Search:

Type: Posts; User: Snipescastle2

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    1,210

    Bad 0411 PCM?

    Hello all! I’ve been beating my head against the wall with my ‘96 Trans Am
    LT1 0411 PCM swap.
    a year ago, February, after successfully doing the swap, I was returning home from
    work one night,...
  2. Replies
    21
    Views
    19,888

    Hello all, been trying to get over this Dreaded...

    Hello all,
    been trying to get over this Dreaded "covid" thing, been lucky up till now. two years and never caught it, guess my luck had run out. IO had all but given up on the firebird 0411 swap,...
  3. Replies
    0
    Views
    1,011

    GM four pin Oil Pressure sender wiring

    Hello all! I’m at it again with the 0411 PCM swapped LT1,
    got everything installed, got fuel, it cranks, but no fire.
    a little about what has happened since I first started driving
    with this PCM...
  4. Replies
    6
    Views
    2,789

    Ok, yesterday I replaced both of my O2 Sensors, I...

    Ok, yesterday I replaced both of my O2 Sensors, I think my bank one sensor wire harness has a break in one of
    The leads between the PCM and the sensor.
    But I got the bank two sensor reading like...
  5. Replies
    21
    Views
    19,888

    No, as a matter of fact, replacing the plugs and...

    No, as a matter of fact, replacing the plugs and O2 Sensors today, I dont have much time to work on my car as I’d like, so Sundays are it. Hoping I get some results today.I’ll post later on what I...
  6. Replies
    6
    Views
    2,789

    Thank you all for the replies. I will add the...

    Thank you all for the replies. I will add the grounds to the two pins, (26&29) and just so you know, I was reading “4.5 volts” at the high signal pin wire(purple /white wire at pin 69 C1 blue...
  7. Replies
    6
    Views
    2,789

    0411 PCM voltage going to O2 sensors?

    Hello everyone! I have a question with regards to 0411 PCM's. As many of you know, I converted my Trans Am with a 0411 PCM for my LT1. I have been having issues with my O2 sensors. the bank 1 sensor...
  8. Replies
    6
    Views
    5,287

    Hello all! I tried adding the ground to the PCM...

    Hello all! I tried adding the ground to the PCM but I still get the dtc saying no activity at the R/H O2 sensor. Now, if I take the same O2 sensor, place it in a vise, and run a propane torch across...
  9. Replies
    6
    Views
    5,287

    Hello again everyone! Just wanted to post my...

    Hello again everyone!
    Just wanted to post my findings to my latest problem(O2 sensor not reading)
    I was researching “testing Isolated Ground O2 Sensors” I found a post on another
    Website :
    ...
  10. Replies
    6
    Views
    5,287

    Carl, I drove the car today, it runs so much...

    Carl,
    I drove the car today, it runs so much better, but even after changing the bank 2 O2 sensor, it still doesn't read the sensor. I tested the sensor off the car to make sure it works, and it...
  11. Replies
    6
    Views
    5,287

    Carl, Yeah, I do, but I thought it might help...

    Carl,
    Yeah, I do, but I thought it might help someone else looking
    For a solution for just that problem, they wouldn’t have to search tons of posts
    to find an answer.
    Ben
  12. Replies
    6
    Views
    5,287

    Adding IAC gauge to .ADX file

    Hello everyone! I would like to know how you add the IAC counts to an ADX file?
    I saved many .ADX files, and have a few “Dashboards” saved, but none that show
    the “IAC counts” when I did my first...
  13. Replies
    21
    Views
    19,888

    Hello again! I’ve replaced my non functioning O2...

    Hello again! I’ve replaced my non functioning O2 sensor(bank 2 sensor 1) and I’m going to
    do more data logging tomorrow. While driving the other day, and even when the engine was
    idling, it was...
  14. Replies
    21
    Views
    19,888

    Hello everyone! Just wanted to update everyone...

    Hello everyone!
    Just wanted to update everyone on what I’ve accomplished so far. I finally found the reason
    my engine was running so rough, and I am embarrassed to say, I had a “Brain Fart” while...
  15. Replies
    21
    Views
    19,888

    Hello all! Just thought I’d post an update to my...

    Hello all!
    Just thought I’d post an update to my project. After chasing gremlins for the better part
    Of the last week, I figured out two problems with my setup.
    1.) I’m sure everyone has witnessed...
  16. Replies
    21
    Views
    19,888

    LT1 0411 tuning quest continues.....

    Hello everyone! I’m still trying to wrap my head around this project,
    it feels more like I’m getting “Wrapped around the axle” I’m reading more
    about spark tables and advancing/retarding the...
  17. Replies
    21
    Views
    19,888

    Carl, Most of the “Snipes” I’m referring to, are...

    Carl,
    Most of the “Snipes” I’m referring to, are “Hole Snipes” as in NAVY engineering folks��
    I appreciate all the help thus far! The hard part is behind me, now to dial this puppy in!!!
    Have a...
  18. Replies
    21
    Views
    19,888

    Okay,Just wanted to bring everyone up to speed on...

    Okay,Just wanted to bring everyone up to speed on what I have been doing to my ‘96 Trans Am LT1 0411 PCM conversion I’ve been Collaborating with Carl (“Intech”) to get my project working. Just so...
  19. Replies
    21
    Views
    19,888

    Dave, Do I have to change the file .ext in order...

    Dave,
    Do I have to change the file .ext in order to use these .bin files you posted?
    They download as .php files.....
    Thanks!
    Ben Smith
  20. Replies
    21
    Views
    19,888

    Carl, I’m new to this tuning thing (isn’t it...

    Carl,
    I’m new to this tuning thing (isn’t it obvious?��) sorry couldn't help myself! What exactly are you wanting me to post? Base file? What is that other than the .bin? Operating system?
    12212156...
  21. Replies
    21
    Views
    19,888

    Thank you all for checking into this for me! I am...

    Thank you all for checking into this for me! I am at work today, but once I get home, I’ll post what I have. No wonder this thing runs like crap.
    Thank You!
    Ben Smith
  22. Replies
    21
    Views
    19,888

    1996 LT1 to 12200411 PCM conversion help

    Hello everyone!
    as the thread states, I am in the middle of a 12200411 PCM conversion on my '96 Trans Am WS6 LT1, I have got the car to run, albeit very roughly, but running none the less. I used...
  23. Replies
    0
    Views
    1,625

    ‘96 LT1 to 12200411 PCM conversion

    Hello everyone!
    I know this has been brought up several times in the past, but I am trying to be clear on how
    to get my PCM programmed with the correct “Express Van L31 Tune” I just re-pinned my...
  24. Well, i’m gonna start with an express van tune...

    Well, i’m gonna start with an express van tune and go from there.
    I’ve looked for a stock 1996 LT4 .bin file, but haven’t found one yet.
    guess I’ll just wing it once i get all my hardware...
  25. Dave, What, if anything would this cost me to...

    Dave,
    What, if anything would this cost me to have done? My wife is already on me like
    “stains on a shirt” about all the money I have poured into my car, just trying Not to spend
    more than I have...
Results 1 to 25 of 41
Page 1 of 2 1 2