Search:

Type: Posts; User: Keith74

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Thread: 93 4l60e tbi

    by Keith74
    Replies
    3
    Views
    2,484

    Hi Devon, have you changed the checksum to $AA ?

    Hi Devon, have you changed the checksum to $AA ?
  2. I hope he finds out what the issue is, I have had...

    I hope he finds out what the issue is, I have had my Autoprom for two years, when I figured out there was something not right with it after going through the entire electrical system on my truck...
  3. slimpikins, did you have any luck with talking to...

    slimpikins, did you have any luck with talking to Moates ?
  4. Excellent, Let us know how it goes.

    Excellent, Let us know how it goes.
  5. I have the same problem with the $OD on a 95...

    I have the same problem with the $OD on a 95 truck, data logging and emulating are very glitchy. I have been through every thing to try and eliminate the problem but have just resorted to flashing a...
  6. Replies
    0
    Views
    1,620

    1104060 Ramjet distributor question.

    Hi there,
    I have recently purchases a couple of brand new 1104060 distributors that where going cheap after my ICM failed in my original 1103952 distributor.
    My question is what is the difference...
  7. Replies
    3
    Views
    3,686

    Guys I have a quick question, Does lowering the...

    Guys I have a quick question, Does lowering the valves in the AE vs map and tps increase or decrease the fuel delivery?
  8. Replies
    3
    Views
    3,686

    Well I zeroed out the delay and tested the...

    Well I zeroed out the delay and tested the engine, It still has the slight delay but looking at the AE settings now as this is like the pump in a carb. I have a Holley throttle body so I am guessing...
  9. Replies
    3
    Views
    3,686

    PE Delay Question

    Hi all,

    Got my truck tuned nicely but have one small problem. at low speed when you step on the gas hard there is a small delay in response from the engine (about 1.5 seconds) then it powers up...
  10. Replies
    18
    Views
    25,663

    Hello Only_1, I am use Tunner Pro to program....

    Hello Only_1,
    I am use Tunner Pro to program.
    I'm not real sure about the undefined items in the tune but it was used as a base point for a start as I couldnt find any tunes to start with for my...
  11. Replies
    3
    Views
    3,676

    Thanks, this may explan the problem I have with...

    Thanks, this may explan the problem I have with the autoprom when tuning with the $AA mask. I may have a corrupt file.
  12. Replies
    3
    Views
    3,676

    Question about Mask ID

    Hey Guys, Was thinking the other day about after you burn a chip with the tune you have developed for your engine with the mask ID set to $AA how does leaving it as $AA effect the ECM in the long run...
  13. Replies
    5
    Views
    4,512

    Change your spark bias to 0 You will have to...

    Change your spark bias to 0
    You will have to redo your idle and open spark tables and you may find that not having enough advance will cause pinging. Check your timing is set at 0 on the dizzy.
  14. Replies
    5
    Views
    4,512

    Hello Mate, your timing table has all negative...

    Hello Mate,
    your timing table has all negative spark values. Unless i'm missing something why have you done this?
  15. Replies
    17
    Views
    11,507

    Cheers mate thats what I did, I read how to do...

    Cheers mate thats what I did, I read how to do this when I first started with tuner pro but with all the other things I had to figure out it was lower priority at the time and I forgot about it....
  16. Replies
    17
    Views
    11,507

    All good, had a brain fade and forgot about the...

    All good, had a brain fade and forgot about the hardware utility on TP.
  17. Replies
    17
    Views
    11,507

    Ohhh so i must have missed that! So how do you...

    Ohhh so i must have missed that! So how do you just burn the chip from my bin that I have created?
  18. Replies
    17
    Views
    11,507

    Well I have completed all my tuning after just...

    Well I have completed all my tuning after just working through the gliches, but the next drama I am experiencing is removing the autoprom and plugging the chip into the adaptor. The truck runs with...
  19. Replies
    17
    Views
    11,507

    This is exactly what has been happening with mine...

    This is exactly what has been happening with mine as well, so glad there is a answer as to what is going on :jfj:
  20. Replies
    0
    Views
    2,290

    TunerPro Glitch

    Hey everyone,
    Has any one had a glitch with either Tunerpro or the Autoprom before?
    Since I started using these systems on my previous engine and the new engine I have been experiencing a symptom...
  21. Replies
    18
    Views
    25,663

    That looks like a nice mod for the standard TBI...

    That looks like a nice mod for the standard TBI Woody.
    I think I will stick with the manifolds for now as they are trouble free and the car is not for racing.
  22. Replies
    18
    Views
    25,663

    Yep thats great if your vehicle is left hand...

    Yep thats great if your vehicle is left hand drive, the range is huge. Sadly these trucks are not that common here and having being converted to right hand drive the steering shaft runs inches from...
  23. Replies
    18
    Views
    25,663

    Hi Woody, I live in Central Queensland just west...

    Hi Woody,
    I live in Central Queensland just west of Rockhampton.
    Just curious as to what throttle body you are running with your set up?
    I could get more from my engine if I put a set of...
  24. Replies
    18
    Views
    25,663

    Good info bud, the 395 cam in my set up seems to...

    Good info bud, the 395 cam in my set up seems to haul ass from 1200 to 4500 rpm. no trouble overtaking a low end torque is good but still tuning to get it perfect, A dyno would be nice now.
  25. Replies
    18
    Views
    25,663

    That's great Danny, glad it helped.

    That's great Danny, glad it helped.
Results 1 to 25 of 28
Page 1 of 2 1 2