the site won't allow csv uploads. hmmm?
hopefully you can pull what you need from the log and other defs.
Ron
Type: Posts; User: f85gtron
the site won't allow csv uploads. hmmm?
hopefully you can pull what you need from the log and other defs.
Ron
Hi Dave,
Here's the $A1 files and a log too, in order to see how the idle works. $A1 seems to use both speed density and alpa-N both, blended at some point, but I can't figure out where. My...
Hi Dave,
$A1 is the code mask I'm working with.
Ron
I cannot figure out how to create idle blm history tables! Ultimately, I'd like to only use data when idle timer is activated and using idle ve table. is that possible? I can't figure out how to...
I noticed $88 launch control activates, but for partial throttle take-off, but I'd like to set it up for full pedal take-off, kind of like two-step, but mine is n/a. I've set the retard at like...
thanks robert!
i had them set to 0*. i thought it would pull 0* timing out, not set to 0* on neg drpm! i found some 3.1 numbers from an auru bin and they work much better. ill play with it some...
update:
Ive got rdsc to work really well, with the exception of decel. it cuts so much timing that the motor pops. it keeps pulling down past idle rpm almost to stall. with rdsc turned off,...
I've acquired an 84 fiero and would like to read the aldl data. Apparently, 84s are different than the rest. Will a different ads work instead?Ecm 1226156
Pulse width is commanded, based off a calculation of variables from several different inputs. If the pw is getting smaller while you rev, it's going opposite. Pw commanded has no correlation with...
I hear a lot of vacuum leak?. Maybe it's the audio though. What happens when you rev it up?
nevermind. found it here. thanks again robert!http://www.gearhead-efi.com/Fuel-Injection/showthread.php?1928-16172693-16184164-16184737-16196397-PCM-Information-P66-V6
Thanks Robert,It's for an L32 motor. Is that still p66?
Does anyone have a $2e bin for a 93-95 camaro? I'm curious about the sa tables. I looked in the bin files, but couldn't find it.It's a 3.4
SOLUTION:
It was the suspected cranking pw vs coolant temp table. I reinstalled the 19# injectors and only changed the above mentioned table values to roughly 5 msec and VROOM! Cranked right up hot!...
Thanks to all who've helped. I think I've found the problem, although I haven't been home to try the solution.
Let me start by saying I'm an idiot :)
I offset the values in the cranking pw vs...
Your probably right.
However, I set the Multec scaler and tables back to where they where before this condition and everything is normal, so it's one of those items for sure. Now that I'm thinking...
7730 using $88 mask.
I've installed new injectors (Ford 302), changed bpw vs volts table and zeroed out bpw vs bpw table. I've also set the Multec fixing factor scaler to 0.
Starts fine, runs...
I've used that max232 ttl board with both 160 (various fiero ecms) and 8192 baud (7730) ecms. Also used it with tuner pro and aldldroid.
The chip comes mounted in a breakout board and all you...
Have you read this thread on the max232 chip? http://www.gearhead-efi.com/Fuel-Injection/showthread.php?719-Uber-easy-DIY-USB-ALDL-Cable&highlight=Max232
I originally made a two transistor cable,...
My vote is for tuner pro. It's free and does everything you'll need to do for now. Burning, reading, even emulating.
Wow! Thanks for the explanation! I've already got the Speedo working from the ecm. It's just not "perfect", and that's what I'm looking for.....or less I wouldn't have gotten into tuning, right ;) ...
If it helps, i made a buffer from the attached schematic. Could i simply add a pot to adjust something?
Welcome! The fiero is a great platform for swaps and is very accommodating. I've swapped in the 3.4 from a camaro, an F23 trans from a cavalier, and ran it with a 7730 ecm. Both very good choices,...
I'm tuning a 24000 vss to a fiero. I'm running 14" tires and have had to adjust the road speed constant in $88 to about 26000 to calibrate to actual road speed. No problem there.
The problem is:...
Ok. I'll watch it closely and check it against a timing gun. You guys are AWESOME!