I see some clarification might be required when converting a ‘7730 V6 Memcal to V8.
1. Install jumper into '7730 V6 Memcal, no other '7730 V6 Memcal modification needed or required.
2. Install...

Make sure the ALDL cable is plugged into the laptop before installing the ALDL cable driver.

Sometimes Windows will automatically install the ALDL cable driver the first time the ALDL cable is...

I suspect there might be a knock frequency difference between the V6 Memcal Knock Filter board vs. V8 Memcal Knock Filter board.

I use the 1227730 V8 TPI 4K knock sensor after modifying the V6...

Possibly definition $9A: http://www.gearhead-efi.com/Fuel-Injection/showthread.php?1370-OBD1-Scanning-Datalogging-94-TBI-5-speed-manual

More Information, How to connect ESC module in place of a Memcal knock filter see attached.

There is the option to convert a ‘7730 V6 Memcal to a ‘7730 V8 Memcal.

http://www.gearhead-efi.com/Fuel-Injection/showthread.php?6796-TPI-350-with-V6-Memcal-fuel-mod-quetions

19871

19872
...

Possibly an ESC Module is required.

The picture below is for TBI not TPI and is for reference only, do not use as a wiring diagram.

1227730 TPI did not use an external ESC Module, but many TBI...

The learning curve can be steep with Tuning.

"A Tiger can kill an Elephant . . . One Byte at a Time" is a good approach to learn tuning.

For the first Byte I recommend is coming up to speed...

:welcome:

19861

Gearhead-efi link with tuning information for chip code BJKW: http://www.gearhead-efi.com/Fuel-Injection/showthread.php?337-16196395-PCM-Information-OE

TunerPro RT software...

I'm thinking the main difference between the 19186079 and the 16147525 is obviously the hexadecimal address in the chip and the associated electronics inside the computers.

For example,
1987 ~...

Interesting thread:

http://www.gearhead-efi.com/Fuel-Injection/showthread.php?7284-Looking-for-a-ECM-for-a-old-GMC-Topkick&highlight=16147525

19858
The installation of the GM2 likely OK. The soldering required for the GM2 is basic through hole soldering. An ohm meter can be used to test for solder bridges between pins, which might cause...

ECM 16147525 Uses a 4K chip, 24 pin. Is this original computer part number and chip for your Topkick?

The 27SF512 chip is a 64K chip, 28 pin. What chip adapter 24 pin to 28 pin is being used?
...

When an engine briefly runs after pouring fuel into the throttle body indicates a fuel problem.

Possibly the rapid flashing check engine light is bad chip.

I favor troubleshooting the rapid...

I posted the files in the linked thread, which I personally verified before posting them.

I'm curious what the Noid light testing for the injector wiring revealed?

I am hoping someone might know how many Pulses per Mile the 6L80E REPLICATED TOS SIGNAL Pin 16 is?

Maybe 4000 / 8000 / 16000?

Thanks in advance,

dave w

Are the posted instructions for the AEM 30-4110?

The AEM 30-4110 is Plug-n-Play with the '7427 WBO2 setup, no calibrations / no adjustments are required.

:welcome:

What engine are you planning to put a turbo on?

:welcome:

Installing a chip that has been programmed with the edits is required.:thumbsup:

http://www.gearhead-efi.com/Fuel-Injection/showthread.php?391-1227727-1227730-ECM-Information-A1

I think using a ‘7730 / ‘7727 V6 Memcal is a good plan.

Link for WBO2 tuning using the 16197427 PCM: http://www.gearhead-efi.com/Fuel-Injection/showthread.php?5381-WBO2-Tuning-Spreadsheet

19825

I think a 4K VSS is a very poor option because the Speed Pulse Per Rev number will be extremely low. The 8K VSS already has a low Speed Pulse Per Rev number and is likely the lowest cost option too.

Chip code BBNT is for a 1993 4.3 CPI, definition $E6

19818

19820