Search:

Type: Posts; User: JP86SS

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    4,813

    If you know the addresses you could use a Mode 2...

    If you know the addresses you could use a Mode 2 or Mode 3 command to get the data out.
    It would take more mental power to apply the BLM values retrieved to your tune than a good datalog would....
  2. Replies
    10
    Views
    8,561

    Pretty sure you need "Running" indication which...

    Pretty sure you need "Running" indication which would be the DRP.
    DRP is a square wave.
    Here is a variable one I built for my test bench but you could just make it constant RPM....
  3. Thread: tpi fuel system

    by JP86SS
    Replies
    2
    Views
    4,522

    The 92' style TPI code in the 727 or 730, 749...

    The 92' style TPI code in the 727 or 730, 749 ECMs expect to have the fuel pressure controlled via the vacuum reference.
    This keeps the commanded fuel output linear over the different manifold...
  4. Replies
    12
    Views
    11,887

    Not certain, but most logic requires a "stop"...

    Not certain, but most logic requires a "stop" motion or very low to get to the "idle" condition.
    You would need to adjust where the minimum speed for idle is at in the bin.
    DRAC is the best option...
  5. Replies
    6
    Views
    5,921

    That is mask $8D, timing info is shown in data....

    That is mask $8D, timing info is shown in data.
    Is this a new build?
    What is the BCC you are using? (ANHT ?)
    If so, you may have a V6 memcal in there, not the V8.
  6. Not sure if the TBI has IAC control or not. If...

    Not sure if the TBI has IAC control or not.
    If so, there should be a setting for "Warm Park" position and Cold position.
    It makes it much easier to crank when the TB is open than with it closed....
  7. Thread: Double delta AE

    by JP86SS
    Replies
    2
    Views
    3,078

    That could be a reference to "doubling" the...

    That could be a reference to "doubling" the amount of AE in a table that has row values based on the "delta" TPS or "delta" MAP value.
    I don't have any particular link.
  8. Replies
    16
    Views
    11,705

    It's best to remember that USERS built the...

    It's best to remember that USERS built the definition files.
    Some are better than others, some are just wrong. Its because information is scattered and not always done by a single person.
    You...
  9. Replies
    17
    Views
    10,756

    What did it come out of? 0x0008 = 49 HEX for the...

    What did it come out of?
    0x0008 = 49 HEX for the Mask ID if that is the right location of it.
    Attached pic of the area.
    Jp
  10. Thread: Silly Questions

    by JP86SS
    Replies
    123
    Views
    71,033

    ECM: For TunerPro you need 3 things 1.)...

    ECM:
    For TunerPro you need 3 things

    1.) Editor Definition "XDF" FILE for your "Mask ID" ($0D or $E6 whatever yours is running)
    2.) Datastream (Logging) Definition "ADX" file (also for the Mask...
  11. Replies
    2
    Views
    4,143

    S_AUJP was modded just for those types of...

    S_AUJP
    was modded just for those types of applications.
    Look for latest V4 or the new V5 versions.

    BTW, Memcal resistors are not fully known for making changes.
    The binary software program...
  12. Replies
    5
    Views
    6,272

    Do not emulate with a chip in the socket on the...

    Do not emulate with a chip in the socket on the AP.
    Chip only goes into the socket if you are burning or reading it.

    Your code 51 could also be that you didn't make the mask ID = to AA....
  13. Replies
    5
    Views
    4,367

    UPDATE: Cleaned out TB and New O2 sensor solved...

    UPDATE:
    Cleaned out TB and New O2 sensor solved it!
    Now onto the trans not starting in 1st when hot problem.
    157 K miles and still runs good!
  14. Replies
    24
    Views
    17,364

    Do you mean the VATS signal? It can be anything...

    Do you mean the VATS signal?
    It can be anything from 33-66 Hz IIRC.

    You can change the min and max parameter in some of the bins.
  15. Replies
    1
    Views
    3,581

    VATS is turned off in that file but the error...

    VATS is turned off in that file but the error codes for VATS are still enabled.
    Not sure if that would come from factory that way.
    That's an odd combination of settings.
  16. Replies
    5
    Views
    4,367

    Yep, I wish I could stay away too! I did find...

    Yep, I wish I could stay away too!
    I did find that it will log with $0D using my AutoProm.
    My other cable must have issues.
    O2 sensor does not change much at all when running. Doesn't go into CL...
  17. Replies
    5
    Views
    4,367

    New to me...94' LB4 "Z" (what PCM?)

    I'm struggling to find the proper definitions, bins, etc for this S10 truck I bought.
    4.3L V6 TBI, with E-Trans (4L60E), VIN designates as a "Z" (not a turbo like some lists indicate)
    I'm thinking...
  18. Thread: ALDLdroid

    by JP86SS
    Replies
    1,128
    Views
    906,382

    Nope, someday maybe. Focus on your main...

    Nope, someday maybe.
    Focus on your main objectives first.
    Jp
  19. Thread: ALDLdroid

    by JP86SS
    Replies
    1,128
    Views
    906,382

    The OBDII ADX usage is more of a utility thing to...

    The OBDII ADX usage is more of a utility thing to enable veiwing items, not a true logging app.
    I have torque, TP5, and a bunch of hand scanners/software.
    I like to use TP for everything. the ADX...
  20. Thread: ALDLdroid

    by JP86SS
    Replies
    1,128
    Views
    906,382

    Can't believe I've missed this whole development!...

    Can't believe I've missed this whole development!
    Going to pick up this app for sure as well as the BT OBDI connection. (Santa, Santa, Santa!)
    I'd like to try it now with my BT on OBDII GTO since...
  21. Replies
    40
    Views
    28,430

    Also check your engine to firewall ground wire is...

    Also check your engine to firewall ground wire is intack.
    The fender to the battery one to while your checking.
    Jp
  22. Replies
    19
    Views
    17,335

    A/C code changed.

    Remember in the latest S_AUJP, the clutch is not disabled at high speed as in the original code.
    just don't go stomping too much with the A/C on. :)

    Most of the code jumps up the RPM when A/C is...
  23. Replies
    12
    Views
    14,631

    In $8D it is selectable which of the two voltages...

    In $8D it is selectable which of the two voltages is used for injector compensation.
  24. Replies
    15
    Views
    13,875

    The PDF of the ANHT is seriously flawed and has...

    The PDF of the ANHT is seriously flawed and has errors even though it helped to get the AUJP commented.
    Download the AUJP files from Moates site (or here if EagleMark has them)
    AUJP_JP2.zip is...
  25. Replies
    27
    Views
    24,525

    To clarify this for me... Sensor 1 is the...

    To clarify this for me...
    Sensor 1 is the Pre-Cat sensor
    Sensor 2 is post-Cat sensor
    Bank 1 = cylinders 1,3,5, & 7
    Bank 2 = cylinders 2,4,6 & 8
    That's the only way it seems to make sense to me...
Results 1 to 25 of 60
Page 1 of 3 1 2 3