Just a couple of xls files of driving logs. Wondering if you notice anything that stands out. One one of the files this are a few hover buttons on the left with popup info. Thanks

I was wondering about a higher temperature to enable cl. Also if I unplug the maf it runs great. I also noticed upon coldstart the map reads in the 40 _ 50 kpa range before settling down to 38ish....

Hey Kur4o, thanks for the quick response. I'm using ver 20.26 with a obdx pro vt,
see I had the same error before, back on page 5 #66 of this thread. I believe it was fixed
by reinstalling. I'll...

hey guys, its been a while. Question for you. I seem to be getting this error code lately when using Univ Patcher logger
unable to transmit 6c fe fd 20
that or unable to set bus quiet. If i wait a...

Car basically runs great. Trying to tune for unseasonably cold weather, only issue is cold idle transitioning to closed loop. When the air pump turns off, engine wanted to stall for10 seconds or so,...

hey guys, here are some screenshots of a log. What does it look like to you, especially the 2nd pic with the highlighted section. Curious on you thoughts.

Duke, I loaded your bin in TunerRT, sourced a 12221588 xdf and took the attached screenshot. Doesn't it show that B4206 is enabled? This xdf describes the 4206 very well, the xdf for my car doesn't...

Hey Duke,did you ever determine what B4206 does I'm curious also. What became of your idle issue, fixed?

Hey guys, the weather here has gotten much colder, mid 50* (Palm Springs,CA) and the tune is from the summer when it was 120*. It seems now that as soon as the air pump turns off, the idle drops and...

I found the missfire table using a different xdf, that was the issue.
18723old table
18724new one.
Seems to work, thanks.

Good to know, thanks. I only use perf mode in light to light every now & then. Mostly just to chirp into 2nd without looking like I meant to.

Car runs great. Tables look like it shouldn't. Logs show large 10+ ltft's, stft's seem good less than 10, usually about 5. I started with the original 9****** ecu and there was no xdf support so I...

Uh oh! I tried to do a pcm read and it errored out! Battery was fully charged. Now turn on the key and no power. Disconnected battery, reconnected, still no power. Currently on charger, shows it it...

I think you are right. I just noticed sometimes viewing the graph with the button pushed and not being aware of it. I did try copying the old one to this tune and the car would barely even start. My...

Hey Guys, just looking through ve tables for curiosity regarding that flashing light. Here is my old table vs new table. Shocked at the difference.
1866918670
I would think the old one looks more...

No, I don't even know what that is. Please explain, thank you!

All dtc's are off. They were set to no light but set a code. When checked, no code. The engine feels smooth and all items in torque app look good while the light is flashing. Tried logging with...

Ralmo94
I used the spreadsheet, works great thank you. I seem to have a check engine light that flashes between 70 & 80 mph under light throttle. If I add throttle the car speeds up...

Will check it out, thank you.

Guys, running well. Getting to play in more tables and customizing adf file for ease of use and organizing. Dialing in tcc for better fuel economy. Curious on what controls pressure & shift speed for...

Thanks for the quick reply, good to know for my next one!

I left a OBDXPRO VT V3 adaptor plugged into the obd port. I do that often but I'm normally driving the car daily so its not an issue. Last week I left in plugged in and left town. A week later when I...

I was checking out new values in tables i hadn't looked at yet. Found one "Throttle_Load" and it showed a non linear mapping of the throttle opening compared to pedal movement. Not etc control but...

Kur40, thanks for the quick reply. The wire going to the ECU has to go to a different pin than the one I wired my switch up to, since the pin I wired to was unused by the vehicle harness. I think...

Hey guys it's been a while, just wanted to say hi. I'm really enjoying my performance button and wanted to hook it up permanently. I've been looking for pinouts for a second gear start switch and...