obd wiz is the software that obd link sx cables uses.i have not yet had the chance to connect to a vehicle yet but the program seems like it gives a lot of info for logs.similar to some hand held...
Type: Posts; User: S.O.B.B.
obd wiz is the software that obd link sx cables uses.i have not yet had the chance to connect to a vehicle yet but the program seems like it gives a lot of info for logs.similar to some hand held...
On my drive to work the engine cut out.no restart. Notice no check engine light. Check fuses and Ecm B fuse burnt.had a pack of 6 10 amp fuses.the rest of my drive to work it blew 10 more fuses. Last...
I am a licensed brake tech with abs experience but have been out of the biz more than 20 years.I've tried to stay familiar with systems and such. I am unfamiliar with the exact system u have but had...
Thanks for that info.didn't know that the cable was not so expensive. But searched and found that the gq4x4 does have byte swap.I may try it this way just to see how difficult the soldering is.but...
Thanks.I guess I should have been a little more specific.if I remove the chip and use an adp-019 (psop44 to dip32) to read it in my GQ4x4.then use the tunerpro xdf to make changes and reflash the...
Did anyone ever have any luck burning/reading/flashing the chips from ls pcm using tuner pro xdf/adx files.I'm asking because I didn't see a cheap cable for doing this.picked up a 0411pcm...
Cel should come on off then back on if the key is in the run position until u crank .is the bulb working.sounds like possible different pin outs from one set up to the other what are the service...
Thanks for the reply.just what I needed to know. I do have the oe ecm but at this time I guess I'll rebuild the dizzy that's in it. The speeduino sounds interesting but maybe above my computer...
Good day all.maybe someone can answer this.I have a distributor from a 92 4.9L Deville engine.ordered parts to rebuild. Realized after that the star wheel for the pickup on this has a missing tooth...
Couple questions about using a larger throttle body.
1st when using a larger tb on an otherwise stock engine would there be any places in the ve table (idle or open) that would be lower than stock...
14392
14391
143901438914388
This is 92 Cadillac 4.9 engine with a dodge 2 inch throttle body 700r4 behind it in a 3600lb s15.
7427 mpfi
Haven't been able to post much.finally got the time to fix exhaust manifold leak.it cracked beside my weld.been trying to get things right on this a while now.my break switch being loose was...
I didn't reread that but I believe you are correct.it's been a while since I looked at any of that.after the 7427 swap I just left it as stock.mostly because I could not find any of those settings...
I'm sorry I don't have a link.I can't figure out how to do that.so I took a screen shot.hope u can find the same write up.the latency part is quite a ways into it.14305
R Bob has a good right up on TGO about latency and the amount of advance added along with how to test what u've got.its time consuming.I can't remember but I think 3 or 4 different latency setting...
Finally just got around to installing some new parts.new acdelco 4 wire heated o2.new knock sensor.new aem wideband o2 wired to read in tunerpro.I can say this.in 10 logs I've gotten a lot closer to...
If u put grease like bearing lube etc on the gasket surfaces both sides it makes seeing the leak easy if it won't seal.it sometimes leaves the gasket in non reusable state if paper surfaces peel.but...
One would think if u have a intake leak to the crank case it would suck oil in.if u disconnect vacuum and breather for pcv u shouldn't still have tons of vacuum at the pcv hole or oil fill cap hole.u...
I had considered thinning my harness after engine swap and was glad I didn't remove wires after because they can be used for other functions.I use the power wire from the evrv egr plug for my heated...
13811sorry about the blury pic but there are those settings and under iac there are settings for how many counts the opening is.that's how much air it's letting in to idle at desired rpm.there are...
If u want it functional and the parts are functional it is that simple to swap connectors or if u don't want it to function you can disable it in tp. There is a pat h u can apply to disable it in...
The 3 wire egr plug is for evrv.2 wire egr plug is egr solenoid.
Pin A4 says egr.grey wire.
The 3 wire for evrv is the same 2 wires as in the 2 wire egr solenoid plug.the 3rd wire is a ground.hth...
http://www.gearhead-efi.com/Fuel-Injection/showthread.php?2203-1227747-VSS-wiring-question
Hope that's how a link is posted.
If ur using 7747 there is a post under 1227747 wiring question.I think it may have the info u seek.I searched drac wire diagram and the second last on the list is that post.hth
If a 3 cable set up is what u will use I'd grind the weld off and replace it with the arm off a tbi and make a single bracket that holds all 3.if no cruise control will be used I'd use the stock arm...