Search:

Type: Posts; User: whatif3387

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    4,973

    I can take a good look when I get home as I...

    I can take a good look when I get home as I havn't been wrenching on or driving the truck in well over a year since moving but from what I remember my VRFPR is in line before the the TBI unit and has...
  2. Replies
    8
    Views
    4,973

    I run a L31 with a sbc bored out TBI and BBC 454...

    I run a L31 with a sbc bored out TBI and BBC 454 80lb injectors. After months of trying to tune around the large injectors at idle I gave up and bought a aeromotive VRFPR. I just could't control the...
  3. Replies
    6
    Views
    6,078

    I had a similar problem where I would randomly...

    I had a similar problem where I would randomly lose spark and no power to injectors. This began shortly after installing a new distributor with new ignition control module that was included with the...
  4. Replies
    22
    Views
    15,611

    I had an issue just like this no fuel or spark...

    I had an issue just like this no fuel or spark while cranking and it ended up being the ICM. I had replaced the ICM when I installed a new distributor just so that everything was new and the pins in...
  5. Replies
    76
    Views
    51,178

    I run a AC delco TPI pump in my 95 c1500 tbi...

    I run a AC delco TPI pump in my 95 c1500 tbi truck. It was a direct swap for me it works great but it did over power the spring in the stock regulator I had to try out a few different springs. I...
  6. Thread: esc

    by whatif3387
    Replies
    12
    Views
    9,977

    I'm glad I posted on this thread because I just...

    I'm glad I posted on this thread because I just learned the solution to a problem i've been chasing for over 2 years. My truck is a 95 that I swapped added a 96-00 L31 to which I'm controlling with...
  7. Thread: esc

    by whatif3387
    Replies
    12
    Views
    9,977

    My truck is a 1995 with the 7427 and yes the ESC...

    My truck is a 1995 with the 7427 and yes the ESC is built in.
  8. Replies
    10
    Views
    10,803

    Yes everything is on the same chip engine and...

    Yes everything is on the same chip engine and trans. Once you setup the bluecat program and it generates the tables they're laid out the same as far the columns and rows resolution. The thread I...
  9. Replies
    10
    Views
    10,803

    Actually I believe it was you fast355. I spent a...

    Actually I believe it was you fast355. I spent a good deal of time searching the forums for 4l60e trans tuning information and couldn't find very much. But I did find an older thread here mentioning...
  10. Replies
    10
    Views
    10,803

    I'm not sure if your just curious about the bins...

    I'm not sure if your just curious about the bins you mentioned being compatible or not or your actually interested in tuning the shift points for the different gear ratio. I recently started spending...
  11. Replies
    110
    Views
    80,936

    This is exactly what I'm running except with TBI....

    This is exactly what I'm running except with TBI. I'm running the EBL piggy backed with my original 7427 to control my 4l60e and it works great. Bob from dynamicefi was able to provide me with a very...
  12. Replies
    110
    Views
    80,936

    I've only read through part of this thread i'm...

    I've only read through part of this thread i'm not sure if this has been mentioned or not but I'm pretty sure an EBL from dynamicefi will do what your trying to do for rather cheap. Not as cheap as...
  13. Replies
    5
    Views
    6,367

    That is very helpful thank you I'll give that...

    That is very helpful thank you I'll give that stuff a look this week.
  14. Replies
    5
    Views
    6,367

    Sorry I guess I should of mentioned it in my post...

    Sorry I guess I should of mentioned it in my post I need to make a signature. It's a 1995 c1500 I swapped my old 5.7 tbi engine for a new GM vortec L31 5.7. I'm running the GMPP TBI vortec intake...
  15. Replies
    5
    Views
    6,367

    Idle PW and VAFPR

    Can anyone offer me any incite on what an acceptable minimum pulse width would be. I'm currently at 15 psi with 80# injs. I just recently realized I don't have enough fuel pressure to achieve less...
  16. Replies
    0
    Views
    2,763

    Advice for chip burning.

    My current setup is as follows... L31 vortec with 1.6 RR, GMPP TBI intake, Bored TBI with 80lb inj at 15 psi and full exhaust. I'm tuning the motor myself using an EBL flash setup. What I need advice...
Results 1 to 16 of 16