Hey thanks for this!! -- awesome bit of information !!
Type: Posts; User: greggbruceauto
Hey thanks for this!! -- awesome bit of information !!
I have searched for an hour now and not found any posts of anyone who has done something like this.
Talking about the pcm, wiring and programming here. I have the engine, swap mounts and headers....
I guess I should check the trans position pid next time I get to scan the car to see if it actually shows "drive" and "neutral" at the appropriate times.....
thanks, I was looking for what I...
whatever is factory..... I don't see a parameter with tunerpro that asks for neutral or drive.....
not sure how to edit the xdf either.....
unless you are asking about "IAC target speed...
um the t56 gears are at least as thick and actually have more teeth, thus more tooth contact. compared to a m-20 or 21 or even a 22, they are more heavy duty..... the 4500's are cast iron, and have...
actually, if you lay the planets for both of those side by side, you will find that the 700/4l60 planets have physically bigger gears --- but the apply components for the 400/4l80 are bigger ----...
when I went to 4l60e school when I worked at the dealer, they said it uses engine rpm, and has a "window" for the time it takes to complete a shift from the time it commands the solenoid to change...
305 mild cam, headers, 89 tpi firebird, $6E --- thought I had it fixed in warmer weather, but now it's cold out. When cold, starts and idles fine, as warms up, then if put in gear. will stumble and...
if I remember correctly, this is close to what my stock bin was set, just a few rpm below the cut-off, but (LOL) it was at something like 10,500....
on the most recent bin I programmed, I set it to...
BLESS YOU !!! that was the explanation I was looking for..... !!!!
1227165 ecm, $6e mask, 89 firebird TPI
there are 4 tables in this bin
TCC unlock speed vs. %TPS (not in 4th)
TCC lock speed vs. % TPS (not in 4th)
TCC unlock speed vs. % TPS (in 4th)
TCC lock...
yes, there are 2 parameters for each, disable and enable.
I was just looking for people that have used these and what their experiences have been with them...
well, let's say the kid is driving it at the speed limiter say, 80 mph-- will that, if done for a long enough time, create an over lean situation that could hurt the engine?
same thing with the...
I am using 1227165 ecm with $6e mask (factory) with a modified chip for an 89 firebird 305 TPI.
I have found the parameters in TunerproRT for disable and enable fuel, for both mph and rpm.
I am...
yeah, I think I noticed that, every few seconds or so all the data would max/min out --- you can see it in graph mode....
I just hope it's not going to be the case from now on...
this car is...
sorry, it's a $6E, 1227165 89 F body TPI
:rockon:A BIG thank you to
:jfj::jfj::jfj::jfj:
for that link, I got it in the mail yesterday, and finally after figuring out the 12v cig lighter adapter on the cable has to be plugged in, and...
That's the direction I'm leaning towards now.....
yeah, asked him -- says he is waiting on parts
what is MAX 232 -- this is the first it has been brought up.... I thought you said 'FT232' -- how does that differ from RS232?
I posted the links at the beginning of the thread -- the aldl cable I...
ummmmm, don't see any serial DB9 plugs on that page....
and no, it doesn't have to be FTDI,
IT JUST HAS TO BE SOMETHING THAT WORKS
yep, already did that -- found that post a week or so ago....
Yes, the cig lighter has good power and ground, it will run my snap on scanner and get data from the car just fine.
yeah, windows recognizes the serial to usb 'bridge' it calls it. It changes com...
I guess my real dilemma :mad1: is whether or not to get another adapter
http://www.mouser.com/ProductDetail/FTDI/CHIPI-X10/?qs=m5ogiX/X43nzRp8XLQeQIA==
or...
so is that yes, or no?