Search:

Type: Posts; User: Chutchcroft

Search: Search took 0.00 seconds.

  1. Auto Prom APU 1, Throttle Body 454 Stock, SPR Throttle Body Bored 54mm

    Seeing if there is any interest in these.

    Thanks
  2. Replies
    3
    Views
    21,131

    Hi Dave, I know. You helped tune this truck on...

    Hi Dave, I know. You helped tune this truck on OBD1 with TBI. I think I am just reaching my limit with OBD and 750CFM. I think I am going to Sell the TBI Setup and go Holley.
  3. Replies
    3
    Views
    21,131

    This Truck is getting a Holley Terminator X Max...

    This Truck is getting a Holley Terminator X Max integrated with the factory ECM. I will be using the factory ECM for factory gauges primarily.
  4. Replies
    1
    Views
    10,721

    This Truck is getting a Holley Terminator X Max...

    This Truck is getting a Holley Terminator X Max integrated with the factory ECM. I will be using the factory ECM for factory gauges primarily.
  5. Replies
    18
    Views
    18,874

    This Truck is getting a Holley Terminator X Max...

    This Truck is getting a Holley Terminator X Max integrated with the factory ECM. I will be using the factory ECM for factory gauges primarily.
  6. Replies
    3
    Views
    21,131

    454 TBI Build

    http://www.gearhead-efi.com/Fuel-Injection/showthread.php?8123-1995-K2500-454-4L80E

    This is a link to my build.

    I could use some help tuning this beast!

    Thanks
  7. Replies
    18
    Views
    18,874

    454X4 BUILD SHEET Bottom end all new gaskets...

    454X4 BUILD SHEET

    Bottom end all new gaskets and seals, bearings, rings, Melling HV Oil pump.

    Cloyes Billet Double Roller Chain.

    Harland Sharp 1.7 Rockers

    Lunati Voodoo Roller Cam
  8. Replies
    18
    Views
    18,874

    The 454x4 Lives!

    Finally got the engine put in. I took my time and got the break-in done yesterday. No leaks!

    Its time for all the help you can give me. I am attaching my Stock Bin and Modified Bin as well as the...
  9. Replies
    18
    Views
    18,874

    Well things took a turn for the worse. Turns...

    Well things took a turn for the worse.

    Turns out my COMP Flat Tappet cam is wiped out. Also, the COMP crank timing gear was cracked and missing a tooth.

    Sooo... I pulled the engine, re-ringed,...
  10. Replies
    18
    Views
    18,874

    Initial disassembly 14510 Fan Install ...

    Initial disassembly

    14510


    Fan Install

    14513

    Performer Heads Before Shop
  11. Replies
    18
    Views
    18,874

    Heads are back from the shop. New stainless...

    Heads are back from the shop. New stainless valves, new locks and retainers, comp springs, 3 way valve job.

    I also opted for the Flex-A-Lite 280 Monster fan.

    Spent a day or so getting wiring...
  12. Replies
    18
    Views
    18,874

    Pre 94 used a vacuum EGR. 94-95 is electronic...

    Pre 94 used a vacuum EGR. 94-95 is electronic with a different mounting profile. They possibly did make a 94-95 TBI intake, but don’t offer it anymore.

    My heads are large oval and I would be...
  13. Replies
    18
    Views
    18,874

    This makes good sense. I will be starting with a...

    This makes good sense. I will be starting with a clean read of the factory MEMCAL: BMHM. (really just curious if my 200$ for that chip did anything all this time)



    The heads and intake have...
  14. Replies
    18
    Views
    18,874

    1995 K2500 454/4L80E Build

    Hello All!

    Building up a 1995 K2500 for pulling the boat to the lake and general romping around town.

    Truck is Extended Cab, Long Bed, 8600GVW, 454/4L80E, 6" Lift, 35x12.5 Tires, 4:10 gearing...
  15. Replies
    1
    Views
    10,721

    1995 K2500 454/4L80E

    Hello,

    Florida guy here. Long time BBC guy. Moving into tuning this thing as I out build my current chip.

    I will need help and advice!

    Thanks to all of you.

    -Hutch
Results 1 to 15 of 15