Bringing TBI and Multi Port Fuel Injection to a New Level.     EFI Conversions and Tuning! Seattle to Portland! E-mail Tuning Consultant!

Search:

Type: Posts; User: stew86MCSS396

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Didn't peak at this ^^^bin but the previous one...

    Didn't peak at this ^^^bin but the previous one target AFR was set at 14.1:1, would that be cause for lower than 128 BLMs??? Sorta read that's something you would do for E10 tuning.

    Yeah...I...
  2. Didn't know those existed. Got a part number for...

    Didn't know those existed. Got a part number for those and perhaps a link to where I might be able to acquire some. thanx!
  3. Replies
    13
    Views
    362

    Soooo...with that said are you using the correct...

    Soooo...with that said are you using the correct '7427 adx for your datalog???
  4. Another thing I noticed, how did you arrive at a...

    Another thing I noticed, how did you arrive at a 98#/hr injector. In my tunes, I've been trying to match the injector size to as close to what is actually installed w Dave W saying you can err a few...
  5. Seem to recall one of the master tuners here...

    Seem to recall one of the master tuners here saying knock will manifest itself on the datalog due to something that's happening before it gets reported so with that said, before you pull timing out...
  6. Replies
    7
    Views
    215

    Key on engine off, IAC should go to ~145. ...

    Key on engine off, IAC should go to ~145. Perhaps IAC is wired wrong. You make no mention of using BBC throttle body but your pic w lack of ridge at the bore opening suggest that. Pay attention to...
  7. Knock sensor....

    Knock sensor.:thumbsup:
  8. Replies
    5
    Views
    127

    Do you live in USA? Was thinking about purchasing...

    Do you live in USA? Was thinking about purchasing wb from them too. No issues shipping? Post back a product review. Thanx!
  9. Replies
    5
    Views
    127

    Me neither!...

    Me neither! http://www.gearhead-efi.com/Fuel-Injection/showthread.php?829-AutoProm-ADC-Interface-Channels-Set-up-in-TunerPro!
  10. Replies
    33
    Views
    2,550

    Initial spark advance in the bin calls for 0...

    Initial spark advance in the bin calls for 0 degrees. At idle your bin is calling for 20* + whatever your seat of the pants/ear timing you set it too. Idk if that's setting off the knock retard but...
  11. Replies
    33
    Views
    2,550

    Open loop, O2 very little variance from 450mv...

    Open loop, O2 very little variance from 450mv stoich and 2 minutes into log 20* w 4* knock retard bouncing things around. Volts seem a little low...code 43 knock sensor circuit failure.

    Went back...
  12. Replies
    1
    Views
    82

    http://www.gearhead-efi.com/Fuel-Injection/showthr...

    http://www.gearhead-efi.com/Fuel-Injection/showthread.php?1557-Cable-Installation-to-TunerPro-RT
  13. What he said to seat rings...wind it up and let...

    What he said to seat rings...wind it up and let the compression slow the vehicle down repeat like a dozen or so times.
  14. Replies
    5
    Views
    207

    Pic of vortec gasket sitting on intake... 14198

    Pic of vortec gasket sitting on intake...
    14198
  15. Replies
    10
    Views
    334

    If you find which COM port to use in question,...

    If you find which COM port to use in question, open your device manager to usb WITH your hardware DISCONNECTED. When you plug it into USB port, your new device will appear at which you can look at...
  16. Thread: low BLM

    by stew86MCSS396
    Replies
    48
    Views
    2,336

    Have you set your NEW injector flow constant? ...

    Have you set your NEW injector flow constant? You need to do this first and can calculate it bottom of page here: https://www.witchhunter.com/injectorcalc1.php

    What are you doing to the VE tables...
  17. HSR would be Holley Stealth Ram which would be...

    HSR would be Holley Stealth Ram which would be akin to a short runner TPI but still need to know which computer using. IDK much about MAF but I'm sure displacement and injector flow altered from...
  18. Replies
    12
    Views
    577

    If I'm not mistaken, 'V3T.ADX is for a TH-400.

    If I'm not mistaken, 'V3T.ADX is for a TH-400.
  19. I just purchased an engine that came with a 6395....

    I just purchased an engine that came with a 6395. Tried looking up the BCC but couldn't fine it under the 6395 bin files. Looked for the BCC in 7427 bin files and there it was, so with that said...
  20. Thread: low BLM

    by stew86MCSS396
    Replies
    48
    Views
    2,336

    You're not going to add columns or rows in your...

    You're not going to add columns or rows in your bin. Just copy the vortec ones that are there into yours. If yours has a column or row that the vortec table doesn't have then I would take the...
  21. 730 is from 90-92 F-body.

    730 is from 90-92 F-body.
  22. Replies
    4
    Views
    340

    IAC - Desired C/L Idle Speed

    IAC - Desired C/L Idle Speed
  23. Thread: 454 woes

    by stew86MCSS396
    Replies
    17
    Views
    755

    How's about the way the chip is inserted into the...

    How's about the way the chip is inserted into the burner? Notch towards the handle and chip inserted utilizing 28 pins away from the handle? If that didn't make any sense...click here:there's a...
  24. OP owns an Ostrich...just sayin.

    OP owns an Ostrich...just sayin.
  25. I would think that you probably could get away...

    I would think that you probably could get away with the higher spring pressure and then you need to do this:...
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4