Search:

Type: Posts; User: In-Tech

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    4
    Views
    398

    Prog ID BCC Size Year Release Date Eprom ECM Prom...

    Prog ID BCC Size Year Release Date Eprom ECM Prom ID Scan ID Platform Engine Disp. Trans Trans Type Gear Ratio


    BBMD 1993 33702 16179257 16168625 9258 9291 C1 L05 5.7 M30 AUTO GT4
  2. Replies
    88
    Views
    18,316

    Thanks Tom, I mentioned PM in case you didn't...

    Thanks Tom,
    I mentioned PM in case you didn't want if public. Man, shit ton of equates in there :happy: I'll have a gander tomorrow :)
  3. Replies
    88
    Views
    18,316

    Hiya Tom, I will have to dig to find this older...

    Hiya Tom, I will have to dig to find this older stuff. I'm surprised you are using MotS, Intel hex has always seemed good but I have never worked with your box. If you would like, PM me the code to...
  4. Replies
    7
    Views
    692

    Very common smog problem with ANTY. Double...

    Very common smog problem with ANTY.

    Double check chip orientation. Dimple in chip needs to match dimple in holder.
  5. Replies
    88
    Views
    18,316

    Hi Tom, Yeah, I was having a little fun about...

    Hi Tom,
    Yeah, I was having a little fun about the substrate :) This situation has no worries, it just reminded me when I wrote a "burner" to test. The spec sheet said it was only good for ~100,000...
  6. Replies
    88
    Views
    18,316

    Hahaha, chanting :laugh: Back in the 90's I ran...

    Hahaha, chanting :laugh:
    Back in the 90's I ran some tests on some TMS370 stuff, brutally burning the bit flips from 00h-FFh and it took ~30,000,000 cycles before partial failure. Adding that short...
  7. Replies
    88
    Views
    18,316

    I'll say a small prayer for the substrate. ...

    I'll say a small prayer for the substrate. :laugh: :happy:
  8. Replies
    1
    Views
    676

    Hiya, I'll take them if willing. Shipping to...

    Hiya,
    I'll take them if willing. Shipping to 93710 USPS priority preferred.
  9. Replies
    88
    Views
    18,316

    Hiya Tom, At a glance, the SLOOP is an...

    Hiya Tom,
    At a glance, the SLOOP is an incredibly tight loop especially in eeprom and not flash.
    In my mind, if you have room, I am thinking a JSR to use some ticks as well as more ticks using the...
  10. Replies
    32
    Views
    33,237

    Sticky: Thanks guys, front page updated :)

    Thanks guys, front page updated :)
  11. Replies
    32
    Views
    33,237

    Sticky: Hiya's Does anyone have a new code? P.S....

    Hiya's
    Does anyone have a new code?

    P.S. Found on the interweb
    255076685227989677
  12. Replies
    5
    Views
    443

    Hiya, You're missing the point. We used vortec...

    Hiya,
    You're missing the point. We used vortec pumps(58psi) to replace the tbi pumps all the time, the regulator is what controls the pressure, not the pump. A 60psi CAPABLE pump will still make...
  13. Replies
    11
    Views
    836

    Hiya's The "adaptives" basically don't work in...

    Hiya's
    The "adaptives" basically don't work in these early computers. I wouldn't set anything under .25 in those fields either way. Adjust everything in the pressure tablles and/or in the force...
  14. Thread: hi

    by In-Tech
    Replies
    2
    Views
    374

    :welcome2:

    :welcome2:
  15. Replies
    12
    Views
    771

    Hiya, Does this have stock injectors or...

    Hiya,
    Does this have stock injectors or aftermarket replacements? I've only seen this happen with aftermarket and high fuel pressure as they are then slow to respond. That big manifold and spacer...
  16. Replies
    59
    Views
    10,216

    Good call steveo :)

    Good call steveo :)
  17. Replies
    59
    Views
    10,216

    ^^^^^ This! Just moving an old harness can...

    ^^^^^ This!
    Just moving an old harness can "break" it :( So many hot/cold cycles and it will live a very long time, till it moves.
  18. Replies
    18
    Views
    2,754

    Hiya, I don't know if it matters in this mask. ...

    Hiya,
    I don't know if it matters in this mask. I have always found most GM stuff requires the tps voltage to be between .5-.6v for idle control to work correctly. Most times with big cams that...
  19. Hiya, Interesting how I cannot read the source...

    Hiya,
    Interesting how I cannot read the source file. I can already beat up ANY e38, your files are suspect, hate to say if you are actually contributing.
  20. Thread: LT1 Caddy Fun

    by In-Tech
    Replies
    1
    Views
    226

    :welcome2:

    :welcome2:
  21. Wow, good data. Thanks Dave :)

    Wow, good data.
    Thanks Dave :)
  22. Replies
    32
    Views
    33,237

    Sticky: Thanks given to MO LS for sharing, credit given...

    Thanks given to MO LS for sharing, credit given in OP, it's nice to see this thread grow, thanks to sledhead2 too :)
  23. Ok, cool Sounds like you have a grasp on the...

    Ok, cool
    Sounds like you have a grasp on the struggles ahead :)
  24. If iirc a fmu is about 1.25:1 Your real struggle...

    If iirc a fmu is about 1.25:1
    Your real struggle will be to find large enough injectors for the TBI. There was a time I had to use BBC 75's @ 12lb injectors and then use a 3:1 regulator. Figure...
  25. Hello, A "boost-a-pump" increases the flow, the...

    Hello,
    A "boost-a-pump" increases the flow, the pressure has to rise at least 1:1 vs. Meaning if base pressure is 12, at 10 lbs boost the fuel pressure needs to be 22 to maintain the flow. Any...
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4