For the moment, I got a $88 bin running well, and a $A1 bin running also.
I noticed some differences between them...
Before I start logging, I want to choose the most optimal out of the 2, and...
Type: Posts; User: D Max
For the moment, I got a $88 bin running well, and a $A1 bin running also.
I noticed some differences between them...
Before I start logging, I want to choose the most optimal out of the 2, and...
The code 42 is been solved for now, seems like another bin is working....
Now facing a next problem.....
Did a little test drive today.
my speedometer moves, but showed 5 mph at about 50 mph
In...
discovered today that the BFAU bin works also... at least I have a base to work with..
Advance works with this bin, and no SES light. Engine runs OK
Only the tach does not work at the moment, but...
Now it is getting weird.....
today I put in the original AZTY bin that works with the distributor....
It runs (ok, it surges a lot...)
but no code 42, no SES light, nothing....
with a...
bought myself a third ICM today.
Connected it => same problem
Seems not logic that 3 ICM's have the same problem, and nobody seems to have had the same issue.....
tested the tach with a pulse...
for the moment, i came to the following conclusions:
the ECM gets a reference signal from the ICM (=> fuel injection works + tach signal in Tunerpro)
The 4 wires between the ICM and the ECM have...
Did some troubleshooting today......
This is what i all did:
checked all the connections, and they are like they should be on the wiring diagram above...
Measured the bypass wire between the...
Today I checked my connections once more, because i get code 42
First i thought it was because I disconnected the est bypass, to check if the base timing was zero.
So I disconnect the power some...
@ Robert
Get the engine running with the DIS yesterday.
Runs pretty good, as I just used a 3.1 VE table...
I just have no tach...
I connected the white tach wire to the pin C of the 6pin...
Today, I got the ignition working.
The engine runs quite good, but the ECM throws the code 42...
I also have no tach.
I do have a tach signal in tunerpro....
Still work in progress..
grtz,...
I looked at the engine block, and the bunch of wires that came with the block, and indeed, it makes a lot more sense.....
This sensor has only 2 wires, and they have the same color....
Did not...
I guess it will come down to the cps connections then....
It could be 7x, i did not take off the harmonic balancer to count it.
The connector of the CPS has 3 wires.
As I found on the...
Today, I installed the DIS.
I used this wiring diagram:12174
I used the pickup coil, original on the 3.4 engine.
I get no spark.
Someone that can give me a 'golden' tip?
grtz, D
Thanks..
Will the A1 work with the 700R4 transmission?
and maybe a stupid question, but offset 60°.... will that mean that if I switch the spark plug wires, i don't need to change a thing?
...
Hello
Since I build in a 3.4 V6 in my 1990 Firebird, I'm thinking for using the DIS that came with that engine.
The engine runs great now, but has not enough power in the high Revs.
Found some...
@ Robert...
You mentioned before that you switched to $A1
I believe that is to use the DIS-system correct?
Could you tell me what cables I have to reconnect/change to use the DIS?
grtz, D
Hello
Got the fuel ok by now bit by bit...
First the low throttle, now started to the higher throttle...
Almost all the BLM's between 126 and 130....
Noticed that when I go full throttle, the...
hello
maybe I was a little bit too fast with my prevoius questions ...
Done a lot of reading here on the forum and elsewhere on the internet, and I think I am a step further now....
For the...
Hello
Is there someone who can set me on the right track.....
I was expecting to simply find a table map/RPM/injector time and TPS/RPM/injector time, like on a lot of other programs I worked...
Hello
problem is actually that I cannot find the injector pulse tables at first sight in the XDF file I have.......
can I assume that all the bin files for the different engines that use the...
Hello
Mask problem is solved.... Was a bit stupid thow....
Was no present in the XDF, but I heard it was the 9th byte
Got the value of 141 for the mask, so I thought I had to look in another...
is it possible I cannot disable checksum in the $88 mask?
grtz, D
Today I tried a different laptop => same result
If I have the time, I try tomorrow to connect it to another car (same year/type/model)
Anyone who have some other suggestions to detect what the...
Hello
I used all the files from gearhead...
And a couple of other files....
today, I even tried 3 differend ecm's, just to be sure the problem was not the ecm...
Problem stays the same...
...
Hello
Been new to this forum, so pleas forgive my possibly stupid questions....
Some time ago, I changed my 3.1 v6 engine for a 3.4 (I know, is not a V8)
Sticked with the v6, because over...