Search:

Type: Posts; User: X-man

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    1,434

    Another Thank you

    I would like to take time to thank David for all his work on my 94 454 Vortec project. Everything from gathering parts, to custom ecm work and harness adapters, to troubleshooting and tuning. His...
  2. Replies
    15
    Views
    4,066

    The best person to speak with on that would be...

    The best person to speak with on that would be David at Old School EFI. He is a wealth of knowledge on that kind of info. I know when I started this process he sent me an email on the process I...
  3. Replies
    15
    Views
    4,066

    Not sure which part of the conversion you are...

    Not sure which part of the conversion you are asking about but the mechanical was an L29 top end with Fast 36lb injectors and an L19 distributor. Fuel lines were custom. The ecm started as the...
  4. Replies
    15
    Views
    4,066

    Best I can figure is something in the 7427 ecm...

    Best I can figure is something in the 7427 ecm was not happy being converted to run the multiport setup. I bought an extra set of injectors and a brand new distributor to see if that made any...
  5. Replies
    15
    Views
    4,066

    94 K3500 454 Vortec

    I wanted to take a moment to post my experience with the Flash II with port mod. I have a 94 K3500 that came from the factory with tbi, 5 speed, and 4.56 gears front and rear. The performance and...
  6. Thanks.

    Thanks.
  7. Anyone have any files for a 7727 TPI with a ZZ4 crate engine

    I have a guy who has asked me to help him sort out a 90 Corvette with a ZZ4 crate engine installed in it. The car has the factory prom in it with an Edelbrock TPI high flow runners and a Holley...
  8. Replies
    5
    Views
    8,734

    I run a chassis dyno on the side and have alot...

    I run a chassis dyno on the side and have alot more interest generated towards stuff that the EFI Live or HP Tuners will do and there is an increasing market for I just have to get more comfortable...
  9. Replies
    0
    Views
    2,683

    OBD II option deletion questions?

    I'm sure this has been gone over and I'm overlooking this in the search menu but I recently got my Jet 14005 program to communicate with my 97 S10 L35 truck. I read the stock calibration and noticed...
  10. Replies
    5
    Views
    8,734

    I just loaded the program to my old laptop from...

    I just loaded the program to my old laptop from the dyno and it has serial ports. What is a better tuning solution for the stuff HPTuners and EFILive won't do?
  11. Replies
    5
    Views
    8,734

    Jet 14005 connection help

    I have a 97 S10 with an L35 4.3 liter and a 5 speed. I wanted to get into the ECM and turn off with rear O2 sensor and the EGR valve. I also have been toying with the idea of installing a bigger...
  12. Replies
    16
    Views
    19,953

    With Tom's help I went to the section where the...

    With Tom's help I went to the section where the BINs were listed for my BHDC code and downloaded that and burnt that to a chip and the truck started right up with no SES light and ran fine. Tom had...
  13. Replies
    16
    Views
    19,953

    I never did get it to run without the SES light...

    I never did get it to run without the SES light on. I have been using my stock calibration file that I took off the stock chip and saved to my computer. I modify than reflash that to a new chip. I...
  14. Replies
    16
    Views
    19,953

    I did go back and look at my file again and did...

    I did go back and look at my file again and did the comparison again with the $OE mask. I found a couple of things that were different as far as the scaler settings go. The biggest difference was the...
  15. Replies
    16
    Views
    19,953

    stock bin file from my dually.

    stock bin file from my dually.
  16. Replies
    16
    Views
    19,953

    BHDC 4624 BC ad the ecm# is 16197427

    BHDC 4624 BC ad the ecm# is 16197427
  17. Replies
    16
    Views
    19,953

    I used the HDR to get the original calibration...

    I used the HDR to get the original calibration off my original memcal and saved it to the computer. I then opened it in TunerPro to look at it and the xdf file I got off the TunerPro website was the...
  18. Replies
    16
    Views
    19,953

    I have been installing the chip in the G1...

    I have been installing the chip in the G1 opposite the way it goes in the Burn 2. I thought that is what it said to do in the video I watched on youtube. This would be with the notch away from the...
  19. Replies
    16
    Views
    19,953

    Yes Sir I believe that was yours. I did the...

    Yes Sir I believe that was yours. I did the compare file and went down one by one through the scalers and the flags and matched everything but the tranny stuff. I noticed you left the single pass egr...
  20. Replies
    16
    Views
    19,953

    94 TBI 454 egr delete on a 7427 ecm

    I am new to factory ecm tuning and have a 94 Chevy dually with a TBI 454 with a 7427 ecm. I get the code 32 for the egr occasionally when driving the truck. It has a modified exhaust system and a...
  21. Replies
    0
    Views
    2,780

    Timing drifting at higher rpm

    I have been helping a guy tune a Fiero that has a 3.1 with an upgraded camshaft and has been turboed. It is running the code 59 software and has been converted to a newer ecm and DIS. We were...
Results 1 to 21 of 21