Search:

Type: Posts; User: MAC

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    948

    Only one bin on the file. Not stacked. I selected...

    Only one bin on the file. Not stacked. I selected the 27sf512 chip in the drop down menu from TunerPro, which has always been ok for me in the past.

    Any ideas on why that bin file I read off looks...
  2. Replies
    1
    Views
    1,185

    Looks like 20 degrees of advance in the idle...

    Looks like 20 degrees of advance in the idle range of 400 - 1200 RPM and less than .32 cylinder airmass. This is not dangerous, should be fine. Probably a little on the low side in my experience. You...
  3. Replies
    3
    Views
    948

    305 to 350 Swap - AWFY to AUJP - 7730 ECM

    Can someone validate my thinking here or point out the problem? I burned AUJP onto a sst 27sf512 chip, installed the chip on a G1 and started the car. It runs like garbage. Idles at 2000 rpm, stalls...
  4. Replies
    8
    Views
    3,286

    This will work for me. Thanks ����

    This will work for me. Thanks ����
  5. Replies
    14
    Views
    2,254

    Thanks Dave. What is the use of the PCB you...

    Thanks Dave. What is the use of the PCB you attached to that last post?
  6. Replies
    14
    Views
    2,254

    I just learned the same thing - the G1 is...

    I just learned the same thing - the G1 is discontinued - and posted this in another thread. Anyone know details on why?
  7. Replies
    8
    Views
    3,286

    Moates G1 Adapter Discontinued?

    The Moates G1 adapter has been discontinued and will not be replaced. Does anyone have any insight as to why? I fear that every gearhead's favorite 3-letter federal government agency is involved.
    ...
  8. Replies
    86
    Views
    234,702

    Post the BIN that you are currently running.

    Post the BIN that you are currently running.
  9. Replies
    86
    Views
    234,702

    Something is off, most likely in the way you...

    Something is off, most likely in the way you copied and pasted. The ignition timing should generally be 15-40 degrees at any given point in the table.
  10. Replies
    1
    Views
    2,255

    What Mask for 1995 TBI V6? PCM is 16199995 BJWS

    Subject pretty much says it all. Anyone have any tips or ever tune this computer or the TPI 4.3 V6?

    Thanks,

    AC
  11. It all depends on your expectations. If you plan...

    It all depends on your expectations. If you plan to spend hours and hours of troubleshooting, testing, data logging, and tuning then yea, should be fine. If you are looking for something that works...
  12. I am not personally familiar with this cam. I can...

    I am not personally familiar with this cam. I can tell you that I am using the sealed power CS-1014R cam which I am happy with. However my setup probably a lot different than yours. Specifically I am...
  13. Replies
    18
    Views
    13,101

    Looks like it. Gonna see if I can find it...

    Looks like it. Gonna see if I can find it somewhere else. Sry about that.
  14. Replies
    7
    Views
    6,835

    Check out my post #4 above. My BIN is set to 21.4...

    Check out my post #4 above. My BIN is set to 21.4 Kpa. Data logs have a delta less than 2 when the AE comes on.

    Also - love me some parameter finder!
  15. Replies
    7
    Views
    6,835

    Thanks troutdog. Are you running E6? What steps...

    Thanks troutdog. Are you running E6? What steps did you take to prevent open loop ldle?
  16. Replies
    7
    Views
    6,835

    I looked at that. Title: MAP Difference to...

    I looked at that.

    Title: MAP Difference to Enable AE at Idle
    Location: 48AF

    Set to 21.4 Kpa in my BIN. I found numerous examples in the datalog where the MAP difference is less than 2 Kpa and...
  17. Replies
    7
    Views
    6,835

    Datalog attached for anyone who is interested.

    Datalog attached for anyone who is interested.
  18. Replies
    7
    Views
    6,835

    Pros and Cons of Open Loop Idle on E6

    I have been chasing a closed loop idle problem. Closed loop idle works great except for a little stumble every ~5 seconds. It is related to AE but I am not sure if it is being caused by AE....
  19. Is this the cam? ...

    Is this the cam?

    http://www.lunatipower.com/Product.aspx?id=2325

    It doesn't say but based on the price it's a flat tapper cam right? How does it behave in a 4WD truck? Seems like 2400 is way...
  20. This is very encouraging. I'm not familiar with...

    This is very encouraging. I'm not familiar with that cam but I'll check it out. Now I'm torn between the seemingly easy install of shorties and the Jegs Y pipe or just going all out and trying to...
  21. Thanks for that tip Dzida.

    Thanks for that tip Dzida.
  22. Any updates or recommendations on the header fit?...

    Any updates or recommendations on the header fit? Would you go the same route if you were going to do it again?
  23. Thread: New Member

    by MAC
    Replies
    1
    Views
    2,752

    Welcome aboard. I have found lots of good help...

    Welcome aboard. I have found lots of good help here. That said, if you are like me (dumb and stubborn) you will also spend many many hours reading and researching to learn more. Do not mean to...
  24. How do they fit? Did you have to "massage"...

    How do they fit? Did you have to "massage" anything?
  25. Header fitment with 1993 K1500 - Recommendations Please

    Hey everyone,

    Does anyone have first hand experience with fitting headers onto a 1993 K1500? If anyone can recommend a specific brand and model/part number of something known to fit well I would...
Results 1 to 25 of 88
Page 1 of 4 1 2 3 4