Search:

Type: Posts; User: pmkls1

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. What fuel pump is it you're running ? What type...

    What fuel pump is it you're running ? What type of fuel pressure regulator are you running ? Is it a stock housing modified to be adjustable or is it an aftermarket housing ? Are you positive that...
  2. Replies
    47
    Views
    130,924

    Sticky: Wow, I am without words really. I haven't visited...

    Wow, I am without words really. I haven't visited the site in months because I just haven't had the time so I am just now learning of his passing. I actually had to leave the page for a minute and...
  3. Replies
    11
    Views
    10,313

    I can explain to you with confidence how the...

    I can explain to you with confidence how the vehicle is configured which will answer most of your questions as I have intimate knowledge of those vehicles. I have no knowledge of EFI Live, but can...
  4. Replies
    11
    Views
    10,313

    No, I meant that I was assuming that this...

    No, I meant that I was assuming that this question was regarding the drivetrain swap he was working on and that the technical info I gave would pertain to the particular vehicle that the drivetrain...
  5. Replies
    11
    Views
    10,313

    There is a lot of interesting info there Shannen....

    There is a lot of interesting info there Shannen. I knew that if anyone had a decent answer it would be you. I was hoping that although slightly OT, my question might yield answers containing...
  6. Replies
    11
    Views
    10,313

    That part of the calculation was where I was a...

    That part of the calculation was where I was a little uncertain about my answer thus my leaving it out of my reply. Your answer actually raises two questions for me though. They are related, but may...
  7. Replies
    11
    Views
    10,313

    This is just an educated guess based on your...

    This is just an educated guess based on your screenshot and experience. But, the driven wheel pulses per rev is based on the final drive ratio & number of teeth on the VSS reluctor. I am assuming...
  8. Thread: EagleMark

    by pmkls1
    Replies
    121
    Views
    128,504

    I hope that everything goes ok. Best of luck to...

    I hope that everything goes ok. Best of luck to you Mark.
  9. Replies
    79
    Views
    69,166

    There is a possibility of getting just the...

    There is a possibility of getting just the connector body, but obtaining the part number would probably be easier through viewing the wiring schematics. If you view the portion of the schematics that...
  10. Replies
    79
    Views
    69,166

    Dave, I BELIEVE that you are correct about how...

    Dave,

    I BELIEVE that you are correct about how the ECM controls the fans and that is why your wiring and test results support your theory. That was how I understood the system to work going by the...
  11. Replies
    79
    Views
    69,166

    Wow guys, I didn't mean to spark off an argument...

    Wow guys, I didn't mean to spark off an argument here. I only took issue with being told I was wrong without an explanation as to why as I was confident in my knowledge of how these systems are...
  12. Replies
    79
    Views
    69,166

    As a matter of fact yes it is. I don't take issue...

    As a matter of fact yes it is. I don't take issue with being corrected. It is the manner in which it is done. That being said, I would like to get back on track as well.

    I actually thought that I...
  13. Replies
    79
    Views
    69,166

    I could ask you how much training you received...

    I could ask you how much training you received from General Motors pertaining to their High Speed GMLAN network and how many GM engineers you have consulted with, but this is supposed to be an...
  14. Replies
    79
    Views
    69,166

    That's not what I have found in my experience or...

    That's not what I have found in my experience or what I was told by the GM engineers at the training facility.
  15. Replies
    79
    Views
    69,166

    After looking at the schematics you posted it...

    After looking at the schematics you posted it appears that the BCM may simply provide a switched +12v signal to all modules on the network to power them on. If you notice in the schematics, the ECM...
  16. Replies
    79
    Views
    69,166

    Wiring diagrams are split up into their...

    Wiring diagrams are split up into their corresponding category so sometimes they can be difficult to locate. I.E. The wiring diagram for a brake switch input at the ECM from the ABS system may be...
  17. Replies
    79
    Views
    69,166

    Dave, Glad you found what you needed for the...

    Dave,

    Glad you found what you needed for the diodes. As for your need for info on circuits I have a suggestion that may be of great assistance. You can actually buy a trial subscription to the GM...
  18. Replies
    79
    Views
    69,166

    I know it's been a while since I posted about the...

    I know it's been a while since I posted about the diodes, but I've not had much time for anything lately. I'm not sure if you found any more info on the diodes either, but here are a couple pics I...
  19. Replies
    28
    Views
    36,210

    All personal preferences aside, I'm glad that you...

    All personal preferences aside, I'm glad that you found a solution to your problem. On a related note, I feel compelled to state that although I prefer to use iridium plugs and that they are the...
  20. Replies
    79
    Views
    69,166

    Dave, after looking at that schematic I can tell...

    Dave, after looking at that schematic I can tell you that the diodes are either integral to the fuse block OR the more likely possibility is that they plug into the fuse block like standard blade...
  21. Replies
    9
    Views
    10,754

    The vapor lock theory sounds like another very...

    The vapor lock theory sounds like another very likely reason for the little orifice there. I hadn't thought of that, but it makes more sense than an air bleed. I never did understand why the TBI...
  22. Replies
    9
    Views
    10,754

    Here is your pic with notes illustrating what I...

    Here is your pic with notes illustrating what I mean. It's a little sloppy, but I think you can get the idea.


    6959
  23. Replies
    9
    Views
    10,754

    You've got the flow path backwards. The fuel has...

    You've got the flow path backwards. The fuel has already reached the injectors and is on it's way out to the return line at that point. I do not know the purpose of the little orifice, but if the...
  24. Replies
    13
    Views
    10,430

    Mark, I have a brand new still in the box Turbo...

    Mark, I have a brand new still in the box Turbo Sunbird memcal that I bought for a project that I never got around to. I will dig it out today and get you the p/n and BCC. PM me if you're interested.
  25. Replies
    28
    Views
    36,210

    .035" would be the ideal gap on that engine. I...

    .035" would be the ideal gap on that engine. I prefer not to go much wider than that on most applications. I've heard both ways on aftermarket "performance" coils, but I've never seen any hard...
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4