Well now it's showing spark advance but it's mid to high 50's. My main spark table doesn't go that high anywhere.
Type: Posts; User: dbuster
Well now it's showing spark advance but it's mid to high 50's. My main spark table doesn't go that high anywhere.
Ok thanks , I'll look at it later.
Looking over some logs I see that the spark advance never goes higher than 1, last log attached.
Finally had time to get back to this, did a few different flashes on my test unit and one on my car. It worked, successfully flashed a modified bin and my car still runs! Still have a lot to learn....
Ok, I believe that works! I was able to pull the bin run it through tuner pro and flash it back onto the ecm and read it again with flashhack. I will play with it some more tonight.
thank you,...
Down loaded new version, will try shortly.
Thanks
"Windows cannot open the folder"- The compressed folder(P66V6_read.rar.zip) is invalid
Down loaded flashhach, selected v6. Assuming that "Read calibration" is how I down load bin I get an error message.
DEBUG::flashhack Version BETA 0.5.8
DEBUG::Building read region map for TSIDE...
ok, thanks I will give it try.
I haven't had a chance to do any more data logging so I am practicing with what I have.
Down loaded bin from bench unit and loaded into tuner pro, opened data logs in trimalyzer and followed...
Not sure, I'll try.
I thought I replied to this yesterday but I must not have posted it. I some how miss placed about two hours of logs I made last week, and tonight I found that I can't load logs from eehack 4.7 and...
Ok guys, that seemed to work! As long as my laptop stays awake, and then all it did was disconnect. I was able to save the log and reconnect and drive on. logged 27 minutes.
I go back to work next...
Ok, thanks man, I will do that. Thank you for all the help, i know you guys are busy and I appreciate you taking the time to walk me through this. I’ll get it figured out and keep posting. Let me...
So do I need eehack 4.7? This is where I'm getting confused. If I'm using eehack_v6 (p66hack sounds good)do I need eehack 4.7?
I've gone back and reread all the instructions you guys have given me and I may be little confused here. At first I understood that I should launch eehack and load the v6 definition files. Never...
Thanks guys,
Just to be clear I am using eehack_v6_w4_4.
I also have eehack 4.9.1
I have also been logging with tunerpro and using trimalyzer.
Tried more data logging tonight, if I go longer than about 10 minutes EEHACK_V6 freezes and will not respond and I lose the data for that run. If I stop and save the log along the way it's ok, but if...
95 minutes of logs, 369,076 counts and 800 events.
Reading the OBD1 swap article says the knock sensor should match the car the ECM came out of. I figured I would do that first.
Did some more data logging and playing with trimalyzer. Was able to analyze logs and load into tuner pro and modify ve table. unable to load new modified bin into eehack_v6. Not $EE bin.
Saw that...
Figured out how to analyze individual logs.
Did some more data logging, still have a couple of issues and questions. Still having a problem with eehack freezing up on longer runs,not always able to save logs.
Would like to be able to...
I have one with a bad injector driver that I will practice on and then pick up another good one to practice with.
The first test tries in the garage without data logging when I would close the program it would ask if I wanted to save logs so that's how I have been doing it. On the two short drives it worked fine...
Went out twice today to log data with eehack_v6 and when i tried to disconnect it locked up and would not respond. both times it eventually closed without saving data. I've done a couple of short...