
    Views
    4,624

    *UPDATE* Turned out to be a bad box. Ken shipped...

    *UPDATE* Turned out to be a bad box. Ken shipped a replacement air mail. They stand behind their product.
  7. Replies
    8
    Views
    4,624

    Still having com port issues

    Here are the two errors when using the program. Does anyone have a working version of the executable that you can share?
    :mad1:

    with the cable plugged into a usb port
    run-time error '8002':...
  8. Replies
    8
    Views
    4,624

    Thank you. This is what I have been trying to...

    Thank you. This is what I have been trying to get for 3 weeks.
  9. Replies
    8
    Views
    4,624

    I'm sending up a flare. I have purchased both...

    I'm sending up a flare. I have purchased both the MEFI 1-4 Scan and tune software and the MEFI 5 software. The latest MEFI software on the the thumb drive does notwork and does not have install...
  10. Replies
    5
    Views
    2,657

    You need the cam sensor. If you have to do the...

    You need the cam sensor. If you have to do the crank sensor re-learn, you need to ground the parking brake pinout. The PCM won't do the re-learn without the ground signal. I'll have to look at my...
  11. Replies
    12
    Views
    4,077

    You should be fine with them in the collectors....

    You should be fine with them in the collectors. Back to basics, do you have a leaky flange gasket? That will pull air into the exhaust and create a lean reading at the O2 sensor.
  12. Replies
    8
    Views
    4,624

    MEFI 5. I'm only interested in doing one boat for...

    MEFI 5. I'm only interested in doing one boat for a friend. I was hoping not have to spend the big cash on the software. (I know... B.O.A.T. means "bust out another thousand"). I have TunerPro,...
  13. Replies
    8
    Views
    4,624

    Anyone tuning MEFI systems with TunerPro?

    Has anyone done any tuning with the MEFI systems using TunerPro?
  14. Never-mind, I found one.

    Never-mind, I found one.
  15. Gen IV LS engine VVT cam phaser/cam sensor wiring harness pinout

    Does anyone have a copy of the schematic for the proper pinout sequence for the harness? I am working on a 6.0 in a boat and some dummy pulled the wires out of the connector. The boat side of the...
  16. You may have a mechanical problem with the PWM...

    You may have a mechanical problem with the PWM valve and bore wear in the valve body. Another issue may be that the PWM (95-newer) transmissions use a different tcc spool valve in the pump. If your...
  17. Replies
    824
    Views
    746,381

    The Delteq does use a Northstar module and coils.

    The Delteq does use a Northstar module and coils.
  18. Replies
    824
    Views
    746,381

    You need to use the 96-97 cover. The crank damper...

    You need to use the 96-97 cover. The crank damper mount is also shorter to accommodate the trigger wheel.
  19. Replies
    10
    Views
    8,350

    I'm glad you didn't have any major damage.

    I'm glad you didn't have any major damage.
  20. Replies
    10
    Views
    8,350

    Try to turn the crankshaft using a socket and...

    Try to turn the crankshaft using a socket and ratchet/breaker bar on the balancer bolt. If the engine will turn fairly smooth you should be OK. I would definitely put some lightweight oil in it and...
  21. Replies
    10
    Views
    8,350

    Did you shut the ignition off or did the engine...

    Did you shut the ignition off or did the engine lock up?
  22. Replies
    824
    Views
    746,381

    The Opti without the high voltage running through...

    The Opti without the high voltage running through it will be just fine. Just clean it up and seal it. The same sensors seem to run forever in the other cars they are installed in.
  23. Replies
    824
    Views
    746,381

    I will say this once and then I am done with it. ...

    I will say this once and then I am done with it. Valve overlap has a lot to do with the way it affects how an engine runs. If your position is to the contrary, I can only surmise you are less...
  24. Replies
    824
    Views
    746,381

    Hey now! We did get a little off topic for a...

    Hey now! We did get a little off topic for a minute. Anyways, I am committed to help you guys find a good, reliable, economical solution. I'm sure Fast 355 will be just as generous with his time...
  25. Replies
    5
    Views
    4,841

    You can get the hardware/software you need from...

    You can get the hardware/software you need from Moates.net and tunercat.com Don't bother with anything from Jet.
Results 1 to 25 of 52
Page 1 of 3 1 2 3