Only one bin on the file. Not stacked. I selected the 27sf512 chip in the drop down menu from TunerPro, which has always been ok for me in the past.
Any ideas on why that bin file I read off looks...
Type: Posts; User: MAC
Only one bin on the file. Not stacked. I selected the 27sf512 chip in the drop down menu from TunerPro, which has always been ok for me in the past.
Any ideas on why that bin file I read off looks...
Looks like 20 degrees of advance in the idle range of 400 - 1200 RPM and less than .32 cylinder airmass. This is not dangerous, should be fine. Probably a little on the low side in my experience. You...
Can someone validate my thinking here or point out the problem? I burned AUJP onto a sst 27sf512 chip, installed the chip on a G1 and started the car. It runs like garbage. Idles at 2000 rpm, stalls...
This will work for me. Thanks
Thanks Dave. What is the use of the PCB you attached to that last post?
I just learned the same thing - the G1 is discontinued - and posted this in another thread. Anyone know details on why?
The Moates G1 adapter has been discontinued and will not be replaced. Does anyone have any insight as to why? I fear that every gearhead's favorite 3-letter federal government agency is involved.
...
Post the BIN that you are currently running.
Something is off, most likely in the way you copied and pasted. The ignition timing should generally be 15-40 degrees at any given point in the table.
Subject pretty much says it all. Anyone have any tips or ever tune this computer or the TPI 4.3 V6?
Thanks,
AC
It all depends on your expectations. If you plan to spend hours and hours of troubleshooting, testing, data logging, and tuning then yea, should be fine. If you are looking for something that works...
I am not personally familiar with this cam. I can tell you that I am using the sealed power CS-1014R cam which I am happy with. However my setup probably a lot different than yours. Specifically I am...
Looks like it. Gonna see if I can find it somewhere else. Sry about that.
Check out my post #4 above. My BIN is set to 21.4 Kpa. Data logs have a delta less than 2 when the AE comes on.
Also - love me some parameter finder!
Thanks troutdog. Are you running E6? What steps did you take to prevent open loop ldle?
I looked at that.
Title: MAP Difference to Enable AE at Idle
Location: 48AF
Set to 21.4 Kpa in my BIN. I found numerous examples in the datalog where the MAP difference is less than 2 Kpa and...
Datalog attached for anyone who is interested.
I have been chasing a closed loop idle problem. Closed loop idle works great except for a little stumble every ~5 seconds. It is related to AE but I am not sure if it is being caused by AE....
Is this the cam?
http://www.lunatipower.com/Product.aspx?id=2325
It doesn't say but based on the price it's a flat tapper cam right? How does it behave in a 4WD truck? Seems like 2400 is way...
This is very encouraging. I'm not familiar with that cam but I'll check it out. Now I'm torn between the seemingly easy install of shorties and the Jegs Y pipe or just going all out and trying to...
Thanks for that tip Dzida.
Any updates or recommendations on the header fit? Would you go the same route if you were going to do it again?
Welcome aboard. I have found lots of good help here. That said, if you are like me (dumb and stubborn) you will also spend many many hours reading and researching to learn more. Do not mean to...
How do they fit? Did you have to "massage" anything?
Hey everyone,
Does anyone have first hand experience with fitting headers onto a 1993 K1500? If anyone can recommend a specific brand and model/part number of something known to fit well I would...