Search:

Type: Posts; User: 57210

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    3,552

    I have the HPT file itself. Can I use LSDroid to...

    I have the HPT file itself. Can I use LSDroid to load it on my dummy ecm?
    I tried it with LS Droid and found that the file wasn’t compatible.
  2. Replies
    7
    Views
    3,552

    Could I use LSDroid to load and then read it back?

    Could I use LSDroid to load and then read it back?
  3. Replies
    7
    Views
    3,552

    Change HPT file to BIN

    Is there an easy way to change a HPT file to a BIN file?
  4. Thread: LQ9 VE tables

    by 57210
    Replies
    0
    Views
    1,229

    LQ9 VE tables

    Looking for the LQ9 VE tables. Are they much different from the LQ4 tables?
  5. Thread: Change OS

    by 57210
    Replies
    5
    Views
    2,308

    Is the VIN tied to a specific OS? Will my VIN...

    Is the VIN tied to a specific OS? Will my VIN work if I change the OS?
  6. Replies
    82
    Views
    87,811

    Did you ever find one?

    Did you ever find one?
  7. Thread: Change OS

    by 57210
    Replies
    5
    Views
    2,308

    Change OS

    I have a 2002 Escalade 6.0 AWD with OS 12209203. There isn't a XDF for this OS that I can find. Can I change the OS to something with a XDF file available without messing up the BCM stuff? Thanks for...
  8. Replies
    3
    Views
    3,039

    Rick I am wanting to be able to change some...

    Rick I am wanting to be able to change some things on my 02 Escalade. I'll need a TunerPro XDF and I don't think there is one for the 12209203.
  9. Replies
    3
    Views
    3,039

    Substitute for OS 12209203

    I've got a P01 from a 2002 Escalade. Is there a good substitute OS that has a XDF for it?
  10. Replies
    6
    Views
    18,527

    I have a 2K sender from JTR. Can I just splice...

    I have a 2K sender from JTR. Can I just splice into the A10 lead for the speedometer?
  11. Replies
    6
    Views
    18,527

    VSS

    I have the EBL Flash-II
    The speedometer needs 12v
    Input 3K-100K per mile Hall effect sensor or magnetic sensor
  12. Replies
    6
    Views
    18,527

    Electric speedometer hookup

    Can I use the VSS signal for the SW electric speedometer? If so where do I tap into it?
  13. Replies
    1
    Views
    16,130

    Found my problem?

    I put an EBL in my 48 Willys wagon with a vortec 5.7 and a TBI. I spoke with you several time , trying to figure out why it was using so much gas. I finally decided to change the rear end ratio to a...
  14. Replies
    1
    Views
    20,002

    Code 59 still active?

    I am trying to get registered at Code 59 website, but have been unable to receive an activation code. Does anyone know if the site is still active?
    Thanks for any info you might share.
  15. Replies
    2
    Views
    15,451

    The OS is 12212441

    The OS is 12212441
  16. Replies
    2
    Views
    15,451

    Trying to find XDF and ADX for 0411

    14524
  17. Replies
    1
    Views
    2,973

    Terminals for 16197427 connectors

    Does anyone have a good source to get terminals to redo the ECM connectors on a 16197427?
  18. Thread: Turn EGR back on

    by 57210
    Replies
    4
    Views
    5,231

    I was looking at the BIN with $42-1227747-V5.9.3...

    I was looking at the BIN with $42-1227747-V5.9.3 XDL and $42-1227747-V5.2 ADX in TP. I loaded up the 42 XDL and 42 ADX and got the same figures that you did.
    Thanks for your input
  19. Thread: Turn EGR back on

    by 57210
    Replies
    4
    Views
    5,231

    I opened two stock bins and they ere the same....

    I opened two stock bins and they ere the same. That's why I was looking to see what hey sholdbe set at.
  20. Thread: Turn EGR back on

    by 57210
    Replies
    4
    Views
    5,231

    Turn EGR back on

    I need to turn the EGR back on for emission testing. Three things that I'm not sure where they need to be set.
    EGR Min TPS to allow EGR on mine is set at 80%
    EGR On Low VAC Kpa ...
  21. Thread: $42 VE2 table?

    by 57210
    Replies
    4
    Views
    5,141

    I went back and added VE2 figures to the VE1...

    I went back and added VE2 figures to the VE1 table. After I zeroed out the VE2 table, I closed it and reopened it and all the RPMs had 5.08 for a correction factor.
    I zeroed it again and came up...
  22. Thread: $42 VE2 table?

    by 57210
    Replies
    4
    Views
    5,141

    Thanks for the info. I've read that thread, but I...

    Thanks for the info. I've read that thread, but I was trying to find out where these number in VE2 come from
  23. Thread: $42 VE2 table?

    by 57210
    Replies
    4
    Views
    5,141

    $42 VE2 table?

    How is this table populated? Someone said that there was a sticky by Rbob that explains the different tables.
    Thanks for any info
  24. Replies
    17
    Views
    48,764

    I'm trying to set up a history table for my VE...

    I'm trying to set up a history table for my VE tuning. I've got
    ARJT BIN
    XDF $42-1227747-V5.9.3
    ADX $42-1227747-V3T
    When I get to the step to click on the Output Z, My browser box is empty....
  25. Replies
    23
    Views
    17,160

    I wanted to say Thanks for all the help with...

    I wanted to say Thanks for all the help with this. I finally found that the ECM I used for this was bad. I got another one and soldered it up this morning all the chips I burned seem to come up fine....
Results 1 to 25 of 42
Page 1 of 2 1 2