Bringing TBI and Multi Port Fuel Injection to a New Level.     EFI Conversions and Tuning! Seattle to Portland! E-mail Tuning Consultant!

Search:

Type: Posts; User: Terminal_Crazy

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    139
    Views
    6,059

    Yeah but you could recalc the checksum & update...

    Yeah but you could recalc the checksum & update that byte.


    Steveo's EEHack does to a small extent


    Great, will that be ready by tea time? :-)

    I wish I knew more about these sytems, so I...
  2. Replies
    139
    Views
    6,059

    Do the flash roms HAVE to be fully zero'd and...

    Do the flash roms HAVE to be fully zero'd and 0xFF set first ?
    I always thought it was a bit crap that you couldn't just flash individual cells & update them.

    Mitch
  3. Replies
    6
    Views
    746

    Excellent. Thankyou. Lots more reading up Now. ...

    Excellent. Thankyou. Lots more reading up Now.

    Thanks
    Mitch
  4. Replies
    6
    Views
    746

    Thanks, It's a 2001 A4 LS1. From what I can...

    Thanks,

    It's a 2001 A4 LS1. From what I can gather( Some conflicting overlapping info on dates) it should be a P01 9354896 512Kb.

    P01 2001-2002 C5 | 1999-2001 Camaro/Firebird/Corvette...
  5. Replies
    6
    Views
    746

    Cheers Steveo, looking into these now. Thanks...

    Cheers Steveo, looking into these now.

    Thanks
    Mitch
  6. Replies
    6
    Views
    746

    OBD2 Tuning - Starter

    Hi guys,
    What's the current state of OBD2 tuning, logging & flashing software.
    I've only tunes LT1's upto now.

    I've been asked if I can tune a C5 Auto Corvette, not sure what year yet. I...
  7. Replies
    8
    Views
    531

    Thanks for the replies guys. I'll finish my...

    Thanks for the replies guys.

    I'll finish my upgrades and see where I am later, after this epidemic has died down and we're allowed back out.

    Thanks
    Mitch
  8. Replies
    8
    Views
    531

    I was just after confirmation that the PCM was...

    I was just after confirmation that the PCM was capable of more than 6400 rpm.

    I had been looking at the MSD digital 6a, but more for the 2 step launch & Timing retard built in.
    Kur4o: Could those...
  9. Replies
    8
    Views
    531

    OK. The XDF shows it as 6375 Would it be better...

    OK. The XDF shows it as 6375
    Would it be better set back to $E6 rather than $FF>


    Not really sure, it just seems to sit there. It doesn't sound or feel like it's missing, it just doesn't rev any...
  10. Replies
    8
    Views
    531

    LT1 Hard RPM Limit

    I see in Kur4o's LT1 XDF the usual Fuel Cut Offs:
    Speed:26DC & resume 26D7
    RPM: 26D8 & resume 26DD

    I can also see
    167B4: Max RPM for 0 bpw
    167BA: " " " " " " " must be...
  11. Try swapping your Test Leads over and test again!...

    Try swapping your Test Leads over and test again!

    Mitch
  12. Replies
    17
    Views
    2,018

    I have a '95 F body and haven't had any issues...

    I have a '95 F body and haven't had any issues bleeding the brakes.

    I've used a vacuum unit that you fit onto each brake nipple & pull the fluid through.
    I generally do it the old fashioned way,...
  13. Replies
    17
    Views
    2,018

    Hi I guess you have all those data streams. ...

    Hi
    I guess you have all those data streams.
    That's what I had long before I read anything about anyone talking to the PCM. I think TunerCats was it at the time.
    I was only looking to access the...
  14. Replies
    663
    Views
    122,061

    Just been reading p40 on the coolant temperature...

    Just been reading p40 on the coolant temperature sensor. That's interesting. I've not seen seen a sensor used with dual range/sensitivity before.
    Presumably there must be some bit in the PCM that...
  15. Replies
    17
    Views
    2,018

    The message streams are floating around the 'Net....

    The message streams are floating around the 'Net.
    I have them saved away.

    I also acquired a GM factory 1993 F Body ABS suppliment which has lots of info.It also mentions the Tech 1 and 6 test...
  16. Replies
    17
    Views
    2,018

    Hi Gary Dougs excellent 9495Scan software can...

    Hi
    Gary Dougs excellent 9495Scan software can communicate & control ABS on 94-95 F bodies as well as other engine controls (fans etc.)

    I wrote software to communicate with the ABS and SIR system...
  17. Replies
    663
    Views
    122,061

    That's interesting because that's bang on where...

    That's interesting because that's bang on where my O2's decide to flat line between 45 to 50 degrees C.

    Mitch
  18. Replies
    39
    Views
    2,768

    Sensors were new. cables tested ok. Knock circuit...

    Sensors were new. cables tested ok. Knock circuit tested ok many times.
    The cables were occasionally rubbing on the frame causing a short.

    HTH
    Mitch
  19. Replies
    39
    Views
    2,768

    Hiya I've had the ERR43 & MALF43A codes on my...

    Hiya
    I've had the ERR43 & MALF43A codes on my '95 Z28 occur when the headers melted the knock sensor cables.
    Very intermittant and hard to diagnose as cables all test OK.

    HTH
    Mitch
  20. Replies
    154
    Views
    16,928

    Evening Stevo Just downloaded v4.84 On the...

    Evening Stevo

    Just downloaded v4.84
    On the front page it shows v4.80 (Pre-release)

    Also, I guess it's a QT issue, Is it possible to be able to Copy & Paste data from the Analyzer tables as I...
  21. Replies
    173
    Views
    17,701

    Yes I've posted this previously a good while...

    Yes I've posted this previously a good while back.
    Consistantly around 44C to 56C the RHS O2 flatlines.
    The AFR gauge also leans out and car runs noticably rougher.
    This is still in OL as I don't...
  22. Replies
    173
    Views
    17,701

    Hiya How did you calculate those Open throttle...

    Hiya
    How did you calculate those Open throttle figues?
    Closed throttle seems relatively straight forward.

    Is there any easy way to display these in TunerPro in an easier to view format?
    as in...
  23. Replies
    173
    Views
    17,701

    Hiya Car warmed up >86C I started to reset...

    Hiya
    Car warmed up >86C
    I started to reset BLM's after the first few, so went round the table again at the end.
    I basically logged until the BLM's settled (about 1000 logs minimum between changes)...
  24. Replies
    173
    Views
    17,701

    Similar results to me then, extending the time...

    Similar results to me then, extending the time the fuel sits in the port or forcing it further down the port so it has less chance of being sucked back out?

    Have you tried a sweep test.
    This was...
  25. Replies
    154
    Views
    16,928

    Appologies for being away for a while. Just...

    Appologies for being away for a while.
    Just spent a small fortune on a Thermal Spray system so I'm now able to spray Thermal Barrier Ceramic coatings.

    Laptop screen cracked a few weeks ago & now...
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4