Search:

Type: Posts; User: tayto

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    103
    Views
    2,061

    throttle shafts probably need bushings

    throttle shafts probably need bushings
  2. Replies
    22
    Views
    2,536

    been waiting to hear your opinion on the Holley...

    been waiting to hear your opinion on the Holley exhaust manifolds. i like the heat shields on the exhaust manifolds, looks good!
  3. Replies
    8
    Views
    811

    steveo, I may be remembering wrong but are you on...

    steveo, I may be remembering wrong but are you on vancouver island?
  4. Replies
    11
    Views
    836

    i normally just change shift points in the tune....

    i normally just change shift points in the tune. if i want a softer or firmer shift i play with orifice sizes in the separator plate. usually tuners get into trouble when they start messing with...
  5. Replies
    11
    Views
    836

    you should really be doing internal mods if you...

    you should really be doing internal mods if you want to increase pressure ie: pressure relief&boost valve. you can crank up the pressure in the tune but it's only going to go as high as what the...
  6. Thread: Stupid question

    by tayto
    Replies
    5
    Views
    421

    i have a few sets of tbi injectors i harvested...

    i have a few sets of tbi injectors i harvested probably 15 years ago that still have the paint on them. this was back when no one wanted this stuff and lower milage units were not hard to come by in...
  7. Replies
    15
    Views
    2,183

    lol ok

    lol ok
  8. Replies
    15
    Views
    2,183

    EBL comes with stock calibrations. It also is a...

    EBL comes with stock calibrations. It also is a GM ECU so adjustments are the same as any other GM ECU of that era. If you couldn't figure EBL out I doubt Emulation and burning your own chips will go...
  9. Replies
    11
    Views
    836

    do some research on the LS guys that use...

    do some research on the LS guys that use HPTuners, i think they like to set the shift time from 0 to 0.3. Don't quote me on those numbers. I know for 4L60E short shift times will lead to longer life,...
  10. Replies
    4
    Views
    478

    get the wiring diagrams for both vehicles and...

    get the wiring diagrams for both vehicles and figure it out. diagrams are on this forum if you look.
  11. Replies
    7
    Views
    1,184

    there was an excellent write up done by 84elky on...

    there was an excellent write up done by 84elky on this forum not to long ago about injector offsets. you will see more power gains and a smoother running engine with a set of flow matched injectors.
  12. Replies
    13
    Views
    3,063

    the pressure dropping to 0 psi on a TBI system...

    the pressure dropping to 0 psi on a TBI system after shutdown is normal. there's actually a bleed off orifice in the regulator. this is not like "modern" EFI.
    ...
  13. Thread: 7747 to 7427

    by tayto
    Replies
    33
    Views
    4,685

    no TBI ecm/pcm requires a 40ppr signal directly....

    no TBI ecm/pcm requires a 40ppr signal directly. i believe either 2000 or 4000 ppm and can be selected in the calibration. you're VSSB is in the speedo housing IIRC.
  14. Replies
    13
    Views
    3,063

    did you use the correct submersible fuel hose on...

    did you use the correct submersible fuel hose on the pump? you can't use normal fuel hose, it will eventually swell and not hold pressure
  15. Replies
    4
    Views
    976

    I have seen '7427 in 4L80E trucks, this is...

    I have seen '7427 in 4L80E trucks, this is nothing new/unusual.
  16. Replies
    2
    Views
    776

    i believe there's a 454 manual transmission cal I...

    i believe there's a 454 manual transmission cal I would start there.
  17. Replies
    3
    Views
    998

    send them off and get professionally cleaned...

    send them off and get professionally cleaned &flowed. i too have found used oem better than aftermarket.
  18. Replies
    8
    Views
    1,244

    what # on the connector does the SES ground wire...

    what # on the connector does the SES ground wire goto? should be A5...
  19. Replies
    26
    Views
    3,905

    good stuff

    good stuff
  20. Replies
    14
    Views
    2,037

    i think 95 was when the s10 changed body style n

    i think 95 was when the s10 changed body style n
  21. Replies
    26
    Views
    3,905

    https://www.permatex.com/products/thread-compounds...

    https://www.permatex.com/products/thread-compounds/thread-sealants/permatex-high-performance-thread-sealant-50-ml/

    this a real thread sealant. i use it on everything automotive from head bolts...
  22. Replies
    26
    Views
    3,905

    ya i use the yellow "gas" teflon tape or actual...

    ya i use the yellow "gas" teflon tape or actual thread sealant. I used that aviation form a gasket stuff in my younger days, but it doesnt seem to hold up well to oil.
  23. Replies
    26
    Views
    3,905

    ya there is 3 possible places it could leak from,...

    ya there is 3 possible places it could leak from, where it goes into the fuel pod, where the hardline threads into or one of the ports to hook a fuel gauge up to. i have not used this fitting but...
  24. Replies
    26
    Views
    3,905

    did you make sure the small plastic seal was on...

    did you make sure the small plastic seal was on the end?
  25. if you want to invest the time go for it but I...

    if you want to invest the time go for it but I don't think the gains will be as significant as one might think. usually you leave the floor of the runner alone unless you are changing the shape of...
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4