Search:

Type: Posts; User: ltxdave

Search: Search took 0.01 seconds.

  1. Replies
    9
    Views
    15,704

    Well, it does appear to have been some hidden...

    Well, it does appear to have been some hidden parameter. I modified the 6speed bin to match my auto program and flashed it last night. No more problem at coast down! Thank you guys for the...
  2. Replies
    9
    Views
    15,704

    I will have to look tonight. It's possible that...

    I will have to look tonight. It's possible that it goes through the BCM, but I would think it would be the same as the fbody and b bodies.
  3. Replies
    9
    Views
    15,704

    The time between pulses value is 499.98 ms. This...

    The time between pulses value is 499.98 ms. This is the same as my 96 Corvette that used the same sensor/transmission.

    I started with my stock y-body automatic BIN file and modified it to the...
  4. Replies
    9
    Views
    15,704

    Coast Down Drivability Issue-1995 LT1

    I'm having a hard time figuring out how to address this strange driveability issue with my 95 LT1 Corvette. When I coast down to a stop in gear with my foot off the gas, the car will almost stall...
  5. Replies
    2
    Views
    3,031

    That is what I'm trying to improve is part...

    That is what I'm trying to improve is part throttle drivability. My thought was to increase the opening of the IAC to help distribute air more evenly at lower RPM. By reading the descriptors on...
  6. Replies
    2
    Views
    3,031

    What is Normal IAC Behavior?

    Looking at my datalogs and the ee definition file, I'm trying to determine if what I'm seeing is normal or not. The IAC counts are much higher than the park position with the additional counts from...
  7. Replies
    11
    Views
    8,129

    I noticed last night that under stay cruise, it...

    I noticed last night that under stay cruise, it basically has about 11" of vacuum until it reaches about 2000 rpm, then it jumps up to about 15". The only way it gets over that is under closed...
  8. Replies
    11
    Views
    8,129

    Well, the map reading has been confirmed with the...

    Well, the map reading has been confirmed with the mechanical gage. I datalogged a bit tonight in speed density mode and will load revisions tomorrow night and see where everything is.
  9. Replies
    11
    Views
    8,129

    Yes, that is how I got to 65 from about 70. I am...

    Yes, that is how I got to 65 from about 70. I am going to check my map sensor vs a mechanical gage tonight. I will look again for vacuum leaks as well. I don't have any starter fluid, but I will...
  10. Replies
    11
    Views
    8,129

    About 10.8:1. I have been trying to tune for...

    About 10.8:1. I have been trying to tune for several weeks. These results are with added timing at idle and stock MAF tables.
  11. Replies
    11
    Views
    8,129

    11804 Cam card. I have no vacuum leaks that...

    11804

    Cam card.

    I have no vacuum leaks that I can find. Everything is fresh with only break in miles on it so far.
  12. Replies
    11
    Views
    8,129

    EEHack Cylinder Balance Test

    I recently downloaded eehack and was playing around with the cylinder disable feature and cylinder strength test. When I manually disable cylinders 1-4, the result is very noticeable. 5-6 not do...
  13. Replies
    1
    Views
    3,077

    OK, I found data for the Bosch IIIs, but I'm...

    OK, I found data for the Bosch IIIs, but I'm confused by some of the data. The flow rate data lists references 0,5,10,.....80 Is this data PSI or kPA? The flowrate listed ranges from about 40 to...
  14. Replies
    1
    Views
    3,077

    Need Injector Data for 36 lb Bosch III's

    I have a set of 0 280 155 868 bosch IIIs and I'm looking for the injector data to use in Tunercat for my 95 LT1 Corvette. Any help is greatly appreciated!!
  15. Replies
    0
    Views
    1,898

    New Guy From NW Florida

    I'm new, from Marianna, FL. I'm a mechanical engineer and have rebuilt/modified cars since I was 12. I have recently started tuning with Tunercat and found this forum trying to find data for my 36...
Results 1 to 15 of 15